• Journal of Advanced Navigation Technology
• /
• v.13 no.6
• /
• pp.933-942
• /
• 2009

In this paper, the WAVE technology for IT based on Intelligent Transport System(ITS) which using by IEEE 802.11a PHY, IEEE 802.11p MAC(Medium Access Control) and IEEE P1609.3 was implemented. The WAVE system was designed that has maximum 0.5km communication range for RSU(Road Side Equipment) between vehicle, 12Mbps transfer speed when downlink at maximum 120km/h vehicle speed. To verify suitableness of the WAVE system for ITS, we measured several parameters on the real road: communication range when low and high speed, link establishment time, data transfer speed, PER (Percent Error Rate), and latency. From the experiment results, we demonstrated that WAVE is a suitable technology for IT based on ITS.

• Journal of Navigation and Port Research
• /
• v.29 no.1 s.97
• /
• pp.23-28
• /
• 2005

The signal in wireless multi-path channel is affected by fading and ISI because of high data rate transmission, so the signal has the high error rate. The present modulation and demodulation method of DSRC system can not expect sufficient for providing data service over 1 Mbps, so the channel equalization and advanced modulation and demodulation methods are required. OFDM is generally known as an effective technique for high data rate transmission system, since it can prevent ISI by inserting a guard interval. However, a guard interval longer than channel delay spread has to be used in each OFDM symbol period, thus resulting a considerable loss in the efficiency of channel utilization Therefore the equalizer is necessary to cancel ISI to accommodate advanced ITS service with higher bit rate and longer channel delay spread condition In this paper, the channel equalizer for the OFDM -DSRC system was designed and its performance in a multi-path fading environment was evaluated with computer simulation.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.6
• /
• pp.1091-1098
• /
• 2009

In this paper, we designed the authentication system for home network service and applied it to actual sensor nodes. The pair-wise pre-distribution key skim is applied for prevention of authentication key from sniffing on the wireless sensor networks. The authentication key and data are encrypted by using the CBC mode RC5 algorithm based on the SPINS. The experimental environment consists of a base station (BS)and sensor nodes and each sensor node sends both sensing data and the encrypted authentication key to the BS. For simulations we set up some what-if scenarios of security menaces in home network service.Slightly modified the TOS_Msg data arrays of TinyOS is suggested to store 8-byte authentication key which can enable data encryption and authentication at the each sensor node. As a result, malfunction caused by communication between BS and nodes of other groups of added nodes having malicious purpose can be protected. Also, we confirmed that a critical data of home networking service like vital signal can be transmitted securely through this system by encryption technique.

• Journal of Korea Society of Industrial Information Systems
• /
• v.23 no.4
• /
• pp.23-31
• /
• 2018

This paper presented the implementation and design of the 2T-2R wireless HD video streaming systems over 1.7 GHz frequency band using 3GPP LTE-TDD standard on NI USRP RIO SDR platform. The baseband of the system used USRP RIO that are stored in Xilinx Kintex-7 chip to implement LTE-TDD transceiver modem, the signal that are transmitted from USRP RIO up or down converts to 1.7 GHz by using self-designed 1.7 GHz RF transceiver modules and it is finally communicated HD video data through self-designed 2x9 sub array antennas. It is that communication method between USRP RIO and Host PC use PCI express x4 to minimize delay of data to transmit and receive. The implemented system show high error vector magnitude performance above 32 dBc and to transmit and receive HD video in experiment environment anywhere. The proposed hybrid beam forming system could be used not only in the future 5G mobile communication systems under 6 GHz frequency band but also in the systems over 6 GHz frequency band like ones in mmWave frequency bands.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.16 no.9
• /
• pp.2056-2063
• /
• 2012

In a port terminal, containers are stored and transshipped by yard tractors and crane vehicles. For operation efficiency of the terminal, location information of these vehicles is an essential factor. However, most of port terminals try to estimate location of these assets using indirect methods such as event tracking of shipping or unshipping containers. Because these kinds of events are rarely occurred, location of the event includes seriously locating error compared to a real location of vehicle. In this paper, we propose a real-time asset tracking system to obtain accurate and reliable location of terminal assets. The proposed system overcomes a location estimation error caused by container stacks which interrupt wireless communication. In order to mitigate uncertainty and increase accuracy of location estimation, we designed hardwares and multi-step locating system to resolve additional preblems. We implemented system components, and installed these at a port environment for evaluation. The result shows superiority of the system that the accuracy is approximately 5.87 meters (CEP).

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.25 no.1
• /
• pp.25-31
• /
• 2014

In this paper, a modified Alford loop antenna for on-body communication system is proposed. The proposed antenna operating in the ISM band is designed with consideration of human body effect. One of advantages of the Alford loop antenna structure is low-profile, however the Alford loop antenna is not suitable for on-body devices since it does not have a ground plane for other electronic part of on-body system and requires balanced feeding structure. To be embedded on on-body devices, the proposed antenna is design with the unbalanced feed structure and ground. The performance of the proposed antenna is simulated and measured when it is placed on the human body phantom to consider the effect of the human body. The proposed antenna a 10 dB return loss bandwidth over the ISM band and monopole-like radiation pattern with low-profile. The antenna has the surface of appropriate for on-body communication environment.

• Journal of the Korea Society of Computer and Information
• /
• v.12 no.3
• /
• pp.155-163
• /
• 2007

In this paper, Though sensors of Ubiquitous Middle-ware System based on RFID/USN can usually be reacted from six mouths to two years, they can be exhausted their power of storage battery only one day by communication rates and ranges. That is, the lifetime of sensor node is depended on how much spending power under wireless communication that can communicate its sensing data to its destination. Therefore, it is necessary that each sensor should be designed the Routing path to its destination, in order to remote collecting data. But, in order to improve lifetime of sensor node and modify inner setting, it is opposite to simple searching path method of sensor node by entering external commands. accordingly, 1:n sensor arrangement of n form command and data send-receive that is possible simulation do without interference other sensors and research to different sensor data analysis and conversion ways to convert Sensing data that accept from sensors to actuality information.

• Journal of Institute of Control, Robotics and Systems
• /
• v.14 no.3
• /
• pp.284-294
• /
• 2008

In this paper, we describe an implementation of small mobile robot that can be used at research and application of mobile sensor networking. This robot that will constitute the sensor network, as a platform of multi-robot system for each to be used as sensor node, has to satisfy restrictions in many aspects in order to perform sensing, communication protocol, and application algorithms. First, the platform must be designed with a robust structure and low power consumption since its maintenance after deployment is difficult. Second, it must have flexibility and modularity to be used effectively in any structure so that it can be used in various applications. Third, it must support the technique of wireless network for ubiquitous computing environment. At last, to let many nodes be scattered, it must be cost-effective and small. Considering the above restrictions of the mobile platform for sensor network, we designed and implemented robots control the current of actuator by using additional circuit for power efficiency. And we chose MSP430 as MCU, CC2420 as RF transceiver, and etc, that have the strength in the aspect of power. For flexibility and modularity, the platform has expansion ports. The results of experiments are described to show that this robot can act as sensor node by RF communication process with Zigbee standard protocol, execute the navigation process with simple obstacle avoidance and the moving action with RSSI(Received Signal Strength Indicator), operate at low-power, and be made with approx. $100.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.10 no.3
• /
• pp.43-50
• /
• 2010

DDC(Digital Down Converter) is a conversion technology to decimate to a lower sampling rate and DDC for the future development of communications technology has the necessary skills. So, it has been recognized in the wireless and the SDR(Software Defined Radio) system as essential components. In addition, research is underway on spectrum sensing for efficient communications environment due to the shortage of frequency resources. In this paper, the DDC systems were analyzed for CIC(Cascaded Integrator Comb) Filter, WDF(Wave Digital Filter), SRC(Sample Rate Conversion) each module. Moreover, we proposed a linkage effectively between DDC system and Spectrum Sensing for improve the efficiency of use of frequency by computer simulations. The simulation results of the DDC system was applied to the spectrum sensing capabilities. Also, performance and complexity of the results were derived and proposed system was the result of the check.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.8 no.6
• /
• pp.507-514
• /
• 2015

The Internet of Things era is approaching where all the things are equipped with smart sensors and communicate through internet. The three core technologies of the Internet of Things are 'detection technology' to get information from things and the environment, 'wired and wireless communications and network infrastructure skills' that support to connect things to the internet, and 'service interface technology' that processes the information appropriate to various services. Smart sensor application can expand to smartphone, smart cars, smart home systems, wearable electronic devices, telemedicine systems, and environmental monitoring systems, etc. In particular, technologies that mimic the five human senses. This study reviews the biological principles of the human senses and the principles of operation, research & development status, technology trends and market analysis of the sensors.