• Korean Journal of Materials Research
• /
• v.23 no.4
• /
• pp.211-214
• /
• 2013

The effects of a Ni coating on the sensing properties of nano ZnO:Ni based gas sensors were studied for $CH_4$ and $CH_3CH_2CH_3$ gases. Nano ZnO sensing materials were prepared by the hydrothermal reaction method. The Ni coatings on the nano ZnO surface were deposited by the hydrolysis of zinc chloride with $NH_4OH$. The weight % of Ni coating on the ZnO surface ranged from 0 to 10 %. The nano ZnO:Ni gas sensors were fabricated by a screen printing method on alumina substrates. The structural and morphological properties of the nano ZnO : Ni sensing materials were investigated by XRD, EDS, and SEM. The XRD patterns showed that nano ZnO : Ni powders with a wurtzite structure were grown with (1 0 0), (0 0 2), and (1 0 1) dominant peaks. The particle size of nano ZnO powders was about 250 nm. The sensitivity of nano ZnO:Ni based sensors for 5 ppm $CH_4$ gas and $CH_3CH_2CH_3$ gas was measured at room temperature by comparing the resistance in air with that in target gases. The highest sensitivity of the ZnO:Ni sensor to $CH_4$ gas and $CH_3CH_2CH_3$ gas was observed at Ni 4 wt%. The response and recovery times of 4 wt% Ni coated ZnO:Ni gas sensors were 14 s and 15 s, respectively.

• Journal of the Korean institute of surface engineering
• /
• v.47 no.4
• /
• pp.204-209
• /
• 2014

The electrodeposition of ZnO nanorods was performed on ITO glass. The optimization of two process parameters (solution temperature and growth time) has been studied in order to control the orientation, morphology, density, and growth rate of ZnO nanorods. The structural and optical properties of ZnO nanorods were systematically investigated by using field-emission scanning electron microscopy, X-ray diffractometer, and photoluminescence. Commonly, the results of the structural property show that hexagonal ZnO nanorods with wurtzite crystal structures have a c-axis orientation, and higher intensity for the ZnO (002) diffraction peaks. Furthermore, the nanorods length increased with increasing both the solution temperature and the growth time. The results of the optical property show a strong UV (3.28 eV) peaks and a weak visible (1.9~2.4 eV) bands, the intensity of UV peaks was increased with increasing both the solution temperature and the growth time. Especially, the UV peak for growth of nanorods at $75^{\circ}C$ blue-shift than different temperatures.

• Journal of the Korean institute of surface engineering
• /
• v.47 no.4
• /
• pp.198-203
• /
• 2014

ZnO nanorods have been deposited on ITO glass by electrodeposition method. The optimization of two process parameters (precursor concentration and current) has been studied in order to control the orientation, morphology, and optical property of the ZnO nanorods. The structural and optical properties of ZnO nanorods were systematically investigated by using field-emission scanning electron microscopy, X-ray diffractometer, and photoluminescence. Commonly, the results show that ZnO nanorods with a hexagonal form and wurtzite crystal structure have a c-axis orientation and higher intensity for the ZnO (002) diffraction peaks. Both high precursor concentration and high electrodeposition current cause the increase in nanorods diameter and coverage ratio. ZnO nanorods show a strong UV (3.28 eV) and a weak visible (1.9 ~ 2.4 eV) bands.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1998.02a
• /
• pp.107-107
• /
• 1998

GaN 에피택시 층의 전기적, 광학적 특성 및 표면 형상의 향상을 위한 전처리 공 정으로서 사파이어 기판의 질화 처리가 많이 행해지고 있는데 이는 표면에 질화 충올 형성시킴으로서 GaN 충과의 계면에너지 및 격자상수 불일치를 줄여 GaN 충의 성장을 촉진시킬 수 있기 때문이다 본 실험에서는 고 진공 하에서 유도 결합 플라즈마를 이용하여 사파이어 기판의 질화 처리를 행한 후 XPS와 AFM을 이용하여 기판 표면의 질소 조성과 표면 형상을 관찰하였다. 기판 표면의 질소 조성은 질소 가스의 유입량과 기판의 온도보다 칠화 시 간 및 RF-power에 의해 크게 좌우되나 표면 형상은 기판의 온도에 크게 영향올 받는 것으로 나타났다. 따라서 본 실험에서는 기판의 온도를 낮춤으로서 protrusion이 없는 매끈한 표면의 질화 충을 얻올 수 있었다. 핵생성 충의 성장 없이 450 oC의 저온에서 GaN 충올 성장시킨 결과 육방 대청성 의 wurtzite구조를 가지며 bas허 plane이 사파이어 기판과 in-plane에서 300 회전된 관계 를 갖고 있는 것올 XRD -scan으로 관찰하였다. 또한 GaN 충의 성장이 진행됩에 따라 결정성이 향상되고 있는 것이 뼈S ali맹ed channeling 실험올 통해 관찰되었으며 이는 G GaN 충의 두께 중가에 따라 결정성이 향상된다는 것올 의미한다 사파이어 기판의 질 화 처 리 시 간이 증가함에 따라 후속 성 장된 GaN 층의 bas외 pI뻐e에 대 한 XRD -rocking c curve의 반치폭이 감소하는 것으로 나타났는데 이는 기판의 표면이 질화 충으로 전환 됨에 따라 각 GaN island의 c-축이 잘 정렬됨올 의미한다. 또한 AFM으로 ~이 충의 표 면 형상올 관찰한 결과 기판의 질화 처리가 선행될 경우 lateral 방향으로의 G뼈 충의 성장이 촉진되어 큰 islands로 성장이 일어나는 것으로 관찰되었는데 이는 질화 처리가 선행될 경우 Ga과 N의 표면 확산에 대한 활성화 에너지가 감소되기 때문인 것으로 생 각된다 일반적으로 GaN 에피택시 충의 결정성의 향상과 lateral 생장올 도모하기 위하여 성장 온도를 증가시키지만 본 실험에서는 낮은 성장 온도에서도 결정성의 향상 및 l later빼 성장을 촉진시킬 수 있었으며 이는 저온 성장법에 의한 고품위의 GaN 에피택시 충 성장에 대한 가능성올 제시하는 것이다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.285-285
• /
• 2010

Zinc oxide (ZnO) is a direct band gap semiconductor with 3.37 eV, which has in a hexagonal wurtzite structure. ZnO is a good candidate for a photocatalyst because it has physical and chemical stability, high oxidative properties, and absorbs of ultraviolet light. During ZnO is irradiated by UV light, redox (reduction and oxidation) reactions will occur on the ZnO surface, generating the radicals O2- and OH. These two powerful oxidizing agents have been proven to be effective in decomposition of harmful organic materials, converting them into CO2 and H2O. Therefore, we assume that oxygen on the surface of ZnO is a very important factor in the photocatalytic activities of ZnO nanoparticles. Recently, ZnO nanoparticles are studied in various application fields by many researchers. Photocatalyst research is progressing much in various application fields. But the ZnO nanoparticles have disadvantage that is unstable in water in comparison titanium dioxide (TiO2). The Zn(OH)2 was formed at the ZnO surface and ZnO become inactive as a photocatalyst when ZnO is present in the solution. Therefore, we prepared synthesized ZnO nanoaprticles that were immersed in the water and dried in the oven. After that, we measured photocatalytic activities of prepared samples and find the cause of their phtocatalytic activity changes. The characterization of ZnO nanoparticles were analyzed by Scanning Electron Microscopy (SEM), X-ray diffraction (XRD) and BET test. Also we defined the photocatalytic activity of ZnO nanoparticles using UV-VIS Spectroscopy. And we explained changing of photocatalytic activity after the water treatment using X-ray Photoelectron Spectroscopy (XPS).

• Journal of the Korean Society for Heat Treatment
• /
• v.26 no.6
• /
• pp.288-292
• /
• 2013

We have considered the influence of electron irradiation energy of 300, 600 and 900 eV on the stuctural, electrical and optical properties of GZO/$TiO_2$ thin films prepared with RF magentron sputtering. The optical transmittance and electrical resistivity of the films were dependent on the electron's irradiation energy. The electron irradiated GZO/$TiO_2$ films at 900 eV are grown as a hexagonal wurtzite phase and the resistivity is decreased with electron irradiation energy. The GZO/$TiO_2$ films irradiated at 900 eV shows the lowest resistivity of $4.3{\times}10^{-3}{\Omega}cm$. The optical transmittance in a visible wave length region also increased with the electron irradiation energy. The film that electron irradiated at 900 eV shows 82% of optical transmittance and higher work function of 5.18 eV in this study.

• Journal of the Korean Vacuum Society
• /
• v.18 no.5
• /
• pp.384-389
• /
• 2009

ZnO, a wurtzite lattice structure, has attracted much attention as a promising material for light-emitting diodes (LEDs) due to highly efficient UV emission resulting from its large band gap of 3.37 eV, large exciton binding energy of 60 meV, and low power threshold for optical pumping at room temperature. For the realization of LEDs, both n-type ZnO and p-type ZnO are required. Now, n-type ZnO for practical applications is available; however, p-type ZnO still has many drawbacks. In this study, ZnO films were grown on glass substrates by using atomic layer deposition (ALD) and the ZnO films were irradiated by nitrogen ion beams (20 keV, $10^{13}{\sim}10^{15}ions/cm^2$). The effects of nitrogen-beam irradiation on the ZnO structure as well as the electrical property were investigated by using fieldemission scanning electron microscopy (FESEM) and Hall-effect measurement.

• Journal of the Korean Society for Heat Treatment
• /
• v.25 no.3
• /
• pp.134-137
• /
• 2012

We have considered the effect of electron irradiation energy of 300, 600 and 900 eV on structural, electrical and optical properties of $In_2O_3$ films prepared with RF magnetron sputtering. In this study, the thin film crystallization, optical transmittance and sheet resistance are dependent on the electron's irradiation energy. The electron irradiated $In_2O_3$ films at 900 eV are grown as a hexagonal wurtzite phase. The sheet resistance decreases with a increase in electron irradiation energy and $In_2O_3$ film irradiated at 900 eV shows the lowest sheet resistance of $110{\Omega}/{\Box}$. The optical transmittance of $In_2O_3$ films in a visible wave length region also depends on the electron irradiation energy. The film that at 900 eV shows the higher figure of merit than another films prepared in this study.

• Bulletin of the Korean Chemical Society
• /
• v.31 no.1
• /
• pp.112-115
• /
• 2010

Transparent conducting undoped and Al impurity doped ZnO films were deposited on glass substrate by spin coat technique using 24 days aged ZnO precursor solution with solution of ethanol and diethanolamine. The films were characterized by UV-Visible spectroscopy, X-ray diffraction (XRD), scanning electron microscope (SEM), electrical resistivity ($\rho$), carrier concentration (n), and hall mobility ($\mu$) measurements. XRD data show that the deposited film shows polycrystalline nature with hexagonal wurtzite structure with preferential orientation along (002) crystal plane. The SEM images show that surface morphology, porosity and grain sizes are affected by doping concentration. The Al doped samples show high transmittance and better resistivity. With increasing Al concentration only mild change in optical band gap is observed. Optical properties are not affected by aging of parent solution. A lowest resistivity ($8.5 \times 10^{-2}$ ohm cm) is observed at 2 atomic percent (at.%) Al. With further increase in Al concentration, the resistivity started to increase significantly. The decrease resistivity with increasing Al concentration can be attributed to increase in both carrier concentration and hall mobility.

• Proceedings of the Plant Resources Society of Korea Conference
• /
• 2018.04a
• /
• pp.93-93
• /
• 2018

This study disclosed the aqueous fruits extract of Rubus coreanus as a sustainable agent for the synthesis of Rubus coreanus zinc oxide nanoparticle (Rc-ZnO Nps) using as a reducing and capping precursor for co-precipitation method. The development of Rc-ZnO was assured by white precipitated powder and analyzed by spectroscopic and analytical instruments. The UV-visible (UV-Vis) studies indicate the maximum absorbance at 357nm which confirmed the formation of ZnO Nps and the purity, functional group and monodispersity were assured by field emission transmission electron microscopy (FE-TEM), Fourier Transform Infrared (FTIR) Spectroscopy and dynamic light scattering (DLS). The X-ray powder diffraction (XRD) data revealed the Nps is 23.16 nm in size, crystalline in nature and possess hexagonal wurtzite structure. The Rc-ZnO Nps were subjected for catalytic studies. The Malachite Green dye was degraded by Rc- ZnO NPs in both dark and light (100 W tungsten) conditions and it degraded about 90% at 4 hours observation in both cases. The biodegradable, low cost Rc-ZnO NPs can be a better weapon for waste water treatment.