• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.5 no.5
• /
• pp.994-1000
• /
• 2001

With the development of electromagnetic communication technology and increased use of electromagnetic wave, the countermeasure of EMI(Electromagnetic Interference) becomes more important socially, and interest for the electromagnetic wave absorber has also increased. In this paper, we have studied characteristics of frequency dependency on complex permittivity and complex permeability according to the changes of composition rate and sintering temperature of NiCuZn ferrite also known as electromagnetic wave absorber and further looked into effect of electromagnetic wave absorption properties. From the measurement where the composition of $Fe_2O_3$ and ZnO of NiCuZn ferrite was fixed at 49 and 34 mol% respectively while composition of NiO and CuO has been varied at each test, we found out that Initial permeability and permittivity were high and the absorbing ability of electromagnetic wave recorded best with $loss tangent(=\mur"/\mur')$ displays more than 1 within the frequency band of 2MHz~9.5MHz when the composition ratio of NiO was ranged around 8.5~9.5 mol% and the sintering temperature was $1080^{\circ}C$.TEX>.

• Composites Research
• /
• v.36 no.2
• /
• pp.92-100
• /
• 2023

In this paper, a machine learning and deep learning model for the design of circuit analog (CA) radar absorbing structure with a cross-dipole pattern on a glass fiber fabric reinforced plastic is presented. The proposed model can directly calculate reflection loss in the Ku-band (12-18 GHz) without three-dimensional electromagnetic numerical analysis based on the geometry of the Cross-Dipole pattern. For this purpose, the optimal learning model was derived by applying various machine learning and deep learning techniques, and the results calculated by the learning model were compared with the electromagnetic wave absorption characteristics obtained by 3D electromagnetic wave numerical analysis to evaluate the comparative advantages of each model. Most of the implemented models showed similar calculated results to the numerical results, but it was found that the Fully-Connected model could provide the most similar calculated results.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.26 no.4
• /
• pp.341-352
• /
• 1990

The purpose of this research is to develop the design/control method that can be used for the improvement of harbour tranquility and water quality of fishing ports. For this end, firstly, the hydraulic environmental characteristics of fishing ports in the coastal waters of the Korean Peninsula are analysed and discussed combined with disasters of facilities and vessels in the ports. Secondly the problems of water quality control is pointed out considered with the improvement measures of harbour tranquility such as the methods of lengthen of main breakwaters and construction of wave absorbing structures. Finally, the control characteristics of composite functions of water quality and tranquility of fishing port are discussed and the improved control method si proposed using the experimental results for the various measures. The proposed measure is proved to be a applicable method to improve these two main functions on the design of fishing port.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.32 no.6
• /
• pp.64-71
• /
• 2004

The object of this study is to design the Radar Absorbing Structures (RAS) having sandwich structures in the X-band ($8.2{\sim}12.4GHz$) frequencies. Glass fabric/epoxy composites containing conductive carbon blacks and carbon fabric/epoxy composites were used for the face sheets. Polyurethane(PU) foams containing multi-walled carbon nanotube (MWNT) were used for the core. Their permittivities in the X-band were measured using the transmission line technique. The reflection loss characteristics for multi-layered sandwich structures were calculated using the theory of transmission and reflection in a multi-layered medium. Three kinds of specimens were fabricated and their reflection losses in the X-band were measured using the free space technique. Experimental results were in good agreements with simulated ones in 10dB absorbing bandwidth.

• Polymer(Korea)
• /
• v.33 no.5
• /
• pp.420-428
• /
• 2009

In this study, the composites containing carbon black (CB) or carbon fibers were prepared, and the microwave absorbing properties and the absorption mechanism of them were investigated and discussed in the frequency range of 2-18 GHz, respectively. The optimum mass fraction of CB has been found as 6%, and the carbon fibers were discovered to absorb radar wave either under parallel or vertical polarization, the suitable gap distance between each bundle of which was 5 mm. According to the results of the single constitute absorber samples, the structured composites with the two kinds of absorbers combination were fabricated and studied at 2-18 GHz. The top layer absorbers affect the absorption performance a lot; the maximum reflection loss of composites with CB as top layer absorbers was -31.8 dB with the frequency range of 2.4 GHz below -10 dB, and the other type with CFs as the top layer absorbers obtained the reflection loss peak value of -31.4 dB with 2 GHz below-10 dB.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2000.10a
• /
• pp.153-156
• /
• 2000

The remarkable progress of electronics and radio communications technology has made our life abundant. On the other hand, the countermeasure of EMC becomes more important socially according to the increased use of electromagnetic waves. It had been required that the absorbing ability of an electromagnetic wave absorber is more than 20 dB, the bandwidth of which is required through 30 MHz to 1,000 MHz for satisfying the international standard about an anechoic chamber for EMI/EMS measurement. From November of 1998, however, the CISPR11 has accepted the extended frequency band from 30 MHz to 18 GHz in the bandwidth of EMI measurement. In this paper, we proposed the cutting com-shaped type satisfying the above requirments and carried out broadband design using the equivalent material constants method. Moreover, we have fabricated it and compared its characteristics with simulated one.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2000.05a
• /
• pp.386-391
• /
• 2000

Due to its characteristics of acoustic wave energy absorption, punched structures are generally applied on the wall of anechoic room. When the acoustic wave propagates through the punched plates, its energy dissipates into thermal energy by flow separation induced from the viscosity of acoustic media. The acoustic pressure difference between the for-side and the aft-side of punched plate ran be represented by the sum of drag term proportional to square of velocity and inertia term proportional to acceleration. The way to get the coefficients of the terms by an experiment or relatively simple calculation is introduced.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.4 no.4
• /
• pp.721-726
• /
• 2000

The remarkable progress of electronics and radio communications technology has made our life abundant. On the other hand, the countermeasure of EMC becomes more important socially according to the increased use of electromagnetic waves. It had been required that the absorbing ability of an electromagnetic wave absorber is mote than 20 dB, the bandwidth of which is required through 30 MHz to 1,000 MHB for satisfying the international standard about an anechoic chamber lot EMl/EMS measurement. From November of 1998, however, the CISPR11 has accepted the extended frequency band from 30 MHz to 18 GHz in the bandwidth of EMI measurement. In this paper, we proposed the cutting corn-shaped type satisfying the above requirements and carried out broadband design using the equivalent material constants method. Moreover, we have fabricated it and compared its characteristics with simulated one.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.2 no.4
• /
• pp.653-660
• /
• 1998

The purpose of this paper is to analyze the electromagnetic field characteristics of microstrip array antenna with the FDTD(finite difference-time domain method). Finite difference equations of Maxwell's equations are defined in rectangular coordinate systems. To simulate the unbounded problem like a free space, the Mur's absorbing boundary condition is also used. After modeling the microstrip array antenna with the grid structure, the transient response of the field distribution is depicted in the time domain.

• Journal of Ocean Engineering and Technology
• /
• v.25 no.6
• /
• pp.29-34
• /
• 2011

Various types of coastal structures have been constructed to prevent coastal disasters. Among these coastal structures, submerged breakwaters have been used more widely than all of the other coastal structures because of their excellent advantages in scenery effects, construction efficiency, and environmental benefits. This study investigated the potential of the horizontal plate submerged breakwater model. Usually, it is necessary for a submerged breakwater to minimize and compensate for the negative impacts on the marine environment and ecosystem caused by the marine construction. Thus, the prevention of coastal disasters was verified for this submerged breakwater model, regardless of its function as a fish reef. The purpose of this study was to investigate the hydraulic characteristics with changes in the crest width and porosity of a horizontal plate submerged breakwater and compare the results of this study with the results of other studies on permeable and impermeable submerged breakwaters.