• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2002년도 학술.기술논문발표회
• /
• pp.43-48
• /
• 2002

Since the basement building like the communication hole and etc. is built under the ground where it is pressed by the water, the leakage happens due to the dried-shrinking crack, the sinking crack, the creation of the work-joint of the building and etc. caused by the character of the material and construction way of the reinforced concrete building. Especially, a lot of repair for the leakage cannot help but being taken in temporary way without any noticeable countermeasure. Therefore, this kind of repair is socially criticized many times that this is defective construction even if this costs a lot. The fundamental reason of the above mentioned symptoms can be found in the creation of the work-joint caused by the character of the concrete building, the limitation of the physical performance of the existing water-proof and repair material, the limitation of the construction, the limitation of the physical sustaining performance of the concrete building, the limitation(heat-injury, deterioration) of the constancy of the durability caused by aging and etc. Therefore, in this study, we would like to present the better understanding on the water-proof seal relating to the application at the spot and its test evaluation related data since the necessity of the establishment of the quality control standard and the performance testing way on the relevant water-proof seal is rising a lot to regulate the water-proof technology and the leakage repair technology in accordance with the growth of the demand on the facility.

• 한국건축시공학회지
• /
• 제18권5호
• /
• pp.455-461
• /
• 2018

본 연구에서는 현재 국내에 일반적으로 적용되고 있는 폴리우레탄 도막방수재를 대상으로 12개월간의 장기 화학열화요인 작용 시 재료적 측면에서의 성능변화 특성을 인장성능 중심으로 평가하고, 도출된 데이터를 회귀분석기법을 적용하여 정량적 회귀식을 제시함에 따라 폴리우레탄 도막방수재의 장기내구성 확보여부에 대하여 대략적으로 성능예측 가능한 기초적 데이터 베이스를 구축하였다. 화학적 열화 환경에서 폴리우레탄 도막방수재는 약 23%~38%의 강도 저하를 나타냈다. 또한 신장률의 경우 약 15%~22%의 성능 저하를 나타내는 것을 확인할 수 있었으며, 제시한 회귀방정식은 화학적 열화조건에서 도막재의 성능 변화 정도를 예측하는데 활용 가능할 것으로 판단된다.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2019년도 춘계 학술논문 발표대회
• /
• pp.217-218
• /
• 2019

In this study, to overcome the limitation of material application as the surface layer of bridge decks (asphalt concrete, concrete), a newly developed waterproof sheet is proposed to be usable for both asphalt concrete and concrete. Subsequent tensile bond strength was tested, and the test results showed that the tensile bond strengths were similar to depending on the type of the surface layer material for bridge decks, confirming the applicability of the proposed material.

• 한국군사과학기술학회지
• /
• 제16권6호
• /
• pp.803-810
• /
• 2013

In this paper, we have verified the performance of ballistic resistance material on wet condition. Considering Korea terrain, soldiers may face many rivers and streams. However, bullet-proof jacket has no waterproofing and there's no water-proof standard in Military. Wearing wet bullet-proof jacket, soldiers can't be protected properly because of the decrement of jacket. Thus, we measure the performance of existing material on wet condition and analyze failure mechanism in order to indicate factors to improve bullet-proof jacket.

• 한국건축시공학회지
• /
• 제2권3호
• /
• pp.163-170
• /
• 2002

Recently, polishing tile(porcelain homogeneous polished tile) was used in the construction field as a finishing material. But, there happened some problems such as tile exfoliation by construction condition in early ages. Also, for use of polishing tile in the dry wall system which used to lightweight wall, the examination of adhesive stability of polishing tile is needed. In this study, adhesive strength of Polishing tile was investigated by tile bond types on gypsum board and non asbestos board coated by tar-urethane and Polymer modified cementitious waterproofing membrane(Series I). Then, the effect of heat stress and vibration was estimated on gypsum and non asbestos board(Series II). As the result of study are the follows; (1) Polishing tile(600$\times$400mm) construction on waterproofing layer : Both laboratory estimation and spot examination sieve were happened that fall of tile because their hardening speed is late. (2) To using powder style adhesives in the dry wail with waterproofing layer : Adhesive strength of tile is Influenced by interface bond area and base side condition. (3) Shock and heat stresses : obvious decline of adhesive strength is not happened

• Tribology and Lubricants
• /
• 제35권1호
• /
• pp.52-58
• /
• 2019

In the case of high-voltage connectors applied to automobiles, waterproofing has become an important issue for the safety of automobiles. In this study, structural analysis is performed on silicone rubber-type waterproof seals used in the voltage connector. For the structural analysis, the tensile properties of the actual rubber seal are evaluated using a miniaturized tensile testing machine. The Mooney-Rivlin material constants of the rubber seal are determined as follows; $D_1=0$, $C_{01}=0.241$, $C_{10}=0.0142$. The analysis shows that the contact pressure at the top of the seal where the seal and male connector are in contact is approximately three times higher than that at the bottom of the seal where the seal and female connector are in contact. It is confirmed that the waterproofing performance of the rubber seal depends on the contact pressure of the seal bottom where the seal and female connector are in contact. The contact pressure for waterproofing is found to be 4.7 bar. The strain concentration of the curved part is attributed to excessive initial tension. Therefore, a redesign is recommended for uniform stress or strain distribution in the curved section of the seal in response to the stress relaxation problem due to permanent deformation.

• 한국터널지하공간학회 논문집
• /
• 제20권6호
• /
• pp.1023-1037
• /
• 2018

최근 국내에서는 쉴드 TBM (Tunnel Boring Machine)을 이용한 터널 굴착에 대한 관심이 크게 증가하고 있다. 쉴드 TBM 터널은 비배수 터널로써 세그먼트 이음부에서 누수가 발생할 경우에는 터널의 사용성 및 안정성에 문제가 될 수 있다. 본 연구에서는 쉴드 TBM 터널의 세그먼트 시공 시 시공오차 및 세그먼트 과다변형에 의한 수팽창 지수재 및 가스켓 각각의 방수 성능을 검토하였다. 실험결과, 수팽창 지수재는 엇갈림에 대해서는 대응성이 좋으나, 틈새 간격에 대해서는 대응성이 불리한 것으로 나타났다. 반면에 가스켓은 틈새 간격에 대해서는 대응성이 좋으나, 엇갈림에 대해서는 대응성이 불리한 것으로 나타났다.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2017년도 춘계 학술논문 발표대회
• /
• pp.242-243
• /
• 2017

Despite its excellent properties, polyurea coating waterproofing material is exposed to sunlight when it is applied to the exterior wall of concrete by exposed waterproofing method such as a roof of a building, resulting in a problem of causing a large deterioration in performance compared to initial properties. The purpose of this study is to investigate the effect of carbon fiber incorporation on the performance of carbon fiber - reinforced polyureas and to study the optimum carbon fiber length and content respectively. Result of the study confirmed that the performance of the carbon fiber was improved by 2% or more, and the carbon fiber length was 30 ㎛ and the mixing ratio was 3%. It is expected that stable durability can be secured when manufacturing fiber-incorporated polyureas.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2022년도 가을 학술논문 발표대회
• /
• pp.145-146
• /
• 2022

The demand for a construction method capable of securing a safety environment and improving quality is increasing. There is a high risk of falling when working at a high place in an environment where it is difficult to secure visibility, such as an underground space, and there is a risk of falling if cement liquid waterproof materials are transferred to the top of the scaffold by manpower. In addition, when working on a high place in a poor environment, the quality uniformity of the upper part of the wall is deteriorated. In addition, as waterproof technicians gradually age and decrease, it is difficult to secure them, so it is urgent to prepare countermeasures against the shortage of waterproof technicians. Therefore, the purpose of this study is to develop cement liquid waterproof spouting construction equipment that can secure uniform quality of construction areas to prevent accidents and ensure safety of workers, improve work efficiency and quality due to improvement of work environment. The adhesion performance of the cement liquid waterproof material could be improved by about 20% in accordance with the use of the equipment.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2023년도 봄 학술논문 발표대회
• /
• pp.41-42
• /
• 2023

Test results for a total of four types of complex waterproofing methods were analyzed. In the case of the A method, the stress generated by high-viscosity compounds adhering to the base test body during the behavior of the test body was transferred to the sheet surface layer. In the case of the B method and the C method, the properties of the waterproof sheet consisting of a non-hardened seal based and a non-hardened seal are well reflected and stress absorption in the non-hardened seal layer acts strongly, rapidly reducing stress transfer to the surface of the waterproof sheet. In the case of the D method, slip occurs due to repeated behavior, and the stress on the attachment surface is reduced, and the stress transfer to the surface is greatly reduced. As a result, four types of composite waterproofing methods resulted in changing the stress transfer mechanism caused by behavior on the concrete surface due to the physical properties of the internal constituent material of the waterproof sheet.