• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.22 no.1
• /
• pp.81-88
• /
• 1997

Wavelength tunable, narrowbandwidth wvelength filters in compound semiconductor have been modeled, fabricated, and characterized. In order to obtain a narrow bandpass characteristics at 1.55.$\mu$m, a highly asymmertrical directional coupler structure composed of a strongly guided ridge waveguide and a weakly guided strip-loaded waveguide was used. The optimized filter structure modeling has been obtained by using the spectral index method, effective index method, and the coupled mode theory. Operation at a center wavelength a 1.537.mu.m with a bandwidth of 1.8nm and transfer efficiency of 50-70% is experimentally achieved. For the purpose of center wavelength tuning, the carrier injection in p-n diode structure has been theoretically investigated. It has been found that the tuning range of nanometer can be easily obtained by moderate amount carrier injection. We also found that the bandwidth becomes broad as the center wavelength tuning increases.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.23 no.5
• /
• pp.145-150
• /
• 2023

Non-uniform optical taper waveguides have been widely used as devices for high-efficiency mode coupling, as they are integrated with single-mode optical fibers or photonic crystal waveguides. In this paper, we present a new platform for chemical sensing and bio-sensing using optical taper waveguides with these characteristics. The principle of operation is based on the coupling efficiency and interference properties of optical directional coupler (DC) and multi-mode interference coupler (MMIC). First, the curvature characteristics of taper sections of DC and MMIC is explained, and the design specifications of optimized taper waveguide to increase waveguide sensitivity is selected. Next, the sensor response to the change in refractive index of sensing analyte is numerically analyzed. Numerical results show that as the length of couplers increases, the effective index per change in refractive index unit (RIU) of analyte increases, and that sensitivity can be tuned using taper DC and MMIC design techniques.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.42 no.7 s.337
• /
• pp.41-48
• /
• 2005

We design and fabricate 3-dB tandem directional coupler using the coplanar waveguide structure which is applicable to balanced amplifiers and mixers for 60 GHz wireless local area network system. The coupler comprises the multiple-sectional parallel-coupled lines to facilitate the fabrication process, and enable smaller device size and higher directivity than those of the conventional 3-dB coupler employing the edge-coupled line. In this study, we adopt the structure of two-sectional parallel-coupled lines of which each single-coupled line has a coupling coefficient of -8.34 dB and airbridge structure to monolithically materialize the uniplanar coupler structure instead of using the conventional multilayer or bonded structure. The airbridge structure also supports to minimize the parasitic components and maintain desirable device performance in V-band (50$\~$75 GHz). The measured results from the fabricated couplers show couplings of 3.S$\~$4 dB and phase differences of 87.5$^{\circ}{\pm}1^{\circ}$ in V-band range and show directivities higher than 30 dB at a frequency of 60 GHz.

• Korean Journal of Optics and Photonics
• /
• v.33 no.4
• /
• pp.137-145
• /
• 2022

A directional coupler device, one of the fundamental components of photonic integrated circuits, distributes optical power by evanescent field coupling between two adjacent optical waveguides. In this paper, the design process for manufacturing a directional coupler device is reviewed, and the accuracy of the design results, as seen from the characteristics of the actual fabricated device, is confirmed. When designing a directional coupler device through a two-dimensional (2D) beam-propagation-method (BPM) simulation, an optical structure is converted to a two-dimensional planar structure through the effective index method. After fabricating the directional coupler device array, the characteristics are measured. To supplement the 2D-BPM results that are different from the experimental results, a 3D-BPM simulation is performed. Although 3D-BPM simulation requires more computational resources, the simulation result is closer to the experimental results. Furthermore, the waveguide core refractive index used in 3D-BPM is adjusted to produce a simulation result consistent with the experimental results. The proposed design procedure enables accurate design of directional coupler devices, predicting the experimental results based on 3D-BPM.

• 정보저장시스템학회:학술대회논문집
• /
• 2005.10a
• /
• pp.153-153
• /
• 2005

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.63 no.2
• /
• pp.257-260
• /
• 2014

In this paper, a high gain waveguide array antenna combining horn antenna on slot radiator was designed. And the fabricated antenna showed enough gain, improved efficiency and broadband characteristics for receiving satellite signals, compare to conventional microstrip antenna which has dielectric loss and radiation loss on transmission line. For easy fabrication, the waveguide structure was composed by 3-stages of radiator, signal coupler and transmission line. By experiment, the array waveguide antenna of 4 by 16 showed 28.3[dBi] gain and 2:1 of VSWR. And by combining horn antenna structure, the gain was increased 1[dB]. The received signal from Koreasat 6 by measurement showed 16[dBc] of C/N on BS(Broadcasting Satellite)-band and 14[dBc] of C/N on CS(Communication Satellite)-band.

• ETRI Journal
• /
• v.25 no.2
• /
• pp.81-88
• /
• 2003

We designed a multimode interference (MMI) coupler to use in vertical coupling of double layered polymeric waveguides and analyzed the coupling characteristics by comparing our experimental and simulation results. We found that our proposed new structure, a stepped MMI coupler, is effective in vertical coupling between waveguide layers with a short length of MMI and has a high tolerance for the variation in the structure of an MMI coupler that can be induced as errors in the fabrication process.

• Korean Journal of Optics and Photonics
• /
• v.13 no.6
• /
• pp.461-466
• /
• 2002

Fiber-optic comb filters using a side-polished fiber coupler are proposed as multi-channel isolation filters on wavelength division multiplexing systems. We have demonstrated that the coupling efficiency between two waveguides is improved by the intermediate coupling layer in spite of the decrease of the optical power transfer between two waveguides due to the high-order modes of the overlay waveguide coupled with the side-polished single-mode fiber. When LiNbO$_3$with a 200-${\mu}{\textrm}{m}$-thickness was applied as a planar-overlay-waveguide, the comb filtering characteristics with a 4 nm-channel-spacing were achieved and the maximum power coupling occurred at the 1-${\mu}{\textrm}{m}$-thickness and the refractive index in range 1.52 to 1.53 of an intermediate coupling layer. If the intermediate coupling layer is optimized, an extinction ratio with more than 20 dB can be obtained. These experimental results are in good agreement with the BPM simulation.

• Korean Journal of Optics and Photonics
• /
• v.12 no.5
• /
• pp.406-413
• /
• 2001

We report theoretical and experimental results for the wavelength and polarization selectivity of a fiber-to-planar waveguide coupler made of a side polished single mode fiber covered with a planer waveguide incorporating a thin metal film. A simple but exact approach to obtain the modal properties of multilayer planar waveguide with a thin metal film is described. The device was modeled into equivalent 1 dimensional structure and its behaviour was analyzed based on coupled mode theory. The effects of metal film thickness and refractive index of superstrate on the device properties were measured and explained.

• Korean Journal of Optics and Photonics
• /
• v.15 no.4
• /
• pp.293-298
• /
• 2004

We investigate the effect of the wing width and thickness of a Double-Sided Deep-Ridge(DSDR) vertical directional coupler on the coupling length dependent on the polarization, We have found that the DSDR vertical directional coupler without a wing does not have polarization independent coupling lengths. The variation of the coupling length of TE and TM modes and the difference between the coupling lengths of the two modes are negligible as the wing width increases beyond the specific wing width for the same wing thickness. Thus, we can see that a DSDR vertical directional coupler has a wing width larger than the minimum wing width to obtain the polarization independent coupling length. The minimum wing width increases as the wing thickness increases for the same core thickness and as the core thickness decreases for the same wing width. Also, we have found that the minimum wing thickness is determined by the core thickness and the minimum wing thickness decreases as the core thickness increases.