• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1994.10a
• /
• pp.492-498
• /
• 1994

The bicycle production process mainly consists of welding process of pipes and its quality is determined by geometrical symmetry of arrangement of welded pipes. Hence, manual quality control of bicycle frames was very inefficient and required much time in dimentional inspection and does not reserve high precision. In this paper we introduce a method of fast and accurate dimensional inspection of bicycle frame using the Stereo Vision system and related some image processing techniques.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.04b
• /
• pp.389-395
• /
• 1995

The bicycle production process mainly consists of welding process of pipes and its quality is determined by geometrical symmetry of arrangement of welded pipes. Hence, manual quality control of bicycle frames was very ineffecient and required much time in dimensional inspection and does not reserve high precision. In this paper we introduce a method of fast and accurate dimensional inspection of bicycle frame, using the Stereo Vision system and related some image processing techniques.

• Journal of Adhesion and Interface
• /
• v.7 no.4
• /
• pp.10-12
• /
• 2006

The successful use of adhesively bonded parts depends on the defect-free bond of the components. Therefore it is necessary to detect relevant faults and defects in an early state of the production. A 100% test should be pursued, but especially at complicated structures the detection of defects is not easy. Possible testing methods, which show a high potential for the NDT of adhesively bonded parts, are thermography based NDT methods. At present mainly two different procedures of active thermography are being used: Pulse and Lock-In Thermography. With pulse thermography the examined material is warmed up with a short energy pulse (light, eddy current or ultrasonic pulse) and the heat response is recorded after a certain time. The result is an infrared image which indicates material defects in different depths. This paper presents a variety of images showing the capability of Lock-In Thermography to image subsurface defects. Several examples of adhesives joints qualify the ultrasonic Lock-In-Thermography for the in-process quality control for adhesive bonded components.

• Journal of Ocean Engineering and Technology
• /
• v.5 no.1
• /
• pp.97-105
• /
• 1991

In this paper, the fatigue strength and the fatigue crack propagation behaviors of the round bar specimens which were spirally built up by welding and subsequently hardened by quenching were investigated. The material used was SF60 which was whdely employed in mechanical components, especially shafts. Fatigue tests were conducted at the fully reversed condition(R=-1) and axial and load control in the room temperature ahd air environment. The experimental results were expressed by both the range of stress intensity factor ($\Delta{K}$) and the effective range of stress intensity factor ($\Delta{K}_{eff}$). It was clarified that applying of quenching after the building up welding process improved the fatigue strength and the gatigue crack propagation property in the low range of $\Delta{K}$ of the built up round bar specimen.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.30 no.5 s.248
• /
• pp.602-608
• /
• 2006

Vehicle components such as lower control arm are usually affected by heat during the welding process. As a result, residual stress is generated, which has much effect on mechanical performances such as crashworthiness and durability. In this study, the residual stress in lower control arm has been measured by the x-ray diffraction method and been analyzed by finite element methods. Heat transfer during seam weld process has been calculated and used in calculating thermal deformation with temperature dependent material properties. High residual stress has been found at vertical wall both by measurement and simulation. The simulation also showed the residual stress re-distribution when the component is subjected to cyclic loading condition.

• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.757-762
• /
• 2002

Many reports have been shown that the buoyancy, electromagnetic force, surface tension, and gas shear stress are the driving forces of weld pool circulation in arc welding. Among them, the surface tension of molten metal plays an important role in the flow in weld pool, which are clarified by the specially designed experiments with small particles as well as the numerical simulations. The surface tension is also related to the penetration in arc welding. Therefore, a quantitative evaluation of surface tension is demanded for the development of materials and arc process control. However, there are few available data published on the surface tension of molten metals, since it depends on the temperature and the composition of materials. In this study, a new method was proposed for the evaluation of surface tension and its temperature dependence, in which it is evaluated by the equilibrium condition of acting forces under a given surface geometry, especially back surface. When this method was applied to the water pool and to the back surface of molten pool in the stationary gas tungsten arc welding of thin plate, following results were obtained. In the evaluation of surface tension of water, it was shown that the back surface geometry was very sensitive to the evaluation of surface tension and the evaluated value coincided with the surface tension of water. In the measurement of molten pool in the stationary gas tungsten arc welding, it was also shown that the comparison between the surface tension and temperature distribution across the back surface gave the temperature dependent surface tension. Applying this method to the mild steel and stainless steel plates, the surface tension with negative gradient for temperature is obtained. The evaluated values are well matched with ones in the published papers.

• Special Issue of the Society of Naval Architects of Korea
• /
• 2006.09a
• /
• pp.112-121
• /
• 2006

The vertical displacement of a ship on the basis of the sea level is an important parameter for its stability and control. To indicate the displacement on operating conditions, "draft marks" are carved on the hull of the ship in various ways. One of the methods is welding. The position, shape and size of the marks are specified on the shipbuilding rules by classification societies to be checked by shipbuilders. In most cases, high-skilled workers do the welding along the drawing for the marks and welding bead becomes the marks. But the inaccuracies due to human errors and high labor cost increase the needs for automating the work process of the draft marks. In the preceding work, an indoor robot was developed for automatic marking system on flat surfaces and the work proved that the robot welding was more effective and accurate than manual welding. However, many parts of the hull structure constructed at the outdoor are cowed shapes, which is beyond the capability of the robot developed for the indoor works on the flat surface. The marking on the curved steel surface requiring the 25m elevations is one of the main challenges to the conventional robots. In the present paper, the robot capable of climbing vertical curved steel surfaces and performing the welding at the marked position by effectively solving the problems mentioned earlier is presented.

• Journal of Welding and Joining
• /
• v.31 no.2
• /
• pp.26-29
• /
• 2013

The latest research & development trend on friction stir welding and friction stir processing technologies presented in the international symposium, 'Friction Stir Welding & Processing VII'. Papers and presentations about high temperature materials such as advanced high strength steel, stainless steel and titanum alloy shoot up this year. Papers on modeling of metal flow and control of process parameters also increased. The FSP technologies for manufacturing of carbon materials reinforced metal matrix composites were reported, too.

• Journal of Power System Engineering
• /
• v.21 no.1
• /
• pp.30-36
• /
• 2017

In robot industries, the request to obtain a high efficiency and accurately controlled electric actuator has been growing. Nevertheless, the effectiveness of electric actuators is significantly affected by the presence of factors such as nonlinearity, uncertain disturbance and unknown dynamics. Therefore, it makes difficult to derive an exact mathematical model of the controlled system. In this paper, a new method for easily recognizing and regenerating robot motions used in small size industries such as painting and welding parts is proposed. Instead of modeling the entire dynamic motion of the robot system, this method is based on the procedure of modeling and controller design for every arm individually. The proposed method does not require complex model and control system such that it gives easy working process to the small size industries. Based on this fact, in this research, the model and PID controller for every arm of the 3 DOF robot system are obtained separately. Some experimental results are implemented to validate the effectiveness of the proposed method.

• Steel and Composite Structures
• /
• v.44 no.2
• /
• pp.271-281
• /
• 2022

This study discusses challenges of running expandable profile liners (EPLs) to isolate trouble zones in directional section of a deep well, and summary the expandable profile liner technology (EPLT) field trial experience. Technically, the trial result reveals that it is feasible to apply the EPLT solving lost-circulation control problem and wellbore instability in the deep directional section. Propose schemes for optimizing the EPLT operation procedure to break through the existing bottleneck of EPLT in the deep directional section. Better-performing transition joints are developed to improve EPL string reliability in high borehole curvature section. High-performing and reliable expanders reduce the number of trips, offer excellent mechanical shaping efficiency, simplify the EPLT operation procedure. Application of the expansion and repair integrated tool could minimize the risk of insufficient expansion and increase the operational length of the EPL string. The new welding process and integrated automatic welding equipment improve the welding quality and EPL string structural integrity. These optimization schemes and recent new advancements in EPLT can bring significant economic benefits and promote the application of EPLT to meet future challenges.