• 한국재료학회지
• /
• 제11권11호
• /
• pp.965-971
• /
• 2001

The objective of this study is to investigate the characteristics - microstructure, hardness, adhesive strength and friction coefficient - of the coatings with aging - treatment after optimizing internal- plasma spraying parameters for Al-30wt%Si powder as a basic research to manufacture the cylinder block bore for Al engine composed of Al-30wt%Si alloy on Al alloy, The optimum internal-plasma spraying parameters of Al-30wt%Si alloy are summarized as follows: voltage: 37.5V, current: 160A, working distance: 25mm, gun traverse speed: 4.5mm/s, rotating speed: 518m/min. The primary Si particles grew aggressively with increasing heat-treating temperature. The hardness of the as-sprayed coating was about Hv=275 but this value was abruptly decreased with increasing heat-treating temperature. And average friction coefficient of the coating was below 0.08 after heat treatment for 48h at $175^{\circ}C$.

• Journal of Welding and Joining
• /
• 제15권1호
• /
• pp.116-124
• /
• 1997

A scope of this study is to establish the optimum plasma spray conditions for fine ($5\mu\textrm{m}$) $Al_2O_3$ powder. However, the flowability of the $Al_2O_3$ powder is not so good because of irregular particle shape and fine particle size. Therefore, powder feeding system was modified by 1) change of powder feeding line material from polymer to copper 2) shorten the powder feeding tube length 3) heating the powder feeding system to $80^{\circ}C$4) vibrating the powder feeding line continuously, in order to feed the fine powder homogeneously. The homogeneous powder feeding conditions were obtained with the modified powder feeding system by controlling the powder carrier gas flow and the powder flow rate indicator. The best plasma spraying conditions for the fine $Al_2O_3$ powder were found out as 40kw gun power, 80 g/min. powder feed rate and 50 mm working distance after characterizing the microstructure, hardness and wear loss of the $Al_2O_3$ coating layer.

• 전기학회논문지
• /
• 제64권4호
• /
• pp.567-572
• /
• 2015

Discharge characteristics of linear microwave plasma were investigated by using fluid simulation of 2D axis-symmetry based on finite elements method. The microwave power was 2.45 GHz TEM mode and transmitted through linear antenna. Resistive power and pressure were considered simulation variables and argon was used for working gas. A decrease of electron density along the quartz tube was observed in low power condition but relatively uniform plasmas were generated in chamber by increasing the resistive power. The electron temperature was highly detected near the surface of quartz tube because the electron was heated only dielectric surface. The power transmission efficiency decreased and characteristics of surface plasma were observed in high electron density condition.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2003년도 추계학술발표회초록집
• /
• pp.54-54
• /
• 2003

DLC films were deposited on Si(100) substrates by inductively coupled plasma (ICP) assisted chemical vapor deposition (CVD). A mixture of acetylene (C$_2$H$_2$) and argon (Ar) gases was used as the precursor and plasma source, respectively. The structure of the films was characterized by the Raman spectroscopy. Results from the Raman spectroscopy analysis indicated that the property change of the DLC films is due to the sp$^3$ and sp$^2$ ratio in the films under various conditions such as ICP power, working pressure and RF substrate bias. The hydrogen content in the DLC films was determined by an electron recoil detector (ERB). The roughness of the films was measured by atomic force microscope (Am). A microhardness tester was used for the hardness and elastic modulus measurement. The DLC film showed a maximum hardness of 37㎬. In this work, the relationship between deposition parameters and mechanical properties were discussed.

• Journal of Pharmaceutical Investigation
• /
• 제22권4호
• /
• pp.289-300
• /
• 1992

The counter-transport phenomena in the hepatic transport of 1-anilino-8-naphthalene sulfonate (ANS) were kinetically investigated by analyzing the plasma disappearance-time profiles and the transport into the isolated hepatocytes. In vivo "counter transport phenomena" were simulated based on the perfusion model which incorporated the carrier-mediated transport and the saturable intracellular binding. The condition that the mobility of carrier-ligand complex is greater than that of free carrier is not essential for the occurrence of counter-transport phenomenon. To examine the inhibitory effects on the initial uptake of a ligand by the liver, it is necessary to judge whether the true counter-transport mechanism (trans-stimulation) is working or not. The initial plasma disappearance curves of ANS were then kinetically analyzed based on a two-compartment model, in which the ligand is eliminated only from the peripheral compartment (liver compartment). No effects on the initial plasma disappearance rates of ANS were observed after preloading of bromophenol blue (BPB) or rose bengal (RB) in the liver. Inhibitory effect of BPB or RB on the initial uptake (or efflux) rates of ANS by the isolated hepatocytes were not observed, suggesting that the true counter transport mechanism is not working. In conclusion, checking the preloading effects of transstimulation on the initial uptake of a ligand by the liver could be a useful criterion for carrier cycling and common use of the same carrier between two ligands. However, one cannot exclude those possibilities even if the preloading effects cannot be observed.

• 한국태양에너지학회 논문집
• /
• 제33권2호
• /
• pp.11-17
• /
• 2013

Silicon nitride($SiN_x:H$) deposited by radio frequency plasma enhanced chemical vapor deposition(RF-PECVD) is commonly used for anti-reflection coating and passivation in crystalline silicon solar cell fabrication. In this paper, characteristics of the deposited silicon nitride was studied with change of working pressure, deposition temperature, gas ratio of $NH_3$ and $SiH_4$, and RF power during deposition. The deposition rate, refractive index and effective lifetime were analyzed. The (100) p-type silicon wafers with one-side polished, $660-690{\mu}m$, and resistivity $1-10{\Omega}{\cdot}cm$ were used. As a result, when the working pressure increased, the deposition rate of SiNx was increased while the effective life time for the $SiN_x$-deposited wafer was decreased. The result regarding deposition temperature, gas ratio and RF power changes would be explained in detail below. In this paper, the optimized condition in silicon nitride deposition for silicon solar cell was obtained as 1.0 Torr for the working pressure, $400^{\circ}C$ for deposition temperature, 500 W for RF power and 0.88 for $NH_3/SiH_4$ gas ratio. The silicon nitride layer deposited in this condition showed the effective life time of > $1400{\mu}s$ and the surface recombination rate of 25 cm/s. The crystalline silicon solar cell fabricated with this SiNx coating showed 18.1% conversion efficiency.

• 한국진공학회지
• /
• 제10권2호
• /
• pp.194-200
• /
• 2001

13.56 MHz rf플라즈마를 이용하여 증착된 DLC(diamond-like carbon) 박막의 광학적 특성에 대해 조사하였다. $CH_4$가스를 원료가스로 하여 PECVD법에 의해 DLC 박막을 형성하였으며 이때 RF power, working pressure, 보조가스의 종류 및 양에 따른 투과도(transmittance)와 optical band gap의 변화를 관찰하였다. RF power가 증가하고 working pressure가 높을수록 optical band gap이 감소하는 결과를 얻을 수 있었고. FT-IR분석을 이용하여 탄소-수소 결합 양을 관찰함으로써 DLC 박막의 결합구조 변화를 증명할 수 있었다. 그리고 수소와 질소를 첨가한 경우 증착시 탄소-수소 결합을 끊는 역할을 하여 optical band gap이 감소하는 결과를 얻을 수 있었다.

• 청정기술
• /
• 제7권3호
• /
• pp.203-214
• /
• 2001

플라즈마를 발생시키는 반응기체의 종류에 따라 실리콘 산화막 세정에 어떠한 영향을 미치는지에 대해 연구하였다. 압력 (100 mTorr), 전력 (300 W, 500 W), 전극간 거리 (5, 8, 11.5 cm), 세정시간 (90초, 180초), 가스유량 (50sccm) 등의 변수들을 고정시키고 $CHF_3$, $CF_4$, 아르곤, 산소 등의 세정가스를 변화시키며 세정성능을 비교하였다. 세정결과 아르곤 플라즈마는 단지 물리적인 스퍼터링 효과만으로 세정속도가 느렸다. 산소 플라즈마는 5cm 전극거리, 300W, 180초 세정시 좋은 세정효과를 내었으나, 표면거칠기가 증가하였다. $CF_4$ 플라즈마의 경우 가장 좋은 세정효과를 얻었다. $CHF_3$ 플라즈마는 CFx/F의 비율을 낮출 수 있는 첨가기체가 필요함을 알 수 있었다. $CHF_3$에 아르곤을 첨가하였을 경우에는 원활한 세정효과를 얻을 수 없었으나, 산소를 첨가하였을 경우 좋은 세정효과를 얻을 수 있었다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2012년도 제38회 춘계학술대회논문집
• /
• pp.545-550
• /
• 2012

고에너지 금속 분말은 높은 용융점을 가진 산화피막의 점화방해 효과로 인해 점화가 용이하지 않다. 따라서 점화를 위해서는 단시간에 높은 온도의 열적 공간을 형성할 수 있는 점화원이 필요하며 스팀 플라즈마 점화원은 탄화수소 계열의 점화원, 수소-산소 점화원, 레이져 점화원과 다르게 짧은 시간에 안정적으로 5,000 K 이상의 열적 공간을 형성할 수 있다. 또한 스팀을 작동가스로 사용하므로 친환경적이며 경제적이다. 따라서 본 연구는 스팀 플라즈마 점화기를 연소 시스템에 적용하기 위한 기초 연구로서 방출 분광법을 사용하여 플라즈마의 온도 분포 및 화학종을 분석하였으며, 연소시스템에 적용하여 금속 분말의 점화를 가시적으로 확인하였다.

• Journal of Korean Vacuum Science & Technology
• /
• 제6권2호
• /
• pp.62-66
• /
• 2002

Hydraulic pumps are used to control the landing wheels of aircrafts, and their proper operation is vital to plane safety It is well hewn that adhesive wear failure is a major cause of pump failure. A dual nitrogen plasma immersion ion implantation process calling for the implantation of nitrogen at two different energies and doses has been developed to enhance the surface properties of the disks in the pumps. The procedures meet the strict temperature requirement of <200$^{\circ}C$, and after the treatment, the working lifetime of the pumps increases by more than a factor of two. This experimental protocol has been adopted by the hydraulic pump factory as a standard manufacturing procedure.