• 설비공학논문집
• /
• 제16권8호
• /
• pp.728-740
• /
• 2004

Heat sink has extended surface area for enhanced heat transfer. The enhanced convection heat transfer has been used widely, such as cooling electronic chips in the electronics industry. Heat sink usually requires an increase in the heat transfer and a decrease in the pressure drop, and must improve the performance in the flow field of industrial plants. In this study, wing fin heat sink was studied and tests were conducted in a rectangular cross sectional channel with wing fin heat sinks. The leading and trailing ends of a wing fin have a sharp edge, simulating the airfoil feature. Empirical correlations have been developed for wing fin heat sink types. And wing fin heat sinks have better cooling performance than elliptic fin and square fin types.

• International Journal of Air-Conditioning and Refrigeration
• /
• 제10권4호
• /
• pp.192-200
• /
• 2002

A modified asymmetric rectangular fin is analysed using the two-dimensional separation of variables method. This modified rectangular fin is made by attaching the wing on the top side of a rectangular fin. Heat loss from each side of this modified rectangular fin is calculated. The relative increasing ratio of heat loss between a modified rectangular fin and a rectangular fin is presented as a function of dimensionless fin volume, wing height and the location of the wing. Especially, to show the remarkable effect of the wing on the heat loss, the relative increasing ratios of heat loss between two different volume increasing methods are listed.

• Journal of the Korean Society for Industrial and Applied Mathematics
• /
• 제6권2호
• /
• pp.109-120
• /
• 2002

The dimensionless heat loss from a modified asymmetric rectangular fin is investigated as a function of the fin top and tip Biot numbers using the two-dimensional separation of variables method. A rectangular fin is modified by attaching the wing on the top side of the fin. Fin effectiveness and efficiency with the variation of the location of the wing and the width of the wing are presented. The relationship between top surface Biot number and bottom surface Biot number as well as the relationship between the dimensionless wing height and the location of the wing for equal amount of heat loss is also discussed.

• 설비공학논문집
• /
• 제16권8호
• /
• pp.683-690
• /
• 2004

A modified rectangular fin is analyzed by two-dimensional analytic method and finite difference method. Relative error of heat loss from the modified rectangular fin between analytic method and finite difference method is presented. Comparisons of fin effectiveness and heat loss between a modified rectangular fin and a plane rectangular fin are made as a function of the non-dimensional fin length and wing height for different positions of wings by using analytic method. The ratio of the incremental rate of heat loss to that of the area of a modified rectangular fin is shown as a function of the wing height. One of the results shows that performance of a modified fin is more improved as the wing approaches the fin root.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회B
• /
• pp.2023-2028
• /
• 2008

In present study, the flow field near the fin surface of plate fin - oval tube heat exchanger with delta wing vortex generator was numerically analyzed. As results, the well developed vortex behind delta wing was observed. These vortex can improve heat transfer fin surface behind delta wing vortex generators.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회B
• /
• pp.2390-2395
• /
• 2007

The present research was experimentally performed to analyze the effect of delta-wing vortex generators(DWVG) on the heat transfer of fin surface of the plate fin-oval tube. The local heat transfer coefficient of the fin surface for four kinds of DWVG's arrangement was measured by the naphthalene sublimation technique for Reynolds numbers ranging from 2000 to 3200. The results showed that the heat transfer of the plate fin-oval tube can be significantly enhanced by DWVG for relatively low Reynolds numbers.

• 청정기술
• /
• 제14권4호
• /
• pp.265-270
• /
• 2008

본 연구는 전자기기 모듈의 공기 냉각용 정렬 배열된 핀-휜 열교환기에서 휜 형상의 변화가 유동 및 열전달에 미치는 영향을 수치적으로 해석하였다. 휜 단면의 기하학적 형상은 세 가지로서 원형, 타원형, 그리고 날개형이었다. 취급된 모든 휜의 단면적과 높이는 서로 동일하지만, 그 표면적만은 서로 달랐다. 그 결과, 휜의 표면적, 열전달계수, 그리고 열전달 성능은 휜의 형상에 크게 의존하였다. 적절한 형상을 갖는 휜의 열전달 성능은 세 가지 형태의 핀-휜 중에서 날개형 핀-휜이 가장 우수하였다. 이러한 결과로부터 공기의 유량증가측은 휜의 밀도증가 없이 적절한 핀-휜의 형상변화만으로도 핀-휜 열교환기의 냉각성능을 크게 향상 시킬 수 있음을 알 수 있었다.

• 대한기계학회논문집B
• /
• 제33권10호
• /
• pp.757-766
• /
• 2009

In the present study, the effect of delta-wing vortex generators(DWVG) on the local heat transfer of the plate fin-oval tube was experimentally analyzed for Reynolds numbers for 2000, 2500 and 3200. The local heat transfer coefficient of the fin surface for four type DWVGs was measured by the naphthalene sublimation technique. As the results, the distribution of the heat transfer coefficient at rear of DWVGs showed longitudinal contours for common flow down DWVGs and wavy contours for common flow up DWVGs. The distribution showed many cell type contours at near wall and downstream for all DWVGs. Compared to case without DWVGs in present experimental tests, all DWVGs showed the best enhancement of heat transfer at Re=2000. Of 4 cases of DWVGs, D type showed the best enhancement of heat transfer.

• 한국자동차공학회논문집
• /
• 제9권3호
• /
• pp.84-91
• /
• 2001

Comparison between performance of a plate fin and that of a modified plate fin is investigated as a function of the position, the non-dimensional width and height of wings as well as the non-dimensional fin length using a two-dimensional separation of variables method. The ratio of the incremental rate of heat loss to that of the area of a modified plate fin is also presented as a function of the height of wings. The modified plate fin is made by attaching the wings to upper and lower sides of a plate fin. One of the results shows that performance of a modified plate fin is more improved as the wings approach left (higher) thermal reservoir.

• 전자공학회논문지
• /
• 제50권9호
• /
• pp.46-51
• /
• 2013

본 논문에는 무인항공기에 장착된 UHF 안테나의 최적 위치 및 형상이 다양한 위치에서 EM 시뮬레이션을 통하여 분석되어져 있다. EM 시뮬레이션을 위하여 FEKO를 이용하였다. 시뮬레이션의 복잡도를 줄이고 분석시간과 메모리 이용도를 최소화하기 위하여 비행체의 복합체 구조를 레이돔 구조를 제외하고 PEC 모델로 간략화 하였다. 시뮬레이션은 무인항공기의 날개와 Ventral Fin 위치에서 수행되어 졌고, 안테나 형상은 모노폴, 다이폴, 굴곡형 모노폴 안테나들을 이용하였다. 모노폴 안테나가 비행체 날개에 장착될 경우, 오른쪽 날개와 왼쪽 날개에 각각 장착되어지기 위하여 두 개의 안테나가 필요하고, 이 두 개의 안테나들은 가시선 데이터링크 지상 안테나에 대한 무인항공기 날개 방향에 따라 전환되어져야 한다. 모노폴 안테나가 Ventral Fin에 장착될 경우, 가시선 데이터링크 지상 안테나에 대한 무인항공기 날개 방향에 상관없이 하나의 안테나로 운용 가능하다. 또한, 안테나 이득도 비행체에 의한 Blockage 감소로 개선되어진다. 안테나 이득은 굴곡형 모노폴 안테나를 이용하여 더욱 더 개선되어 진다. 결론적으로 무인항공기에 장착된 UHF 안테나의 최적 위치 및 형상은 굴곡형 모노폴 안테나를 Ventral Fin 아래에 장착하는 것이다.