• Proceedings of the Korean Institute Of Construction Engineering and Management
• /
• 2008.11a
• /
• pp.914-917
• /
• 2008

This paper was to discuss the case and cause of debonding defect of wood floor board in apartment house by investigating actual survey. Most frequent defect in wood floor board was debonding of floor board. Scratch, gap and crack of floor board were also found in floor board installment work. Causes of debonding of floor board is shrinkage of cement mortar beneath floor board and expansion of floor board. Haste in floor board work did not provide enough time to dry cement mortar fully, which led to continue to dry after the installment of floor board. It caused moisture movement toward wood floor board. Accordingly, Before floor board work, careful consideration on moisture condition of cement mortar and enough curing time to eliminate the effect of moisture are taken into.

• Journal of agriculture & life science
• /
• v.46 no.1
• /
• pp.29-34
• /
• 2012

To examine possibilities to make use of woodceramics for the lower material of hot-floored ondol boards, woodceramics made from sawdust board with Pinus densiflora, put them in a wood frame and concrete block and heated them sending an electric current, and measured changes in surface temperature of a laminated floor board and a plywood floor board. As the sending an electric current to time passed, their surface temperature increased rapidly up to 20 minutes, and then gradually ascended. In terms of the surface temperature in the wood frame, the beginning temperature of a plywood floor board was higher than that of laminated floor one; however, as time passed, a laminated floor board's temperature rose, and after 60 minutes, it showed similar to the temperature of a floor board of lamination. On the other hand, the surface temperature in a concrete block showed that the laminated floor board was higher than the plywood floor board in both early and 60-minute later temperatures. With the lapse of time after switching off, the surface temperature of floor boards slowly dwindled up to 9 minutes, and from that time on, began to drop sharply. In terms of the descent speed of surface temperature, when woodceramics' surface temperature was adjusted at $70^{\circ}C$, the laminated floor board was the highest; when it was at $80^{\circ}C$, the plywood floor board was the highest, resulting in rapid descent speed of heat.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.18 no.1
• /
• pp.24-30
• /
• 2019

The deck floor of a the cargo truck becomesis damaged and aged due to the continuous loading of the loading cargo and external environmental factors. Floor boards made of wood and metal are often used. In the case of wood, the cost is high due to the use of imported wood, and the strength is easily deterioratesd due to environmental factors. In the case of metal materials, the durability is higher than that of wood, but problems are raised due to the effect of major factors that hinder the weight reduction, and the effects of corrosion. In order to replace this stucturestructural design, this study proposed a wood fiber composite using natural raw materials. Woody composites are being used as environmentally and friendly exterior materials with the combined advantages of plastic, and wood,; low cost and low density. However, due to the nature of the woody composites, the properties are differentdiffer depending on the contents of the matrix, reinforcing agent, additives, compatibilizer, etc. In this study, we investigate these problems through analysis of the microstructure and mechanical properties according to proper content and injection molding conditions. As a result, it is considered that the wood deck composite can replaced the current Deck Floor Boardreplace current deck floor boards through continuous continued research and results of this study.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.12 no.8
• /
• pp.573-580
• /
• 2002

Generally the ceiling frame of apartment house is made of wood. But the wood frame has several problems due to the natural properties such as distortion by shrink, low fire resistance and material loss in the construction field. And it has some defections in sound insulation performance. Therefore it is necessary to develop a new method that can be used as a ceiling frame. This study aims to analyze and to compare the sound insulation characteristics against the floor impact sound between wood ceiling frame and M-bar frame which is made of steel. The results of this study are like these. M-bar frame is more effective than wood ceiling frame in sound insulation. And sound absorbing or sound insulation materials which can be Put on gypsum board are helpful to improve floor impact sound insulation performance.

• Journal of the Korean Wood Science and Technology
• /
• v.25 no.4
• /
• pp.29-38
• /
• 1997

The effect and control of wood property of reconstituted composite panels for improved board properties by wood-waste materials and development of combination method for heterogeneous materials have been of interest to the wood science researchers. The purpose of this study is to consider the properties in relation to hot pressing conditions and to develope the optimum hot pressing condition with waste wood and waste tire for the manufacturing of composite boards. The study of composite boards for recycling of wood and waste tire is nothing up to the present. Physical and mechanical properties such as specific gravity, moisture content, swelling coefficient, modulus of rupture and modulus of elasticity in bending test were studied. The condition of 3-stage press time for the lowest moisture content of composite board was $4{\rightarrow}3{\rightarrow}3$ minutes. Specific gravity of composite panels was affected mainly by the amount of rubber chip. Because of the low rigidity and high elasticity in rubber chip, it is considered the composite panel was adequate material in the place of compression load, but not bending load. Therefore, it was concluded that a use of rubber-based wood composite panel is proper to the interior materials such as floor a room than exterior materials. From the test results, the most optimum hot pressing conditions were $4{\rightarrow}3{\rightarrow}3$ minutes for 3-stage press time and $45{\rightarrow}20{\rightarrow}5kg/cm^2$ for 3-stage press pressure. The rubber-based wood composite panel was very excellent in elasticity by combination of rubber chip in comparison with existing other wood-based materials. Therefore, it was considered that rubber-based wood composites can be applicable to every interior materials such as floor a room and will be expected to effective reuse and recycle of waste tires and wood-waste materials, and will be contribute to protection of environment pollution in earth.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2020.11a
• /
• pp.161-162
• /
• 2020

In this study, as part of securing related data, water droplets were dropped on the upper part of the wooden board for flooring in an environment such as floor heating, and the degree of absorption according to the surface temperature change was tested. The test results showed that the contact angle of the surface was low (25℃→40℃) or the droplet was absorbed into the small plate and disappeared. The contact angle of the OSB and MDF was decreased within 30 minutes, but the surface water droplet was maintained longer than the plywood. This is because the surface is coated with hydrophobicity unlike the plywood, but moisture absorption in the cross section after the second processing will not be prevented and it will lead to defect occurrence problem.

• Culinary science and hospitality research
• /
• v.15 no.4
• /
• pp.9-17
• /
• 2009

The microbiological examinations was conducted for the hygienic evaluation on ten Japanese restaurants during summer season in Gwangju, Korea. Total two hundreds swabbed samples using sponge were collected from the surface of facilities and utensils at restaurants. The number of total microorganism, coliform, E. coli, Staphylococcus, Salmonella, and Listeria were measured. The results demonstrated that most swabbed samples were contaminated with microorganisms and coliforms. The degree of contamination depended on the sample sites. The severely contaminated sites were floor, trench, and working table for the fish and total counts of those samples were over $10^4$ CFU/100 $cm^2$. The coliforms were detected on the floor, trench, and wood cutting board over $10^3$ CFU/100 $cm^2$. Moreover, coliforms was detected on the towel, dish, and working place for fish and vegetables. The E. coli was detected on the floor and trench of several restaurants. The Staphylococcus spp. was detected on the cutting board, towel, floor and trench of several restaurants. The Salmonella spp. and Listeria spp. were not detected all over the samples. From those results showed that sanitation management and disinfection were required on the Japanese restaurants.

• KIEAE Journal
• /
• v.10 no.3
• /
• pp.17-26
• /
• 2010

This study aims at exploring the characteristics of the Usonian houses of Frank Lloyd Wright from an ecological viewpoint. After considering the definition and application of ecological architecture through literature review, 28 Usonian houses were selected and analyzed for the study. Also, nine Usonian houses, which clearly have ecological and historical importance, were visited and more thoroughly analyzed. The result shows that Usonian houses are ecological in terms of 1) the relationship among nature, landscape and house, 2) the orientation, natural light and natural ventilation, 3) the use of natural local materials including wood, stones and bricks, 4) the use of floor heating (the On-dol system inKorea), 5) the human scale, 6) the use of the board and batten unit (an early system of prefabrication), and 7) the openness and flexibility of floor plans.

• Journal of the Korean Wood Science and Technology
• /
• v.36 no.1
• /
• pp.1-11
• /
• 2008

The purpose of this study is to examine the species of wooden members used in the Youngsanjeon Hall of the Sucknamsa temple in Anseong, Korea. Ninety-five wood samples from pillars, head-penetrating ties, beams, corner rafter, rafter, floor board and other wood members were identified. Seven species identified were hard pine, exotic pine, Zelkova serrata, Ginkgo biloba, Diospyros, Quercus(Cerrus) and Pyrus spp. In the case of pillars, eight were hard pines and the others Zelkova and Pyrus. Species of angle rafter were Ginkgo biloba and Zelkova. and those of beams were one hard pine and one Zelkova. Two purlin samples were Quercus(Cerrus) and rafters were hard pines except one Ginkgo and one exotic pine. Roof-filling timbers were identified as Zelkova and Diospyros spp. The other samples of roof-filling timbers were all identified as hard pines. The use of Ginkgo and several hardwoods in addition to hard pines may indicate supply of local logs near the Sucknamsa temple.

• Journal of the Korean Home Economics Association
• /
• v.38 no.11
• /
• pp.137-149
• /
• 2000

The Purpose of this study was to investigate actual condition about the modem adaptation of interior elements(floor, wall, ceiling, door & window) in traditional thatched roof house. The examined objects were interior space of 36 restaurants and cafes in Seoul and Kyung-Ki Do area. 1. Floor: Jang-pan was mostly alternated with linoleum which huts Jang-pan pattem. Wumul-maru was adapted from the original and Jang-maru was alternated with wood or linolium which has western state Jang-maru pattern. Mud was adapted from the original or alternated with slate stone or rough finish cement. 2. Wall: Rice proper was alternated with rice paper book witch has chinese character, paper for parcels or modem wall paper. Plaster-white paint or white handy coat. Mud-mud color paint or bamboo stick witch located in the mud wall orginal. Log-half cut log. Wooden board-without cross bar or irregular form. 3. Ceiling: Yondung-Chongang was mostly adapted from the original and Banja-Chonjang was alternated with rice paper book which has Chinese character or modem wall paper. 4. Door and Window: Ttisal-mun and Panjang-mun were adapted from the original. Wan and A’character door and window were simplified character itself.