• Journal of Korean Society for Geospatial Information Science
• /
• v.21 no.4
• /
• pp.65-71
• /
• 2013

Wind shear means the variation of wind speed according to the height. Wind shear is the important factor affecting the energy production of wind turbines. Power Law is used to extrapolate wind speed data. Normally, a Power Law exponent of 0.143 is used and this is referred to as the 1/7th Power Law. The Power Law exponent is affected by atmospheric stability and surface roughness of the site. Thus, it is necessary to calculate the Power Law exponent of the site exactly for an accurate estimation of wind energy. In this study, wind resources were measured at the three Met-masts which were located in the coastal area of northeastern Jeju Island. The Power Law exponents of the sites were calculated and proposed using measured data. They were 0.141 at Handong, 0.138 at Pyeongdae, and 0.1254 at Udo. We compared annual energy productions which are calculated using a Power Law exponent of 0.143, the proposed value of the Power Law exponents for each site, and the measured data. As a result, the cases of calculating using the proposed values were more similar to the cases using the measured data than the cases using the 0.143 value. Finally, we found that the propsed values of the Power Law exponent are available to more accurately estimate wind resources.

• Journal of the Korean Solar Energy Society
• /
• v.36 no.1
• /
• pp.27-37
• /
• 2016

A simple but practical Ensemble Prediction System(EPS) for wind power forecasting was developed and evaluated using the measurement of the offshore meteorological tower, HeMOSU-1(Herald of Meteorological and Oceanographic Special Unite-1) installed at the Southwest Offshore in South Korea. The EPS developed by the Korea Institute of Energy Research is based on a simple ensemble mean of two Numerical Weather Prediction(NWP) models, WRF-NMM and WRF-ARW. In addition, the Kalman Filter is applied for real-time quality improvement of wind ensembles. All forecasts with EPS were analyzed in comparison with the HeMOSU-1 measurements at 97 m above sea level during Typhoon Bolaven episode in August 2012. The results indicate that EPS was in the best agreement with the in-situ measurement regarding (peak) wind speed and cut-out speed incidence. The RMSE of wind speed was 1.44 m/s while the incidence time lag of cut-out wind speed was 0 hour, which means that the EPS properly predicted a development and its movement. The duration of cut-out wind speed period by the EPS was also acceptable. This study is anticipated to provide a useful quantitative guide and information for a large-scale offshore wind farm operation in the decision making of wind turbine control especially during a typhoon episode.

• Proceedings of the KIEE Conference
• /
• 2000.07b
• /
• pp.846-848
• /
• 2000

In the early development of wind energy, the majority of wind turbines were operated at constant speed. Recently, the number of variable-speed wind turbines adopted pitch control apparatus has increased. This paper deal with a simulation of pitch control of variable-speed wind turbine and the response of pitch angle is traced in a given random wind speed.

• 한국전산유체공학회:학술대회논문집
• /
• 2011.05a
• /
• pp.236-239
• /
• 2011

This paper introduces the design concepts and characteristics of WinDS3000$^{TM}$(TC IIa) which is a trade name of Doosan's 3MW offshore/onshore wind turbine. WinDS3000$^{TM}$(TC IIa) has been designed in consideration of high Reliability, Availability, Maintainability and Serviceability (RAMS) and low cost of electricity (CDE) for the TC IIa condition based on GL guideline. An integrated drive-train design with an innovative three-stage gearbox has been introduced to minimize nacelle weight of the wind turbine and to enhance a high reliability for transmission. A permanent magnet generator with full converter system has been introduced to get higher efficiency in partial load operation and grid-friendly system for both 50 Hz and 60 Hz. A pitch-regulated variable speed control system has been introduced to control wind turbine power while generator reaction torque can be adjusted almost instantaneously by the associated power electronics. The wind turbine has been also equipped with condition monitoring and diagnostic systems in order to meet maintainability requirements.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.06a
• /
• pp.534-535
• /
• 2009

The objective of this research aims preliminary assessments of the proposed plans of offshore wind farm development based on the recently established national offshore wind map and suitability assessment system of offshore wind farm. Incheon Mueodo, Busan Dadaepo-Gadukdo, Sinangun Haeodo have been assessed considering geographic constraints such as water depth, offshore distance, national park, grid connection, and meteorological constraint such as wind power density and wind direction. According to the assessment, Mueodo plan has a weak point in grid connection and several geographic limitations are involved in Haeodo plan while Dadaepo-Gadukdo seems the most possible plan among the review cases. Because of limited assessment in this research, more detail and further consideration are necessary to make a decision of a feasibility project at proposed sites.

• 한국신재생에너지학회:학술대회논문집
• /
• 2006.11a
• /
• pp.286-289
• /
• 2006

To get the better efficiency in Korean type wind characteristics, a new wind turbine blade was developed with some structural, vibrational, and aero-elastic analysis for the design of the full-scale blade. A series of full domestic technology from design to manufacturing was created and used in the middle of the development of nelv wind blade. And it was equipped and measured at the wind test side in the Jeju island. After test, it is verified that the blade has the regular capacity of 10kW at the air velocity of 10m/s. And it shows better capacity in the low air-velocity compared to the imported blade. therefore it can be made by only domestic technology, and used for the domestic wind distribution with the better power generation.

• Journal of Wind Energy
• /
• v.10 no.4
• /
• pp.20-27
• /
• 2019

High-speed shaft coupling in a wind power system transmits power and absorbs variations in length and spindle dislocation between the gearbox and generator. Furthermore, the coupling has an insulation function that prevents electrical corrosion caused by the flow of the generator's current into the gearbox and prevents overload resulting from sudden power failure from being transferred to the gearbox. Its design, functions, and part verification are described in the IEC61400 and GL Guidelines, which specify that the part must have a durability life of 20 years or longer under distance variation and axial misalignment between the gearbox and the generator. This study presents the design of a high-speed coupling through composite stiffness calculation, structural analysis, and comparative analysis of test and theory to identify the characteristics of high-speed coupling for a large-capacity 6 MW wind power generator. A prototype was fabricated by optimizing the manufacturing process for each part based on the design, and the reliability of the fabricated prototype was verified by evaluating the performance of the target quantitative evaluation items.

• Superconductivity and Cryogenics
• /
• v.21 no.2
• /
• pp.2-6
• /
• 2019

• Proceedings of the KIEE Conference
• /
• 2001.10a
• /
• pp.349-353
• /
• 2001

Korea has a variety of favorable conditions for utilizing wind as energy. First of all, as a geographical characteristic, it is a peninsular country with its three frontiers surrounded by sea. Such a location makes the country influenced, all the year round, both by sea winds and by seasonal winds, so that it has a good possibility of putting its rich wind resources to use as an energy source. Particularly, in view of the results of observations and analysis of actual data about wind sources, it is quite possible to build wind paver plants in many regions across the country, such as inhabited islands dotted on its southern and western coasts around the Korean peninsular, a number of uninhabited islets attached the main islands, large-scaled reclaimed lands, and major inland areas. In Korea, the attempt to develop the technology of wind paver generation started in the 1970's. It was since 1988, when the Law on the promotion of Alternative Energy Development was enacted, that research and development activities for employing the wind force as a part of energy source have got into full swing. At that moment, however, due to the low level of domestic technological development, such efforts were mainly focused on the attainment of basic technologies with regard to wind power generation. Recently, there have been many noticeable changes in the international as well as domestic environments, such as the conclusion of the International Climate Treaty and the increase in public concerns of natural environment. It is quite possible to predict that the demand for wind paver generation will increase in the near future. Therefore, recognizing that wind, as a clean energy source, can be a promising method for coping with the International Climate Treaty and for replacing the fossil fuel, oil, this essay investigates the development history of wind paver generation systems and the status of technological development in Korea and presents an appropriate model for the development of the paver generation system that can compete with other energy sources.

• 유체기계공업학회:학술대회논문집
• /
• 2004.12a
• /
• pp.379-384
• /
• 2004

A prototype of 750 kW direct-drive wind turbine generator system, KBP-750D is under development in Korea. For the gearless, direct-drive prototype a synchronous generator with permanent magnets has been developed. The upwind 3-blade type machine employs variable speed and pitch control. The operating ranges of wind and rotor speed are 3 to 25 m/s and 9 to 25 rpm, respectively. The tip speed ratio of rotor blade is 7.5, designed for power coefficient 0.47, The blade pitch and torque are controlled with the predefined torque-speed curve according to the conditions of wind and public electric grid. This paper describes the outlines of primary components of KBP-750D.