• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.23 no.6
• /
• pp.413-420
• /
• 2011

Thermodynamic cycles using binary mixtures as working fluids offer a high potential for utilization of low-temperature heat sources. This paper presents a thermodynamic performance analysis of Goswami cycle which was recently suggested to produce power and cooling simultaneously and combines the Rankine cycle and absorption refrigeration cycle by using ammoniawater mixture as working fluid. Effects of the system parameters such as concentration of ammonia and turbine inlet pressure on the system are parametrically investigated. Results show that refrigeration capacity or thermal efficiency has an optimum value with respect to ammonia concentration as well as to turbine inlet pressure.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.12
• /
• pp.1277-1282
• /
• 2004

ITO films on PET substrate were prepared by DC magnetron sputtering method using powdery target with different deposition conditions. In addition, the electrical and optical properties were investigated. As the sputtering power and working pressure were higher, the resistvity of ITO films increased. The optical transmittance deteriorated with increasing sputtering power and thickness. As the working pressure increased, however, the optical transmittance improved at visible region of light. From these results, we could deposited ITO films with 8${\times}$10$^{-3}$ $\Omega$-cm of resistivity and 80 % of transmittance at optimal conditions.

• Proceedings of the KSME Conference
• /
• 2000.11b
• /
• pp.222-227
• /
• 2000

At representative thermoeconomic theory to determine the unit cost of multiple products, there are the $\ulcorner$SPECO$\lrcorner$ method of Tsatsaronis's study group and the $\ulcorner$MOPSA$\lrcorner$ method of chung-ang university phase laboratory. Against this theory, we propose new theory called $\ulcorner$Thermoeconomics to divide the exergetic cost into each working fluid$\lrcorner$ in this study. Also, we apply new thermoeconomic theory to CGAM problem (30MW-grade imaginary gas turbine cogeneration power plant) that it is representative power system in thermoeconomics theory, and we fixed to interpreted the unit cost of electricity on the part of gas turbine and the unit cost of steam exergy(enthalpy) on the part of HRSG.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.342.2-342.2
• /
• 2014

IZO, ITO, ITO 등의 투명전극들 중 Indium Tin Oxide (ITO) 다른 전극에 비해 높은 광투과도와 낮은 저항으로 인하여 다양한 부분에서 널리 이용되고 있다. 본 연구에서는 우수한 투과도의 멀티 layer 단열 창호를 위한 film 개발을 위해 RF magnetron system을 이용하여 Sodalime Glass와 polyethylene terephthalate (PET) substrate에 ITO를 증착함으로써 전기적 광학적 특성을 조사하였다. 실험은 power 변화와 Ar, O2의 가스 분압비, Working Pressure의 변화를 변수로 두어 진행하였다. 측정은 Ellipsometry를 이용하여 광학적인 두께와 굴절률을 조사하였고 UV visible spectrometer를 통해 광학적인 투과도를 확인하였다. Power는 100 Watt 늘려가며 진행하였고 O2 유량의 변화에 따라 투과도와 면저항, 굴절률 특성이 달라짐을 확인할 수 있었다. O2의 유량에 따라 면저항이 줄어들다가 어느 정도 이상이 되면 급격히 증가함을 확인할 수 있었다. Working Pressure 변화에 따른 전기적 광학적 특성 또한 확인 하였다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.341.2-341.2
• /
• 2014

산화물 반도체는 가시광선 영역인 380~780 nm 부근에서의 투과율이 80% 이상이고, 3.2 eV 이상의 band gap과 높은 mobility를 가지는 물질로서 투명한 스마트 창호필름이나 디스플레이에 유망한 물질로 연구되고 있다. 본 연구에서는 스마트 윈도우에 적용되는 높은 가시광 투과율과 적외선 차단을 위한 필름개발을 목적으로 산화물 반도체인 $TiO_2$ 물질을 RF Sputter를 이용하여 상온에서 박막성장을 하였다. Glass와 PET 위에 동시에 성장시켜 각각의 기판에 성장된 $TiO_2$ 박막의 물리적인 성질 등을 조사하였다. 측정은 Ellipsometry를 이용하여 광학적인 두께와 굴절률을 조사하였고 UV visible spectrometer를 통해 광학적인 투과도를 확인하였다. 100Watt 부터 RF power를 높여가며 Working Pressure 변화변 주었을 때 낮은 RF power와 Working Pressure에서 높은 가시광 투과율을 확인 할 수 있었다.

• International Journal of Precision Engineering and Manufacturing
• /
• v.9 no.2
• /
• pp.39-43
• /
• 2008

Atmospheric pressure plasma polishing (APPP) is a noncontact precision machining technology that uses low temperature plasma chemical reactions to perform atom-scale material removal. APPP is a complicated process, which is affected by many factors. Through a preliminary theoretical analysis and simulation, we confirmed that some of the key factors are the radio frequency (RF) power, the working distance, and the gas ratio. We studied the influence of the RF power and gas ratio on the removal rate using atomic emission spectroscopy, and determined the removal profiles in actual operation using a commercial form talysurf. The experimental results agreed closely with the theoretical simulations and confirmed the effect of the working distance. Finally, we determined the element compositions of the machined surfaces under different gas ratios using X-ray photoelectron spectroscopy to study the influence of the gas ratio in more detail. We achieved a surface roughness of Ra 0.6 nm on silicon wafers with a peak removal rate of approximately 32 $mm^{3}$/min.

• Journal of Radiation Protection and Research
• /
• v.39 no.2
• /
• pp.103-108
• /
• 2014

Following the emergency work in Fukushima Daiichi nuclear power plant, more attention was paid for the radiation protection of workers working under severe accident condition. The protection procedure for the emergency workers, including the on-site emergency center, the seismic isolated building and the reestablishment of the radiation protection framework were analyzed to investigate drawbacks and deficiencies which led to adverse effects on the emergency planning and on emergency workers' health and comfort. Those drawbacks were identified and studied, and then suggestions were made to enhance the emergency working condition to avoid any future problems during severe accident emergency work and management.

• Transactions of The Korea Fluid Power Systems Society
• /
• v.6 no.4
• /
• pp.9-15
• /
• 2009

Hydraulic excavators are the representative of field robot and have been used in various fields of construction. Since the excavator operates in the hazardous working environment, operators of excavator are exposed in harmful environment. Therefore, the hydraulic excavator automation and remote operation system has been investigated to protect from the hazardous working environment. In this paper, remote operation excavator system is developed using the mini hydraulic excavator and the tracking control system of each links of excavator is designed. To apply the tracking control system, the adaptive sliding mode control algorithm is proposed. It is found that the performance of the proposed control system is improved through experimental results of using the remote operation excavator system.

• 유공압시스템학회:학술대회논문집
• /
• 2010.06a
• /
• pp.62-65
• /
• 2010

Field robot represented by excavator can be applied for various working in manufacturing, construction, agriculture etc. Because of the flexibility of its multi-joint mechanism and the high power of hydraulic actuators. Since the excavator operates in the hazardous working circumstance, operators exposed in harmful environment. Therefore, automation system has been investigated to protect from the harmful environment. In this paper, the method to construct the remote control system is proposed. The remote control system is consisted of a manual and auto mode. Manual mode controls a hydraulic cylinder as open loop control. and auto mode controls the end effecter of excavator using tracking control system. The efficiency of remote control system was evaluated through the field test.

• Proceedings of the KIEE Conference
• /
• 1998.07c
• /
• pp.929-931
• /
• 1998

This paper describes the peak load forecasting technique of distribution transformers with correlation equation. While customers are demanding safe energy supply, conventional correlation equation that is used for load management of distribution transformers in domestic has some problems. To get accurate correlation equation, se-correlation equation were examined using new collected using the measuring instrument dev for this study. It was recognized that the qua equation was the most accurate for peak forecasting from working electrical energy.