• Journal of Ceramic Processing Research
• /
• v.19 no.6
• /
• pp.461-466
• /
• 2018

The effects of Ca/Sr ratio and the sintering temperature on the properties of $(Ca_xSr_{(1-x)})ZrO_3$ (CSZ) ceramics were investigated in this study. CSZ ceramics were prepared using solid-state reaction process, which were sintered in air at temperatures ranging from $1350^{\circ}C$ to $1450^{\circ}C$. Their structures were characterized by X-ray Diffraction (XRD), Scanning Electron Microscopy (SEM), and Transmission Electron Microscopy (TEM). The change in Ca/Sr ratio significantly affected the crystalline phase and the dielectric properties of the $(Ca_xSr_{(1-x)})ZrO_3$ ceramics. The secondary phase, $Ca_{0.15}Zr_{0.85}O_{1.85}$, was observed and increased correspondingly with the rising of sintering temperatures. In order to understand the effects of secondary phase on the dielectric properties of CSZ ceramics, the $Ca_{0.15}Zr_{0.85}O_{1.85}$ phase was prepared individually using solidstate method. The $Ca_{0.15}Zr_{0.85}O_{1.85}$ ceramics sintered at $1500^{\circ}C$ for 2 hours possessed a dielectric constant (${\varepsilon}_r$) of 21.7, a dielectric loss ($tan{\delta}$) of $49.510^{-4}$ and an Insulation Resistance (IR) of $2.1{\times}10^{10}{\Omega}$. The ($Ca_{0.7}Sr_{0.3})ZrO_3$ ceramics exhibited the best dielectric properties, with a permittivity of 29, a dielectric loss ($tan{\delta}$) of $2.7{\times}10^{-4}$, and an Insulation Resistance (IR) of $2.6{\times}10^{12}{\Omega}$.

• Tribology and Lubricants
• /
• v.16 no.3
• /
• pp.182-187
• /
• 2000

In this paper the residual stresses on lubricated sliding surfaces were measured during break-in procedure and up to scuffing by the X-ray diffraction method. The cylinder-on-disk type tribometer was used with the line-contact geometry. Scuffing tests were done using a constant load. In the break-in procedure the loads were increased from very low values in several steps. It was found that the sliding surfaces with break-in represented relatively higher values of residual compressive stresser than those without break-in. The residual stresses below the surfaces showed the small amount of stress increases. The results of scuffing tests with and without break-in showed the same trends as break-in tests did. However, in case of tests with break-in procedure the stresses below the surfaces showed very large increases in the residual compressive stresses. From the tests of break-in and scuffing, it was found that the increases in scuffing lives were related with the increases of residual stresses on the lubricated sliding surfaces with break-in.

• Applied Chemistry for Engineering
• /
• v.22 no.5
• /
• pp.479-485
• /
• 2011

Pt-Bi/C catalysts supported on carbon black with various Pt/Bi ratios were synthesized by a reduction method. Chloroplatinic acid hydrate ($H_2PtCl_6{\cdot}xH_2O$) and bismuth (III) nitrate pentahydrate ($Bi(NO_3)_3{\cdot}5H_2O$) were used as precursors for Pt and Bi, respectively. Before loading metal on carbon, heat treatment and pretreatment of carbon black in an acidic solution was conducted to enhance the degree of dispersion. The physical property of the synthesized catalysts was investigated by X-ray diffraction and X-ray photoelectron spectroscopy. The XRD pattern of untreated Pt-Bi/C catalyst showed BiPt and $Bi_2Pt$ peaks in addition to Pt peaks. These results imply that Bi atoms were incorporated into the Pt crystal lattice by Pt-Bi alloy formation. The catalytic activity for methanol oxidation was measured using cyclic voltammetry in a mixture of 0.5 M $H_2SO_4$ and 0.5 M $CH_3OH$ aqueous solution. The addition of proper amount of Bi was found to significantly improve catalytic activity for methanol oxidation. The catalytic activity for methanol oxidation was closely related to the stability between electrode and electrolyte. In order to investigate the stability of catalysts, chronoamperometry analysis was carried out in the same solution at 0.6 V.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2006.05a
• /
• pp.395-398
• /
• 2006

Forging is applied for many industrial fields. Also, it is applied to hose nipple. Stress and metal analysis is finding method of forging possibility and we predict this possibility by finite element forging analysis. But there are also many manufacturing procedure after forging, and metal texture is varied by additional heat treatment or coating. So this research is focused on the measuring and analysis of plastic residual stress distribution at overall manufacturing procedure. From raw material to final product we measured real residual stress at each manufacturing procedure by X ray diffract meter, and simulated another procedure except forging by nonlinear finite element analysis. Also we showed how Zn-Ni coating is more contributable to metal strength than Zn coating. By this research we make final conclusion that process analysis must be observed from raw material to final manufacturing state for robust design.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.8 no.1
• /
• pp.83-90
• /
• 1998

Stage transformation characteristics of Li, K and Na-graphite deintercalation compounds (GDICs) were studied under consideration of a deintercalation mechanism of the intercalants between carbon layers. Li-graphite intercalation compounds (GICs) synthesized by a controlling temperatures and pressures have been spontaneously decomposed in the atmosphere. By X-ray differaction analysis the $d_{001}$-values of stage 1 and 2 were identified to be 3.71 and 7.06 $\AA$, respectively. After 6 weeks, the deintercalation reaction of the Li-GICs ceased and only residual compounds could be observed. K-GICs were synthesized by the modified two-bulb method resulting in structural stabilities and stage transitions. By X-ray diffraction analysis the very stable K-graphite residue compounds were observed after 10 weeks. Na-GICs with stage 1 and 2 were synthesized using the high temperature and pressure technique. The temperature dependence of a deintercalation reaction and a thermal stability of Na-GICs were discussed. The structure changes of the Na-GDICs depending on heating rates were identified by X-ray diffraction. According to the deintercalation process, the stage transformations could be attributed to irregular deintercalations of the GDICs with disordered stage.

• Journal of the Korean Vacuum Society
• /
• v.5 no.1
• /
• pp.67-72
• /
• 1996

$RU_{1-x}Ir_xO_2$ films were deposited on the quartz substrate by a spray pyrolysis method. The x-ray diffraction patterns showed that the structure of the $RU_{1-x}Ir_xO_2$ film was tetragonal and the lattice constant $a_o$ and $c_o$ were increased from 4.495 A to 4.058 A and from 3.092A to 3.156 A, respectively as the Ir composition varied from 0.0 to 1.0. The $RU_{1-x}Ir_xO_2$ film was metallic and the resistivity of the samples was increased from $7{\times}10^{-5}{\Omega}\textrm{cm}$ to $48{\times}10^{-5}{\Omega}\textrm{cm}$ with increasing the Ir x. The surface of the sample was slightly roughed, the grain size and the grain boundary width were increased as the Ir composition varied from 0.0 to 1.0.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.23 no.5
• /
• pp.706-711
• /
• 1986

The AgGa1-xInxSe2 films are deposited by a flash evaporation method onto pyrex glass substrates at temperatures between 5\ulcorner and 360\ulcorner. The single crystalline films which have X-ray diffraction peak of only (112) plane are preared at substrate temperature above 360\ulcorner. The prepared AgGa 1-xInxSe2 films are high photosensitive. The temperature coefficients of energy gap are found to be (-1.2~-4.0)x10**4 eV/K and (-3.1~-5.2)x10**-4 eV/K, and that of peak energy of spectral photoresponse curve are found to be (-1.1 ~ -3.0)x10**-4 eV/K(50K~100K) and (-2.4~-5.1)x10**-4 eV/K(100K~300K).

• Journal of Magnetics
• /
• v.14 no.2
• /
• pp.93-96
• /
• 2009

The Mn-substituted M-type Ba-ferrite ($BaFe_{12-x}Mn_xO_{19}$; x = 0, 2, 4, 6) powders were prepared by the HTTD (High Temperature Thermal Decomposition) method. The effect of $Mn^{3+}$ Jahn-Teller ions on the magnetic properties has been studied by x-ray diffraction, vibrating sample magnetometry, and $M{\ddot{o}}ssbauer$ spectroscopy. With increasing Mn substitution, the lattice parameter $a_0$ increases while $c_0$ decreases. The magnetocrystalline anisotropy constants ($K_1$) were determined as 2.9, 2.2, 1.8, and, $1.3{\times}10^6\;erg/cm^3$ for x = 0, 2, 4, and 6, respectively, by the LAS method. We have studied the change of cation distribution by $M{\ddot{o}}ssbauer$ spectroscopy which is closely related to $K_1$.

• Bulletin of the Korean Chemical Society
• /
• v.34 no.5
• /
• pp.1445-1453
• /
• 2013

$Zn_{(1-x)}Ni_xAl_2O_4$ (x = 0.0-1.0) spinels were prepared at $800^{\circ}C$ by co-precipitation method and characterized by infrared spectroscopy, X-ray diffraction, scanning electron microscopy and X-ray photoelectron spectroscopy. The specific surface area was determined by BET. SEM image showed nano sized spherical particles. XPS confirmed the valence states of the metals, showing moderate Lewis character for the surface of materials. The powders were successfully used as new heterogeneous catalysts of Biginelli's reaction, a one-pot three-component reaction, leading to some dihydropyrimidinones (DHPMs). These new catalysts that produced good yields of DHPMs, were easily recovered by simple filtration and subsequently reused with persistent activity, and they are non-toxic and environmentally friendly. The optimum amount of catalyst is 20% by weight of benzaldehyde derivatives, while the doping amount has been found optimal for x = 0.1.

• Journal of the Korean Magnetics Society
• /
• v.20 no.6
• /
• pp.207-211
• /
• 2010

We have investigated the magnetoresistance effect in $Cr_5S_6$ single crystals prepared by vapor transport method. Room temperature X-ray diffraction (XRD) study reveals the phase formation of the single crystals with trigonal crystal structure. The magnetization was measured as a function of temperature (5 K~400 K) and applied magnetic field (0.1 T and 5 T). The magnetization curve as a function of temperature reveals the two transition states of $Cr_5S_6$: one from antiferromagnetic to ferrimagnetic state at ~150 K and the other from ferrimagnetic to paramagnetic state at ~300 K. Temperature dependent resistivity at 0 T and 5 T magnetic field shows the metallic behavior, showing the transition from antiferromagnetic to ferrimagnetic state at ~150 K. Magnetic field dependence of magnetization was measured at four fixed temperatures viz. 100 K, 150 K, 200 K, and 300 K. It is observed that at 200 K and 300 K it shows well M-H hysteresis behavior, whereas at 100 K and 150 K it shows non-hysteretic nature. A negative magnetoresistance (MR) of -2% is observed at 5 T for $Cr_5S_6$ single crystal at 150 K, near the antiferromagnetic transition temperature.