• Journal of the Korean Wood Science and Technology
• /
• v.36 no.6
• /
• pp.13-22
• /
• 2008

Internal voids affecting the mechanical properties of wood composite were classified into two catagories and characteristics of voids were examined according to density variation of strandboard. The void distribution and content of strandboard according to board density were measured by X-ray computed tomography system and analized using image processing software. Prior to investigation, the densities of strandboard were measured by densitometer and the results were showed high correlation with conventional oven drying method. Based on the image analysis conducted on captured images by X-ray tomography, low resolution can be used to capture the macro-voids (between strand) but not the micro-voids (within strands). Intermediate resolution can be used to capture both the macro and the micro-voids and high resolution can be successfully used to capture the majority of the micro-voids. The content of macro-void was measured and content of micro-void was computed by corresponding related equation. The macro-void distribution can be successfully understood and void content can be correctly estimated through the results.

• Journal of the Korean Wood Science and Technology
• /
• v.42 no.6
• /
• pp.708-713
• /
• 2014

Trusses are widely used for wooden houses in the areas where wood construction in generalized for residential housings such as North America, Australian, New Zealand. In Korea, joist and rafter system is generally used because of the production cost, transportation cost and lack of experience required for truss manufacturing. In this study, roof trusses and flat trusses were manufactured by using oriented strand board (OSB) gusset plates for field assembly and tested under bending load to obtain the allowable loads. The allowable load and the actual load of 6m span roof trusses were 10.60 kN and 5.26 kN, respectively, which is regarded to be sufficient for use in construction. The allowable load and the actual load of 6m span floor flat trusses were 7.18 kN and 7.43 kN, respectively. For flat trusses, the allowable load is slightly lower than the actual load but the difference in very small, and it is thought that flat trusses can be used for construction by applying small change of structures and members.

• Journal of the Korean Wood Science and Technology
• /
• v.42 no.6
• /
• pp.714-722
• /
• 2014

In the previous study, a variety of wood-based panels was thermally decomposed to manufacture carbonized boards that had been proved to be high abilities of insect and fungi repellence, corrosion and fire resistant, electronic shielding, and formaldehyde adsorption as well as sound absorption performance. Based on the previous study, carbonized medium density fiberboard (c-MDF) was chosen to improve sound absorption performance by holing and sanding process. Three different types of holes (cross shape, square shape, and line) with three different sanding thickness (1, 2, and 3 mm) were applied on c-MDF and then determined sound absorption coefficient (SAC). The control c-MDF without holes had 14% of SAC, however, those c-MDFs with holes had 16.01% (square shape), 15.68% (cross shape), and 14.25% (line) of SAC. Therefore, making holes on the c-MDF did not significantly affect on the SAC. As the degree of sanding increased, the SAC of c-MDF increased approximately 65% on sanding treated c-MDFs (21.5, 21.83, and 19.37%, respectively) compared to the control c-MDF (13%). Based on these results, composite sound absorbing panel was developed with c-MDF and MDF (11 mm). The noise reduction coefficient of composite sound absorbing panel was 0.45 which was high enough to certify as sound absorbing material.

• Journal of the Korea Furniture Society
• /
• v.28 no.2
• /
• pp.126-134
• /
• 2017

This study explores PyeongSang, a piece of traditional Korean furniture, in order to make people know the details about what the piece is in the first paper. And based on the paper, PyeongSang will be developed as moulded multi-useful beds and sofas adapting the joint and ornament from the structure and pattern of the piece in the next paper. As the result, it appeared as two styles such as bed types mentioned as SalPyeongSang and ttulmaru in Korean. The pieces have been used from the three Kingdoms period in Korean history. The styles appeared as the structure of four parts with the lower fences called as nangan, the seats jointed by thin wood pieces, the wind hole, and the legs of foot types. The parts were beautifully carved with the ornament such as lattice patterns like geokjamun and manjamun, flower patterns like dangchomun, elephant eyes patterns like ansangmun from the Korean tradition. And the legs showed various shapes such as supports transformed from horse foots, tiger legs and bamboo, and board types carved with elephant eyes and geometric patterns. Hence, in the next paper based on this paper, PyeongSang will be developed as moulded multi-useful beds and sofas adapting the joints and ornaments from the structure and patterns of the piece.

• Journal of Korea Foresty Energy
• /
• v.20 no.2
• /
• pp.9-19
• /
• 2001

This study was carried out to investigate natural insectifuge materials from tree extractives in order to substitute for organic synthetic insecticides for food wrapping corrugated board. Tree samples were collected, extracted, fractionated with hexane, $CH_2Cl_2$, ethylacetate(EtOAc) and $H_2O$, and then freezed dried for further study. EtOAc or $H_2O$ fractions were chromatographed on a Sephadex LH-20 column for isolation and purification, and the isolated compounds were characterized by spectroscopic tools such as NMR and MS. Crude extractives of EtOAc and $H_2O$ fractions were added to the printing ink for corrugated board with the concentration of 2% or 3% based on the weight of the ink, then the prepared ink was printed on the corrugated board to be used for evasion test using larva of indian meal moth(Plodia interpunctella(Hubner)). Robtin, dihydrorobinetin and leucorobinetinidin were isolated from the wood extractives of black locust(Robinia pseudoacacia) and the bark of poplar(Populus alba $\times$ glandulosa) contained many kinds of compounds such as (+)-catechin, naringenin, aromadendrin, eriodictyol, sakuranetin and its glycoside, taxifolin, neosaturanin, salireposide, p-coumaric acid and aesculin. Much of (+)-catechin was isolated from the bark extractives of willow(Salix koreensis) in addition to (+)-gallocatechin and p-coumaric acid and the bark of weeping willow(Salix babylonica) also contained (+)-catechin, (+)-gallocatechin, dihydromyricetin and myricetin.

• The Journal of the Acoustical Society of Korea
• /
• v.28 no.8
• /
• pp.781-789
• /
• 2009

The absorption coefficients of the materials used in a 1:50 scale model multipurpose hall were measured based on ISO 354 and related laws. The shape and materials for the scale model were evaluated based on reflective surfaces, variable acoustic elements and sound-absorbing quality (125Hz-1kHz average) of seats. The measured average absorption coefficients of audience seats, audience and orchestra were 0.64, 0.74 and 0,45, respectively, which were simulated with the combination of wood, absorption materials and foam board. Various mounting methods for absorption curtain and banner were considered according to the installation methods. The average absorption coefficient was measured as 0.42, 0.47 and 0.45 in the conditions of Type A mounting, E mounting with 0.9 m backing air cavity, and Type G mounting which is suspended at the ceiling, respectively. It was confirmed that the absorption coefficient was increased at low frequency by backing air gap. The finishing material of stage house was an absorption material covered with thin fabric, which aimed average absorption coefficient of 0.68 by using fiber glass board. Each part of the real materials was compared with those of 1:50 scale model and it was found that the absorption characteristics of both cases were similar.

• Journal of Korean Society of Steel Construction
• /
• v.15 no.2
• /
• pp.109-116
• /
• 2003

An investigation on the structural behavior of cold-formed steel lipped C-section stud for interior walls or partitions was carried out. This experimental research was carried out to study the ultimate and service load capacity of stud assemblies that are subjected to lateral loads. Each test specimen consisted of three or four lipped C-section studs and two C-section tracks that restrained both ends. The major factors considered in this experiment were the perforation on the web, the connection of the bridge channel and the special clip. The effect of the plaster board and the ply wood, which were attached to the tension flange on the flexural strength, was also investigated. Thereafter, the test strength capacities were compared with the nominal strength, based on the AISI Specifications (1996).

• Journal of the Korean Wood Science and Technology
• /
• v.45 no.5
• /
• pp.580-587
• /
• 2017

Woodfiber insulation board can be considered as a one of the key material for low energy consumption, comfortable and safety construction of residential space because of its eco-friendly and high thermal insulation performance. This study was carried out to investigate the formaldehyde (HCHO) total volatile organic compounds (TVOC) emission properties and combustion shapes by flame test of low density fiberboards (LDFs) prepared with different adhesives. HCHO TVOC emission and combustion properties of LDFs prepared by melamine urea formaldehyde (MUF), phenol formaldehyde (PF), emulsified methylene diphenyl diisocyanate (eMDI) and latex resin adhesives were measured by desiccator method, 20 L chamber method, and flame test, respectively. As results, LDFs manufactured by MUF, eMDI and latex resin adhesives satisfied the Super $E_0$ grade of HCHO emission performance except PF resin. Furthermore, TVOC emission of all LDFs were satisfied the Korean indoor air quality standard (below $400{\mu}g/m^2{\cdot}h$). Especially, LDF with eMDI resin adhesive showed the lowest HCHO and TVOC emissivity, that $0.14mg/{\ell}$, $12{\mu}g/m^2{\cdot}h$, respectively. However, eMDI emitted the small amount ($3{\mu}g/m^2{\cdot}h$) of toluene in VOC components. In the flame test, LDF with MUF resin adhesives showed the most favorable shape after flame test compare to LDFs prepared other adhesives. Based on HCHO and TVOC emission, and combustion shapes, MUF resin adhesive may be recommended to prepare LDF for insulation purpose.

• Korean Journal of Soil Science and Fertilizer
• /
• v.48 no.6
• /
• pp.736-743
• /
• 2015

Organic matter plays important roles in soil ecosystem in terms of carbon and nitrogen cycles. Due to recent concerns on climate change, carbon sequestration in agricultural land has become one of the most interesting and debating issues. It is necessary to understand behavior of soil carbon for evaluating decomposition or sequestration of organic matter and analyzing potential carbon decomposition pattern about the kinds of organic matter sources to cope with well. In order to evaluate decomposition of soil carbon according to organic material during cultivating rice in paddy field, we treated organic material such as hairy vetch, rice straw, oil cake fertilizer, and manure compost at $50{\times}50{\times}20cm$ blocks made of wood board, and analyzed carbon contents of fulvic acid and humic acid fraction, and total carbon periodically in 2013 and 2014. Soil sampling was conducted on monthly basis. Four Kinds of organic matter were mixed with soil in treatment plots on 2 weeks before transplanting of rice. The treatment of animal compost showed the highest changes of total carbon, which showed $7.9gkg^{-1}$ in May 2013 to $11.6gkg^{-1}$ in October 2014. Fulvic acid fraction which is considered to easily decompose ranged from 1 to $2gkg^{-1}$. Humic acid fraction was changed between 1 to $3gkg^{-1}$ in all treatments until organic material had been applied in 2014. From May to August in the second year, the contents of humic acid fraction increased to about $4gkg^{-1}$. The average of humic fraction carbon at treatments of animal compost was recorded highest among treatments during two years, $2.1gkg^{-1}$. The treatment of animal compost has showed the lowest ratio of fulvic acid fraction, humic acid fraction compared with other treatments. The average ratio of fulvic fraction carbon in soil ranged from 16 to 20%, and humic fraction carbon ranged from 19 to 22%. In conclusion, animal compost including wood as bulking agent is superior in sequestrating carbon at agricultural land to other kinds of raw plant residue.

• Fire Science and Engineering
• /
• v.33 no.1
• /
• pp.76-84
• /
• 2019

Experimental studies using an open cone calorimeter were conducted to provide information on the CO and soot yields of wood combustibles required for a kitchen fire simulation of PBD. A total of eight specimens were examined for medium density fiberboard (MDF) and particle board (PB), which are used widely in kitchen furniture production, depending on the water content, surface processing method, and surface color. The thermal penetration time related to the fire spread rate in the depth direction differed significantly according to the surface processing treatment method, even for a specimen of identical thickness. The CO yield ($y_{CO}$) of the MDF and PB series did not change significantly according to the combustion mode and surface treatment process in flaming mode. On the other hand, $y_{CO}$ was approximately 10 times higher in smoldering mode than in flaming mode. The soot yield ($y_{soot}$), however, varied considerably depending on the combustion mode and surface treatment process. In particular, a higher $y_{soot}$ was found in flaming mode and in the surface-treated specimens. Finally, the $y_{CO}$ and $y_{soot}$ of MDF and PB measured for the kitchen fire simulation of PBD were applied.