• Proceedings of the KWS Conference
• /
• 2006.05a
• /
• pp.157-159
• /
• 2006

This study used by high speed DSP for more developing capability of inverter GMA welding machine. It also is designed by high speed DSP GMA welding system for real time control and improve of welding capability throught the switching frequency control by using of high speed DSP.

• Journal of Welding and Joining
• /
• v.31 no.1
• /
• pp.26-32
• /
• 2013

Recently, welding technology of nonferrous metals which were difficult to implement by arc welder has become available through digitalization of arc welding machine. Among them, the welding quality improvement of aluminum welding is very noticeable. These results increase the arc stability by controlling arc current and voltage waveform precisely, and control wire feed speed by synchronizing with arc current which the feed rate of filler wire is controlled by a precise motor control of servomotor and not by a simple constant speed feeding. Not only through the hardware digitalization of arc welding machine but also through advance of software of arc welding, it became possible to implement a certain level of welding quality by a simple operation. These led to CMT welding process implementation which requires low heat input than current arc welding and highly increased the applicability of the aluminum welding.

• Proceedings of the KSME Conference
• /
• 2001.06b
• /
• pp.319-324
• /
• 2001

This paper presents the motion control of a mobile robot with arc sensor for lattice type welding. Its dynamic equation and motion control method for welding speed and seam tracking are described. The motion control is realized in the view of keeping constant welding speed and precise target line even though the robot is driven along a straight line or corner. The mobile robot is modeled based on Lagrange equation under nonholonomic constraints and the model is represented in state space form. The motion control of the mobile robot is separated into three driving motions of straight locomotion, turning locomotion and torch slider controls. For the torch slider control, the proportional integral derivative (PID) control method is used. For the straight locomotion, a concept of decoupling method between input and output is adopted and for the turning locomotion, the turning speed is controlled according to the angular velocity value at each point of the comer with range of $90^{\circ}$ constrained to the welding speed. The experiment has been done to verify the effectiveness of the proposed controllers. These results are shown to fit well by the simulation results.

• Journal of Welding and Joining
• /
• v.24 no.1
• /
• pp.43-49
• /
• 2006

This paper describes the friction surface modification which has been successfully developed with the friction stir welding recently There are several problems including just position control and backlash in conventional friction surface modification system. Therefore it has been developed the friction surface modification system which has been controlled precisely both position and force by driving hydraulic cylinder in this paper. The mechtrode rotation speed(N) and feeding speed(Vz), travel speed(Vx,y) are of critical importance for the width and thickness of the coating in friction surfacing process. But there is no theoretical method of determining interrelations between process parameters affect the coating width and thickness. As a result of DOE(design of experiment) with developed system, the coating thickness and width seemed to decrease according to increase the mechtrode rotation speed(N) and traveling speed(Vx,y), to decrease feeding speed(Vz) apparently. However as the result of regression analysis the main effect was only the mechtrode rotation speed in the coating thickness.

• Journal of Welding and Joining
• /
• v.23 no.5
• /
• pp.14-19
• /
• 2005

In high speed $CO_2$ welding, it has been blown to produce no sound bead with undercut or humping bead. In this study welding phenomena through synchronized high speed camera and output welding voltage and current waveform has been analyzed. For the purpose to improve a welding bead, effect of short circuit current rise slope has been examined. With commercial power source it was produced no sound bead by instantaneous short circuit, long arc period and stubbing at welding speed 2.5mm/min Humping bead or undercut were showed by instantaneous short circuit and long arc period. Also, the weld bead was not formed during the long short circuit period after stubbing start and long arc extinguishment period after wire sticking by failure of arc regeneration, because the droplet was not transferred to weld pool. With increasing short circuit current rise slope the frequency of stubbing was decreased and the normal short circuit rate was increased. A control of short circuit current rise slope was effective factor in high speed welding.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.917-922
• /
• 2003

In this paper, a high speed rotating arc sensor for automatic fillet welding is introduced. In order to track the welding seam, The high speed rotating arc sensor is used. The welding tip of a high speed rotating arc sensor rotates about 3000 rpm using DC motor. The rotating torch is driven by gear between welding torch body and wire guide. The welding current is measured by using the current sensor and rot at ing position sensor. To realize the welding seam tracking algorithm with accuracy, a software filter algorithm using the moving average method is applied to the measured welding current in the microprocessor. The welding mobile robot with two wheels and two sliders is developed for fillet welding. The welding mobile robot can control its traveling direction and turn itself around the corner. The effectiveness is proven through the experimental results conducted with varied fillet tracking patterns.

• Journal of the Semiconductor & Display Technology
• /
• v.2 no.2
• /
• pp.21-24
• /
• 2003

Seam seal welding on the semiconductor package is a process for sealing the packages of semi-conductors, crystal parts, saw filters and oscillators with lid plate by seam welding. This paper presents the development process of automatic seam seal welding system. In this process, the process algorithm, high precision welding current control, design of welding head, high speed and high precision feeding mechanism and user interface process control program technologies are included.

• Journal of Power System Engineering
• /
• v.20 no.3
• /
• pp.51-56
• /
• 2016

In this study, the tensile tests and hardness tests were carried out for the joints characteristics in friction stir welds of Al 5052 alloy. Three way factorial design was applied to optimal welding conditions, whose control factors were shoulder diameter, rotation speed and welding speed of tool. From the results of this study, the optimum condition for maximum yield strength was predicted as the shoulder diameter of 15 mm, welding speed of 500mm/min and rotating speed of 1000 rpm. And the presumed optimal yield strength was estimated to be $167.36{\pm}7.82MPa$ with 99% reliability. In addition the increaser rotation speed of tool and the decreaser welding speed, the decreaser the hardness at welding part.

• Proceedings of the KWS Conference
• /
• 2002.05a
• /
• pp.68-70
• /
• 2002

A CCD camera with a laser strip was applied to realize the automation of welding process in GMAW. The Hough transformation was used to extract the laser stripe and to obtain specific weld points. In this study, a neural network based on the generalized delta rule algorithm was adapted for the process control of GMA, such as welding speed, arc voltage and wire feeding speed.

• Journal of Welding and Joining
• /
• v.16 no.1
• /
• pp.77-87
• /
• 1998

This paper deals with the effect of laser welding parameters on the weld formation. Thin steels for automotive application were prepared so as to be welded with high power carbon dioxide laser system. Major process parameters were position of focus and travel speed. The effect of shielding gas was also discussed by employing the high speed photometry. Test results showed that the optimal position of focus varied in accordance with the joint configuration; bead-on-plate, butt or lap welding. It was recommended that the position of focus for the lap welding be located at slightly inner part of the material to be welded. In this case, however, it was noticeable that the weld penetration ratio, d/t$_{0}$ dropped drastically at the critical region. Results also demonstrated that both the bead width and penetration reduced as the travel speed increased. The penetration ratio showed two distinct regions; stabilized zone at the lower range of the travel spped and sudden drop zone at the higher range of travel speed. Lower limit of the penetration for acceptable weld was proved to be about 90% of the parent metal thickness based on the physical properties of the weld. Mixed gas application for both the shielding of molten metal and laser induced plasma control was recommended as far as the penetration was concerned.d.