• Journal of the Korean Society for Heat Treatment
• /
• v.8 no.4
• /
• pp.266-278
• /
• 1995

The high strain-rate dynamic plastic behavior of Fe-X%Mn alloys was investigated. The strain rate did not have an effect when tested under quasi-static strain rates($2{\times}10^{-3}/sec$ and $2{\times}10^{-1}/sec$). However, the true stress increased at all strain levels when the strain rate increased to $6{\times}10^3/sec$. Based on the experimental results, an constitution equation to calculate the dynamic strength for strain rates over $10^4/sec$ was determined. The Fe-5%Mn alloy containing athermal ${\alpha}^{\prime}$ martensite initially did not show work hardening. The work hardening increased with Mn content showing a maximum at 20% Mn. The high work hardening of Fe-20%Mn and Fe-30%Mn alloys appears to be closely related not only to the initial amounts of ${\varepsilon}$ martensite but to the strain induced transformation (${\gamma}{\rightarrow}{\varepsilon}$ and ${\varepsilon}{\rightarrow}{\alpha}^{\prime}$) occurring during each stages of deformation.

• Journal of Preventive Medicine and Public Health
• /
• v.7 no.2
• /
• pp.305-312
• /
• 1974

Studies on 66 industrial accidents happened in a battery manufacturing industry during a year of 1973 were carried out. The results obtained are follows, 1. Majority of employees of this industry was occupied by yong woman aged between 20-24. 2. Incidence rate, frequency rate and severity rate of the accidents was 36.8 per 1,000, 12.8 per 100,000 labour day and 0.3% respectively. Anual average days of lost due to accidents was 18.0 days. 3. Accidents happened more frequently in male than female, and happened most frequently in age between 30-34. 4. As to type of work, 47.9% of the accidents happened on hand operating workers. This was the same in both sex. 5. Accidents happened mainly during 2-3 hours latter from work starts in both morning and afternoon work, 6. 63.6% of the accidents happened on hands in both sexes and followed by lower extremities. 7 Surface wounds like as laceration, cut and abrasion were the main types of injury occupying 31.8% and followed by burn at 24.2%. 8. 54.5% of accidents needed 1-2 weeks to heal the injury and heavy injury needed more than 5 weeks was only 9.1%. 9. Accidents happened most frequently in employees who served between 2-3 years in this industry, but observing of sex difference. it was most frequent in male who served more than 4 years whereas less than 6 months in female.

• Journal of the Ergonomics Society of Korea
• /
• v.29 no.2
• /
• pp.211-216
• /
• 2010

Fire service personnel and ambulance paramedics suffer musculoskeletal disorders as they lift and carry patients while performing Emergency Medical Services (EMS). The objective of the current study was performed to examine the association between working environment and musculoskeletal disorders of 119 paramedics and to analysis the EMS activities for them through basic survey (including task characteristics, risk factors, symptoms and illnesses). Observational job analysis of EMS activities indicated the squatting posture during first-aid performed on floor and the abrupt use of force during carrying heavy load including stretcher with patients on as hazard factors, and excessive low back twisting and bending during stairway transfer was observed. In addition, work-physiological assessment revealed various but rather high lumbar muscle usage rate among the study subjects, being 14.6~32.8% compared with Maximum Voluntary Contraction (MVC) during patients transfer work. Resting heart rate showed 65/min, on the other hand, heart rate on mobilization indicated maximum 124~156/min. Therefore, the results of analysis to the EMS activities, rescuer activities and medical tasks were accompanied with high possibility of accident and musculoskeletal disorders. Also, EMS activities indicated high muscle fatigue and energy consumption, and accumulated muscle fatigue with during continued work.

• Nuclear Engineering and Technology
• /
• v.37 no.2
• /
• pp.201-206
• /
• 2005

Fretting, which is a special type of wear, is defined as small amplitude relative motion along the contacting interface between two materials. The structural integrity of steam generators in nuclear power plants is very much dependent upon the fretting wear characteristics of Inconel 690 U-tubes. In this study, a finite element model that can simulate fretting wear on the secondary side of the steam generator was developed and used for a quantitative investigation of the fretting wear phenomenon. Finite element modeling of elastic contact wear problems was performed to demonstrate the feasibility of applying the finite element method to fretting wear problems. The elastic beam problem, with existing solutions, is treated as a numerical example. By introducing a control parameter s, which scaled up the wear constant and scaled down the cycle numbers, the algorithm was shown to greatly reduce the time required for the analysis. The work rate model was adopted in the wear model. In the three-dimensional finite element analysis, a quarterly symmetric model was used to simulate cross tubes contacting at right angles. The wear constant of Inconel 690 in the work rate model was taken as $K=26.7{\times}10^{-15}\;Pa^{-1}$ from experimental data obtained using a fretting wear test rig with a piezoelectric actuator. The analyses revealed donut-shaped wear along the contacting boundary, which is a typical feature of fretting wear.

• Nuclear Engineering and Technology
• /
• v.18 no.4
• /
• pp.267-272
• /
• 1986

To obtain various necessary data for the manufacturing and the use of the nuclear fuel cladding tube, the effects of deformation and heat treatment on Properties of Zircalof-4 material have been studied. The hardness is increased rapidly at a low degree of cold work and increased rapidly at cold work above 10%. Recrystallization has been completed at 64$0^{\circ}C$, 59$0^{\circ}C$, and 555$^{\circ}C$ in 30%, 60% and 80% cold worked specimen, respectively. The transformation of microstructure with increasing cooling rate after $\beta$-annealing is as follows; coarse Widmanstatten ($\alpha$) longrightarrow fine parallel plate ($\alpha$) longrightarrow martensite ($\alpha$$^{'}$). At the same time, hardness increased with increasing cooling rate. rate.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.29 no.1
• /
• pp.21-26
• /
• 2019

Objective: The aim of this study is to analyze an excess trend for domestic permissible exposure limit of trichloroethylene based on previous literature review. Materials and Methods: The research object is a trichloroethylene among 13 chemical substances regulated with PEL(Permissible Exposure Limit) in Occupational Safety and Health Act. The information utilized from this study is the work environment measurement data from 2004 to 2013. The highest level among concentration data measured at various workplaces was selected as a representative value through data process. N.D. (Not Detected) data was considered as 1/2 of LOD(Limit Of Detection). Results: Among work environment measurement data between 2004 and 2013, the highest number of excess workplace and excess rate(24 sites & 1.15%) was observed in 2008's data when applying the PEL(50 ppm) of trichloroethylene. When they are compared with the ACGIH's TLV-TWA(10 ppm), 2008's data showed the highest number of excess workplace and excess rate(175 sites & 8.37%). The number of excess workplace and excess rate related to PEL of trichloroethylene showed increase trend in 2005 but tended to decrease after 2008. Conclusions: Based on the results obtained from this study, the exposure level of trichloroethylene in case of domestic workers is not considered as a safe phase regardless of the year of work environment measurement year. Thus, a strictly preventive management in workplace should be provided for reducing exposure level of trichloroethylene.

• International Journal of Internet, Broadcasting and Communication
• /
• v.13 no.3
• /
• pp.130-136
• /
• 2021

The purpose of this study was to investigate the effect of the intensity of warm-up exercise on the physiological response and exercise performance during resistance exercise. For this purpose, 8 male college students with at least 1 year of experience in resistance movement were selected. The warm-up condition was set to NON condition (preparatory exercise not performed), 3 set condition, 6 set condition, and 9 set condition, and the intensity was different for each set. After warm-up, 75% 1RM of main exercise was performed, and blood pressure and heart rate were measured immediately after exercise to measure RPP. The number of repetitions and total work for each condition were measured as the number of repetitions and momentum during the main exercise. The measured data were analyzed by repeated measures two-way ANOVA. As a result, although there was no difference in Rate Pressure Product according to the warm-up conditions, the number of repetitions and total amount of exercise showed the highest in the 3-set condition. Therefore, it is thought that the number and intensity of warm-up exercises should be set appropriately during resistance exercise, and warm-up of 3 sets or more during resistance exercise is thought to decrease exercise performance.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.20 no.3
• /
• pp.168-174
• /
• 2010

South Korea's industrial injuries are decreasing overall in the last 32 years. Nevertheless, the fatal occupational injury rate is still higher than in developed countries. This study was conducted to help prevention strategies of occupational injuries for the Republic of Korea. Fatal occupational injury rates were obtained from "Industrial Accident Analysis"of the Korean Ministry of Labor. Poisson regression was used to assess time trends. Socioeconomic indicators were obtained from the Korea Labor Institute and the Statistics Korea. Fatal occupational injury rates were adjusted by year, and Pearson correlation analysis was used to assess the relationship between the socio-economic indicators and occupational injuries. In 1975, fatal occupational injury rate was 54.8 per 100,000 workers. With somewhat up and down, it was decreased to 21.0 in 2006. An annual rate of change for the years 1975-2006 was - 1.83%, and for the years 2002-2006 was -5.02%. As economic growth rate, paricipation rate for the age less than 25 and hours of work per week or year increased, fatal occupational injury rate also increased. Conversely, as GDP per capita, paricipation rate or employment rate for female, paricipation rate for the age 25 or more, hourly compensation costs for production workers and services output as percent of GDP increased, fatal occupational injury rate decreased. By the development of safety techniques and the adoption of more legislative constraints, developed economy reduce occupational injuries. Conversely, economic growth may raise occupational injuries. Therefore, prevention strategies are needed to manage both of them. We need to make an effort to prevent occupational injuries due to not only sexual differences, but also job differences between male and female. Preventive strategies are needed to consider the characteristics of younger workers. Addition to wage, other appropriate variables for work condition should be considered together. Extending work hours is need to be regulated with systemic methods.

• Communications for Statistical Applications and Methods
• /
• v.9 no.3
• /
• pp.649-663
• /
• 2002

We consider an unlimited fluid queueing model which has Fractional Brownian motion(FBM) as an input and a single server of constant service rate. By using the result of Duffield and O'Connell(6), we investigate the asymptotic tail-distribution of the stationary work-load. When there are multiple homogeneous FBM inputs, the workload distribution is similar to that of the queue with one FBM input; whereas for the heterogeneous sources the asymptotic work-load distributions is dominated by the source with the largest Hurst parameter.

• Journal of Welding and Joining
• /
• v.14 no.5
• /
• pp.87-94
• /
• 1996

It has been well known in GMA welding process that wire feeding speed (WFS) or deposition rate increases linealy with the increase of wire extension. In this investigation, however, such an well-known relationship was .reconsidered in terms of contact-tube to work distance (CTWD) instead of wire extension. To verify the proposed relationship between WFS and CTWD, bead-on-plate welding was performed with various CTWDs in the range of 15∼35mm under the condition of near-constant voltage and current As expected, the test results showed an excellent linear relation between WFS and CTWD. Furthermore, the value of the slope turned out to be quite similar to those of previous investigators obtained either theoretically or experimentally through the Precise measurement of electrode extension. Present result also demonstred that the increase of CTWD could be very practical measure for increaring deposition rate without any increase of heat input Depending on the tip recess the practical maximum of CTWD was appeared to be limited somewhere in 25∼30mm mainly due to the entrappment of porocity.