• 한국전기전자재료학회논문지
• /
• 제16권3호
• /
• pp.253-262
• /
• 2003

In this paper, the interference cancellation system, which is used to cancel the feedback signal in the wireless communication system with the same frequency, is studied. The time varying feedback signal generated from transmitter antenna to receiver antenna reduces the performance of the receiver system. the interference cancellation system using adaptive feedback method(AF-ICS) is suggested to prevent the oscillation of the receiver system and maintain the maximum output power of the power amplifier by the reduction of time-varying feedback signal and also this paper conforms that the oscillation disappears from the output signal by cancellation of the feedback signal and the total output power is satisfied the system specification.

• 한국전자파학회논문지
• /
• 제30권3호
• /
• pp.195-201
• /
• 2019

위상배열 안테나는 개별 안테나의 위상을 제어함으로써 원하는 방향으로 빔 패턴을 형성할 수 있어 무선전력전송의 효율을 높이는데 효과적이다. 최적의 빔포밍을 통해 무선전력전송의 효율을 극대화하기 위해 송신기는 최적의 전송 경로를 인지해야 한다. 최적의 전파 경로 추정을 위해 일반적으로 송신기는 주기적으로 파일롯 신호를 전송하고 수신기는 이를 이용하여 최적의 경로에 해당되는 빔포밍 가중치를 계산하여 송신기로 피드백한다. 일반적으로 피드백 양이 안테나 수에 비례하여 증가하여 안테나 수가 많은 경우 피드백 오버헤드 문제가 대두된다. 본 논문에서 far-field approximation을 적용하여 피드백 양을 최소화하는 기법을 제안하고, 모의실험을 통해 간소화된 피드백 정보가 빔 패턴에 미치는 영향을 분석한다.

• 전자공학회논문지A
• /
• 제33A권11호
• /
• pp.19-31
• /
• 1996

Spread spectrum method gurantees good performance in digital communication system under multi-path interference and jamming signals. The purpose of this paper is to develop the wireless modem using DS/SS techinque. The transceiver consists of a spread spectrum DQPSK transmitter and a mtching receiver. The system operates with the chipping rate set to 4 Mcps and the number of chips/symbol at 64, making the data rate 62.5 Kbps using QPSK modilation. The receiver section uses a digital matched filter for fast acquisition of burst signals and uses the comparing the BER of proposed system iwth that of narrow bnd system under various additive white gaussian noises. It is showen that the proposed sysem has better performance than narrow band system. When jamming signals is added to the suggested DS/SS system, we also show that the experimental performance (BER) of the suggested wireless modem is almost same as theroretical performance.

• Journal of Communications and Networks
• /
• 제13권5호
• /
• pp.511-517
• /
• 2011

The capacity of wireless ad-hoc networks is analyzed for all kinds of information dissemination based on single and multiple packet reception schemes under the physical model. To represent the general information dissemination scheme, we use (n, m, k)-cast model [1] where n, m, and k (k ${\leq}$ m) are the number of nodes, destinations and closest destinations that actually receive packets from the source in each (n, m, k)-cast group, respectively. We first consider point-to-point communication, which implies single packet reception between transmitter-receiver pairs and compute the (n, m, k)-cast communications. Next, the achievable throughput capacity is computed when receiver nodes are endowed with multipacket reception (MPR) capability. We adopt maximum likelihood decoding (MLD) and successive interference cancellation as optimal and suboptimal decoding schemes for MPR. We also demonstrate that physical and protocol models for MPR render the same capacity when we utilize MLD for decoding.

• 한국전자파학회논문지
• /
• 제27권1호
• /
• pp.84-87
• /
• 2016

본 논문에서는 자기공명 방식의 무선전력전송 시스템용 100 W급 수신기를 설계, 제작하였다. 제안된 수신기는 1.8 MHz 대역, 100 W급 full-bridge 다이오드 정류기와 정전류 충전기로 구성되어 있다. 특히 정류기에는 30 V 이상의 과전압으로부터 수신기를 보호하는 과전압 보호회로와 수신기에 입력되는 여분 전력을 자동으로 소모하여 수신기의 임력임피던스를 부하변동에 관계없이 일정하게 유지시키는 능동 더미 부하가 내장되어 있다. 정전류 충전기는 최대 1 A의 충전 전류로 배터리를 충전할 수 있도록 설계, 제작되었으며, 충전전류를 제어할 수 있도록 구성되었다. 구성된 수신기를 이용하여 자기공명방식 무선충전 시스템을 구성하였다. 시스템은 130 W 송신기, 1.8 MHz 대역 송수신 공진기, 그리고 제안된 수신기로 구성되어 있으며, 자기공명방식으로 48 V 리튬-이온 배터리를 충전하도록 설계되었다. 시스템 측정 결과, 30 cm의 전송거리에서 약 54 %의 시스템 효율을 나타내었다.

• 전기학회논문지
• /
• 제59권11호
• /
• pp.2043-2047
• /
• 2010

This study is to solve problems of depletion of RF bandwidth frequency, confusion possibility, security that current wireless communications system have and is to confirm possibility of applying next generation network. To solve problems of current wireless communications system, visible light communications system for power line communications using ATmega16 Microcontroller is was realized and receiver property was analyzed. PLC exclusive chip APLC-485MA, Microcontroller ATmega16, 5pi bulb type LED and high flux LED, visible light receiving sensor LLS08-A1 were used for transmitter and receiver. Performance was analyzed by designed program and an oscilloscope. It was showed average 20% improved receiver rate rather than bulb type LED in the case of high flux LED through voltage change rate on communication distance and LED type of distance between 10 to 50 cm. The blue LED showed the best performance among measured LED types with above 10% of voltage decreasing rate. But As it gradually becomes more distant, the precise date was difficult to obtain due to weak light. To overcome these sort of problems, specific values such as changing conditions and efficiency value relevant to light emitting parts and visible light receiving sensor should be calculated and continuous study and improvements should also be accomplished for the better communications condition.

• ETRI Journal
• /
• 제43권2호
• /
• pp.197-208
• /
• 2021

Single-carrier frequency division multiple access (SC-FDMA) is currently being used in long-term evolution uplink communications owing to its low peak-to-average power ratio (PAPR). This study proposes a new transceiver design for an SC-FDMA system based on Walsh-Hadamard transform (WHT). The proposed WHT-based SC-FDMA system has low-PAPR and better bit-error rate (BER) performance compared with the conventional SC-FDMA system. The WHT-based SC-FDMA transmitter has the same complexity as that of discrete Fourier transform (DFT)-based transmitter, while the receiver's complexity is higher than that of the DFT-based receiver. The exponential companding technique is used to reduce its PAPR without degrading its BER. Moreover, the performances of different ordered WHT systems have been studied in additive white Gaussian noise and multipath fading environments. The proposed system has been verified experimentally by considering a real-time channel with the help of wireless open-access research platform hardware. The supremacy of the proposed transceiver is demonstrated based on simulated and experimental results.

• 재활복지공학회논문지
• /
• 제6권2호
• /
• pp.49-54
• /
• 2012

본 연구에서는 정신지체 아동들의 직업재활 훈련을 위한 e-러닝 시스템을 개발하였다. 개발된 시스템은 단계별 학습을 통하여 지식을 1차적으로 습득하고 문제 풀이와 시범 영상을 통하여 복습하도록 구성되어 있다. 또한, 리허설 기능을 통하여 습득된 정보가 올바르게 습득되었는지 점검할 수 있도록 구성하였다. 리허설을 위한 기기는 수신부와 송신부로 나누어 제작되었다. 송신부는 대상자의 작업을 감지하기 위한 적외선 센서와 압력센서 그리고 무선통신을 위한 블루투스 모듈로 구성하였다. 수신부는 무선통신을 위한 블루투스 모듈과 컴퓨터와의 통신을 위한 USB 입력 부분으로 제작되었다.

• Smart Structures and Systems
• /
• 제3권1호
• /
• pp.1-22
• /
• 2007

The energy efficiency of a self-powered wireless sensing system for pressure monitoring in injection molding is analyzed using Bond graph models. The sensing system, located within the mold cavity, consists of an energy converter, an energy modulator, and a ultrasonic signal transmitter. Pressure variation in the mold cavity is extracted by the energy converter and transmitted through the mold steel to a signal receiver located outside of the mold, in the form of ultrasound pulse trains. Through Bond graph models, the energy efficiency of the sensing system is characterized as a function of the configuration of a piezoceramic stack within the energy converter, the pulsing cycle of the energy modulator, and the thicknesses of the various layers that make up the ultrasonic signal transmitter. The obtained energy models are subsequently utilized to identify the minimum level of signal intensity required to ensure successful detection of the ultrasound pulse trains by the signal receiver. The Bond graph models established have shown to be useful in optimizing the design of the various constituent components within the sensing system to achieve high energy conversion efficiency under a compact size, which are critical to successful embedment within the mold structure.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 심포지엄 논문집 정보 및 제어부문
• /
• pp.51-53
• /
• 2006

This paper proposes a portable ECG monitoring system, which integrates uptodate PDA and RF communication technology. The aim of the study is to acquire the subject's biomedical signal without any constraint. It has two types of transmission mode, which are total signal transmission mode and HR(heart rate)/SC(step count) transmission mode. In audition, wireless communication technology uses Zigbee Wireless PAN and can work in low-power mode, which is one of the advantages of ZiBbee communication technology. The developed system is composed of a transmitter and a receiver. The transmitter has three-axial acceleration sensor. ECG amplifier and Zigbee communication controller. In total signal transmission mode, it can send data 50 packets per second whose transmission speed corresponds to 300 ECG samples and 60 acceleration samples. In HR/SG transmission mode, it can calculate heart rate from EEG data with 216 samples per second and step count from acceleration data and send a packet every cardiac cycle. The receiver forwards the received data to PDA, where the data can be stored and displayed. Therefore, the developed device enables to continuous monitoring for Activities of Daily Living(ADL). Also, this method will reduce medical costs in the aged society.