• Proceedings of the Korea Concrete Institute Conference
• /
• 1996.10a
• /
• pp.140-147
• /
• 1996

This study was performed to investigate the characteristics of workability and strength of the concrete containing admixtures such as silica fume, fly ash, blast furnace slag, and rice husk ash. For this purpose, the workability and the strength of the concrete containing each admixture were tested and analyzed according to the unit weight of binder and the replacement ratio of each admixture.

• Advances in concrete construction
• /
• v.6 no.2
• /
• pp.103-121
• /
• 2018

This paper reports the effects of coarse and fine recycled concrete aggregates (RCA) on fresh and hardened properties of self-compacting concrete (SCC) containing ground granulated blast-furnace slag (GGBFS) as cement replacement. For this purpose, three SCC mixes groups, were produced at a constant water to binder ratio of 0.38. Both fine and coarse recycled aggregates were used as natural aggregates (NA) replacement at different substitution levels of 0%, 25%, 50%, 75% and 100% by volume for each mix group. Each group, included 0, 15% or 30% GGBFS as Portland cement replacement by weight. The SCC properties investigated were self-compactability parameters (i.e., slump flow, T500 time, V-funnel flow time, L-box passing ability and sieve stability), compressive strength, capillary water absorption and water penetration depth. The results show that the combined use of RCA with GGBFS had a significant effect on fresh and hardened SCC mixes. The addition of both fine and coarse recycled aggregates as a substitution up to 50% of natural aggregates enhance the workability of SCC mixes, whereas the addition from 50 to 100% decreases the workability, whatever the slag content used as cement replacement. An enhancement of workability of SCC mixes with recycled aggregates was noticed as increasing GGBFS from 0 to 30%. RCA content of 25% to 50% as NA replacement and cement replacement of 15% GGBFS seems to be the optimum level to produce satisfactory SCC without any bleeding or segregation. Furthermore, the addition of slag to recycled concrete aggregates of SCC mixes reduces strength losses at the long term (56 and 90 days). However, a decrease in the capillary water absorption and water permeability depth was noticed, when using RCA mixes with slag.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.20 no.6
• /
• pp.40-45
• /
• 2016

It should be noted that the use of the lathe scrap for making fiber reinforced cementitious composites raised friendly environmental effect as well as economy because the lathe scrap is a by-product of steel manefactures and is occurred when lathe and milling works of them are conducted to process steel manufactures. Thus, the purpose of this experimental research is to investigate workability and strength characteristics of lathe scrap reinforced cementitious composites(LSRCCs). For this purpose, three types of lathe scraps were collected from processing plants of metal, and then LSRCCs containing these were made for 2mm width and 40mm length. As a result, it was observed from the test results that the workability of LSRCCs was slightly decreased than plain mortar and the flexural strength of LSRCCs were much larger than these of plain mortar and effect of types of lathe scrap on the characteristics of LSRCCs were somewhat large.

• Journal of Conservation Science
• /
• v.32 no.2
• /
• pp.261-271
• /
• 2016

We have investigated relationship between particle characteristics of oyster shell powder pigments and their performance such as workability and durability. Three types of the powder which have different particle size and shape(spherical, elliptical, columnar and irregular) distributions were made for this study and we evaluated spreadability and uniformity for workability, and adhesion and surface hardness for durability of painted films by each powder paints. As a result, we found out that the workability and durability of the paints were influenced by the particle shape distribution more than the particle size distribution. The durability, especially, was enhanced as the ratio of columnar particles in the powders was increased. This result verifying the important factor affecting the durability can be base data for selecting oyster shell white paint and assessing its quality for conservation and restoration of Dancheong, as well as to produce high quality traditional paints.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.7
• /
• pp.237-244
• /
• 2016

The workability of mortar determines its construction performance in a structure showing its designed resistance to external loads. Measuring the rheological properties of mortar is one way of quantifying its workability, but its field-applications are limited due to economical and spatial issues. The robustness of the slump flow test allows its use for evaluating the workability of mortar, even though it is a rather qualitative test method. This paper proposes a channel flow test and develops a correlation between its result and the rheological properties of mortar. The volume-of-fluid simulation for the channel flow test was accomplished, and a numerical database for the correlation was composed. A correlation model to estimate the rheological properties of mortar using the results of the channel flow test as inputs is proposed.

• Korean Journal of Materials Research
• /
• v.26 no.11
• /
• pp.628-634
• /
• 2016

The cold rolling workability and mechanical properties of two new alloys, designed and cast Al-5.5Mg-2.9Si and Al-7Mg-0.9Zn alloys, were investigated in detail. The two alloy sheets of 4 mm thickness, 30 mm width and 100 mm length were reduced to a thickness of 1 mm by multi-pass rolling at ambient temperature. The rolling workability was better for the Al-7Mg-0.9Zn alloy than for the Al-5.5Mg-2.9Si alloy; in case of the former alloy, edge cracks began to occur at 50% rolling reduction, and their number and length increased with rolling reduction; however, in the latter alloy, the sheets did not have any cracks even at higher rolling reduction. The mechanical properties of tensile strength and elongation were also better in the Al-7Mg-0.9Zn alloy than in Al-5.5Mg-2.9Si alloy. Work hardening ability after cold rolling was also higher in the Al-7Mg-0.9Zn alloy than in the Al-5.5Mg-2.9Si alloy. At the same time, the texture development was very similar for both alloys; typical rolling texture developed in both alloys. These differences in the two alloys can primarily be explained by the existence of precipitates of $Mg_2Si$. It is concluded that the Al-7Mg-0.9Zn alloy is better than the Al-5.5Mg-2.9Si alloy in terms of mechanical properties.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.2 no.1
• /
• pp.40-45
• /
• 2014

Although the accelerators are used at the early stage to control setting-time and strength of concrete when cold-weather concrete is utilized, no security of workability occurs because the early hydration makes them react rapidly. Therefore, the tablet used in previous study is applied in this study. In particular, because a small amount of fly-ash being replaced in cold weather concrete of domestic, fly-ash concrete incorporating the tablet is discussed in workability by elapsed time, early strength to ensure the development of adequate strength, and freezing-thawing resistance. As a result, both 0.5 and 1.0% tablets were found to be superior. Thus, it was verified in cold weather concrete incorporating fly-ash that workability can be secured, as well as the development of early strength to prevent early frost.

• International Journal of Highway Engineering
• /
• v.8 no.4 s.30
• /
• pp.101-113
• /
• 2006

Generally, asphalt binder modifier increases the viscosity at high temperature as well as at mixing and paving temperature, so that higher temperature is required to produce the hot-mix asphalt. Otherwise, wax is able to improve workability by means of decreasing the viscosity of asphalt binder. In this study, the effect of PE wax used to modify the asphalt binder was evaluated in laboratory. The properties of PE wax modified binder were compared with those of SBS and Crumb Rubber Modified binders. The results showed that wax type I has an effect on strengthening rut resistance as well as improving workability. However, wax type I weaken crack resistance due to making binder harder at intermediate temperature. The results also showed that wax type II has an effect on improving workability and on strengthening crack resistance due to making binder softer.

• Resources Recycling
• /
• v.24 no.4
• /
• pp.3-11
• /
• 2015

The negative effects of unburned fabric in municipal solid waste incinerator (MSWI) ash on the performances of cement composite were investigated. The chemical and physical characteristics of MSWI ash powder containing high volume of unburned fabric were analyzed. The workability and compressive strength of mortar-type cement composites with the ash powder were evaluated. The workability of the cement composites was decreased mainly by unburned fabric in the ash, while the compressive strength was decreased by MSWI ash itself. From the experimental results, the critical limits for both MSWI ash and their powder containing unburned fabric in the cement composites should be limited from standpoint of the workability of the composite.

• Journal of the Korea Institute of Building Construction
• /
• v.18 no.3
• /
• pp.235-242
• /
• 2018

The objective of the paper is to investigate the effect of mix designing factors on the workability and rheological parameters of self compacting concrete in order to facilitate the difficulties of quality control of high sensitivity of SCC. Mix proportions of SCC were prepared with various conditions of coarse, and fine aggregate, and unit water content, and the SCC mixtures were tested on workability, rheological properties to provide basic data for quantitative evaluation. Test results indicated that the yield stress of SCC decreased with increasing the coarse aggregate volume ratio, and increased with increasing the amount of VMA. However, unit water content, fine aggregate type, and air content didn't affect the yield stress value. The plastic viscosity according to the mixing factors showed a similar tendency to the yield stress. In addition, there was no correlation between yield stress and workability (flow, T50, V-lot). However, there was closely correlation among plastic viscosity and T50 and V-lot. Especially, T50 and V-lot time decreased with decreasing plastic viscosity.