• Proceedings of the Korean Society Of Semiconductor Equipment Technology
• /
• 2006.05a
• /
• pp.269-272
• /
• 2006

Surface contacts between mold and target should be in parallel for the imprinting mechanism. However, the size of contacting area makes it difficult for both mating surfaces to be in all contact because of precision level of the imprinting machine and the waviness of mold and target. The gripping force for both mold and target with the vacuum chuck is also major effect to interrupt the full contact, which must be avoided in imprinting mechanism. In this study, the preliminary study for the causes of non-uniformity of contacting surfaces such as mold and target is performed with $470{\times}370mm^2$ LCD panel size.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.142-144
• /
• 2009

We demonstrated narrow and good aspect-ratio inkjet-printed silver lines with multi-time over-printing methods. By using this strategy, narrow silver lines were obtained with 200 nm thickness and their width and gap between printed lines of uniform narrow silver lines were 30 ${\mu}m$ and 17 ${\mu}m$, respectively. It also had good conductivity, sheet resistacne of 0.36 ${\Omega}/{\square}$ and specific resistance of $8{\mu}{\Omega}{\cdot}cm$. In current stress test, narrow silver line with 30 ${\mu}m$ width was able to a current flow up to 50 mA (2.1A/$cm^2$). Using surface treatment on poly-arylate substrate with $UVO_3$, we obtained clean-edge narrow line without any edge waviness.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2004.04a
• /
• pp.87-90
• /
• 2004

In this paper, geometrically non-linear finite element analyses were performed to study the mechanical behavior of the material system of the envelope of stratospheric airships. The microstructure of the load­bearing plain weave layer was identified and modeled. The Updated Lagrangian formulation was employed to consider the geometric non-linearity as well as the induced structural non-linearity for the fiber tows. The stress-strain behavior was predicted and the effective elastic modulus was calculated by numerical experiments. It was found the non-linear stress-strain curves were largely different from those by linear analysis with much higher non-linear elastic moduli. The difference was more distinguishable when the tow waviness was smaller.

• International Journal of Air-Conditioning and Refrigeration
• /
• v.13 no.3
• /
• pp.158-166
• /
• 2005

The present study investigated experimentally and numerically the enhancement of absorption performance due to the waviness of falling film in the vertical absorber tube. The momentum, energy and mass diffusion equations were utilized to find out temperature and concentration profiles at both the interfaces of liquid solution and refrigerant vapor and the wall. Flow visualization was performed to find out the wetting characteristics of the falling film. The maximum heat transfer coefficient was obtained for the wavy flow using spring as an insert device through both numerical and experimental studies. Based on the numerical and experimental results, the maximum absorption rate was found for the wavy-flow using spring as the insert device. The differences between experimental and analytical results ranged from $5.0\;to\;25\%\;when\;Re_j>100$.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2002.04a
• /
• pp.395-400
• /
• 2002

Epoxy coating and sealing used in nuclear plants for the protection of radiation degrades with aging and hazardous atmosphere. In order to evaluate the degradation of the epoxy, dependence of the acoustic impedance on the change of mechanical properties has been used. Unlike metals, the surface of the epoxy coating on a concrete liner is so wavy that the acoustic impedance is difficult to measure by using the reflectivity of the ultrasound on the interface surface because of the irregular reflection and propagation from the epoxy surface. SA(simulated annealing) algorithm is applied to calculate the acoustic impedance using a reflection wave from the rough epoxy surface. The surface waviness and acoustic impedance are taken into account and determined by SA method to evaluate the state of degradation quantitatively.

• 유체기계공업학회:학술대회논문집
• /
• 2003.12a
• /
• pp.231-237
• /
• 2003

A numerical study has been conducted to investigate the effect of an inlet flow pulsation on mixing of two solutions with different concentrations in a micro conduit. We treat an unsteady, incompressible and two-dimensional flow through a micro conduit by adopting the momentum equations with the electrostatic force due to streaming current and the concentration equation. The feasibility of the inlet flow pulsation to enhance the mixing process inside the micro conduit is carefully examined by varying the inlet pulsation frequency. When a low-frequency pulsation is induced at the inlet, the interface between two solutions with different concentrations becomes wavy, which results in mixing enhancement. As the pulsation frequency increases, the waviness of the interface becomes meager, and the concentration gradients at the interface approach the value for the non-pulsating steady flow.

• Journal of the Korean Wood Science and Technology
• /
• v.25 no.4
• /
• pp.22-28
• /
• 1997

This research was carried out to obtain the fundamental data for the development of the technology and practical use of far-infrared radiation(IR) drying of quarter-sliced decorative veneers of walnut and red oak. The average drying rates of IR drying were about one and half to four times those of kiln drying and this tendency was prominent in thin veneer. The end wavinesses of the IR-dried veneers were smaller than those of kiln-dried veneers. These were largely recovered by the cold treatments after drying. The consumed electric power for IR drying was about one-fifth to two-fifthes compared to that for kiln drying.

• Journal of the Korean institute of surface engineering
• /
• v.34 no.4
• /
• pp.327-336
• /
• 2001

The skinpassing conditions such as roll type, roll force and roll roughness of the work roll were evaluated to give the surface properties of the galvanized steel sheets that were required for automotive and to get rid of the surface defects that caused with the bad control of galvanized coating process parameters. The surface defects of the galvanized steel sheets such as the ripple mark and the scratch were completely removed as the roll force of SPM work roll was increased and the amount of the transfer of roll surface texture to the strip was also gained a lot. The image clarity of electro discharge textured (EDT) coated steel sheets before and after painting was higher than that of the bright (BRT) and shot blasted (SBT) coated steel sheets because of higher PPI value, lower waviness and uniform surface pattern. Since micro-craters transferred on the surface of the galvanized steel sheets played a role of nucleation sites of chromate reaction, Increase of micro-craters was bring to better corrosion resistance with the increase of the roll force and the use of EDT roll at the skin pass mill.

• Journal of the Korean Society for Precision Engineering
• /
• v.31 no.11
• /
• pp.981-986
• /
• 2014

Printed electronics devices are made of several sets of printed patterns. The quality or printability of the printed patterns determines the electrical performance of such devices. Moreover, control of the printability determines the reliability of such devices. Despite its importance, few studies have been reported for the measurement of the printed patterns to evaluate their printability. In this study, a measurement method is proposed for printed patterns, including the definition of the properties to be measured, and the related software is described. The proposed method measures the width, pinholes, and edge waviness and evaluates the printability of the patterns quantitatively. The proposed measurement method could be an efficient tool to evaluate and enhance the printability of printed patterns in printed electronics.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.39 no.7
• /
• pp.653-657
• /
• 2015

A numerical investigation to simulate the selective growth of silicon-germanium quantum-dots via local surface diffusivity enhancement is presented. A nonlinear equation for the waviness evolution of film surface is derived to consider the effects of spatially-varying diffusivity, influenced by a surface temperature profile. Results show that the morphology of the initially planar film shapes into an undulated surface upon perturbation, and a steady-state solution describes a fully grown quantum-dot. The present study points toward a fabrication technique that can obtain selectivity for self-assembly.