• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.8
• /
• pp.2073-2080
• /
• 1994

In this paper, a model of material removal in abrasive water jet machining of brittle material is developed, and experimentally evaluated. Abrasive water jet machining proved to yield better material removal rate than other machining techniques for hard and brittle material (alumina ceramics). It was also found that large scale fracture may develop at the exit of the jet from the material. The fracture size was predicted as a function of water jet pressure and size of the hole. Finally, the feasibility of using acoustic emission signals for in-process monitoring of the abrasive water jet machining process is investigated.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.19 no.2
• /
• pp.213-218
• /
• 2013

This paper presents are experimental investigation to figure out slamming impact pressure and flow characteristics of a wedge type structure in free fall. The flow field has been obtained by 2-frame grey level cross correlation PIV(Particle Image Velocimetry) method, the impact presure of free fall structure by a pressure acquisition system apply to Dewetron system. The angles between a model and the free surface are adapted $15^{\circ}$, $25^{\circ}$, $35^{\circ}$ and $45^{\circ}$ respectively. Velocity field of water exit has higher better than water entry. The impact pressure under the bottom of the model ha been appeared higher values at 15 degrees than 45 degrees, and also at P1.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.18 no.4
• /
• pp.371-377
• /
• 2012

This paper presents an experimental investigation to figure out slamming impact pressure and flow characteristics of a rectangular Marine structure($800{\times}250{\times}50mm^3$) in free fall. The flow field has been obtained by 2-frame grey level cross correlation PIV(Particle Image Velocimetry) method, the impact pressure of the free fall model by a pressure acquisition system(Dewatron). The angles between a model and the free surface are adapted $10^{\circ}$ and $20^{\circ}$ respectively. Velocity field of water exit has higher better than water entry. The highest point, P2 of impact pressure under the bottom of the model has been appeared about 6 % higher values at 20 degrees than 10 degrees.

• Journal of Advanced Marine Engineering and Technology
• /
• v.37 no.5
• /
• pp.493-499
• /
• 2013

This paper presents are experimental investigation to figure out impact pressure and flow characteristics of a wedge type structure in free fall. The flow field has been obtained by 2-frame grey level cross correlation PIV(Particle Image Velocimetry) method, the impact pressure of free fall structure by a pressure acquisition system apply to Dewetron system. The angles between a model and the free surface are adapted $15^{\circ}$, $25^{\circ}$, $35^{\circ}$ and $45^{\circ}$ respectively. Velocity field of water exit has higher better than water entry. The impact pressure under the bottom of the model has been appeared higher values at $15^{\circ}$ than $45^{\circ}$, and also at P1.

• Korean Chemical Engineering Research
• /
• v.55 no.2
• /
• pp.201-213
• /
• 2017

Water is removed from crude oil containing water by using oil separator. This study aims to develop a three-dimensional (3D) Eulerian computational fluid dynamics (CFD) model to predict the separation efficiency of air-water-oil separator. In the incompressible, isothermal and unsteady-state CFD model, air is defined as continuous phase, and water and oil are given as dispersed phase. The momentum equation includes the drag force, lift force and resistance force of porous media. The standard k-${\varepsilon}$ model is used for turbulence flow. The exit pressures of water and oil play an important role in determining the liquid level of the oil separator. The exit pressures were identified to be 6.3 kPa and 5.1 kPa for water and oil, respectively, to keep a liquid level of 25 cm at a normal operating condition. The time evolution of volume fractions of air, water and oil was investigated. The settling velocities of water and oil along the longitudinal separator distance were analyzed, when the oil separator reached a steady-state. The oil separation efficiency obtained from the CFD model was 99.85%, which agreed well with experimental data. The relatively simple CFD model can be used for the modification of oil separator structure and finding optimal operating conditions.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.24 no.4
• /
• pp.485-494
• /
• 2000

The purpose of this paper is to investigate a critical heat flux(CHF) during forced convective subcooled and saturated boiling in free water jet system impinged on a rectangular heated surface. The surface is supplied with subcooled or saturated water through a rectangular jet. Experimental parameters studied are a width of heated surface, a height of supplementary water and a degree of subcooling. Incipient boiling point is observed in the temperature of 6${\~}8^{\circ}C$ of superheat of test specimen. CHF depends on jet velocity for various boiling-involved coolant system. CHF also is proportional to the nozzle exit velocity to the power of n, where n is 0.55 and 0.8 for subcooled and saturated boiling, respectively. CHF is enhanced with a higher jet velocity, higher degree of subcooling and smaller width of a heated surface.

• Ocean Systems Engineering
• /
• v.8 no.2
• /
• pp.223-246
• /
• 2018

In this paper the results of CFD simulations, that were carried out to study the impact pressures acting on a symmetric wedge during water entry under the influence of gravity, are presented. The simulations were done using a solver implementing finite volume discretization and using the VOF scheme to keep track of the free surface during water entry. The parameters such as pressure on impact, displacement, velocity, acceleration and net hydrodynamic forces, etc., which govern the water entry process are monitored during the initial stage of water entry. In addition, the results of the complete water entry process of wedges covering the initial stage where the impact pressure reaches its maximum as well as the late stage that covers the rebound process of the buoyant wedge are presented. The study was conducted for a few touchdown velocities to understand its influence on the water entry phenomenon. The simulation results are compared with the experimental measurements available in the literature with good accuracy. The various computational parameters (e.g., mesh size, time step, solver, etc.) that are necessary for accurate prediction of impact pressures, as well as the entry-exit trajectory, are discussed.

• The KSFM Journal of Fluid Machinery
• /
• v.16 no.4
• /
• pp.5-9
• /
• 2013

An experimental investigation has been carried out in order to evaluate characteristics of wetted-type multi-path ultrasonic flowmeters. The multi-path ultrasonic flowmeters were installed at various entrance and exit locations for several cases of pipe fitting(straight, $90^{\circ}$ double elbow) and valve(gate valve, butterfly valve). We measured the flow-rate at each location. The measurement data of test flowmeter were compared with the measured data of reference flowmeter. The uncertainties of reference flowmeter and test flowmeter are 0.3 %, 0.4 %, respectively. The results demonstrate the effects of flowmeter location as well as the measurement errors in flow rate. The distance between the flow disturbance factor and a flowmeter was an important element of the test.

• Journal of the Korean Society of Industry Convergence
• /
• v.22 no.2
• /
• pp.173-181
• /
• 2019

This study was carried out numerically to investigate the flow characteristics in the Venturi tube with $90^{\circ}$ T-branch tube and the inflow of condensed water into the Venturi tube from the branch tube. In this study, the diameter of the branch tube(1, 2, 3mm) and the neck diameter of the Venturi tube(0.3, 0.9, 1.5mm) were varied. The flow rate of the water at the Venturi tube inlet is 80cc/min and the water temperature is 288K. The condensed water temperature at the branch tube inlet is 355K. It was found that the velocity and pressure of the fluid near the branch point in the Venturi tube were more dependent on the diameter of the Venturi tube than the diameter of the branch tube. The temperature of the mixed water at the exit of the Venturi tube was the highest when the Venturi tube's neck diameter is 0.9mm and the branch tube diameter is 2mm. This means that the condensed water is flowing well through the branch tube.

• Fire Science and Engineering
• /
• v.32 no.5
• /
• pp.57-66
• /
• 2018

A sports center fire in Jecheon that caused 29 deaths and 40 injuries was analyzed based on initial response and management in order to investigate the causes of the casualties. The aspects of initial response included delay of reporting 119, not being guided to the exit for the body scrubber on the $2^{nd}$ floor for escape, opening the fire doors of the exits on the $1^{st}$ floor and $3^{rd}$ floor, not closing the fire door of the main stairs on the $3^{rd}$ floor, and not doing an emergency broadcast. The management aspects included closing the alarm valve of the sprinkler system on the $1^{st}$ floor, starting-stop of the fire pump controller, neglecting leakage of water and electricity between the false ceiling and ceiling in the parking lot, hiding the exit light in the ladies bathroom lounge on the $2^{nd}$ floor and piling up things in the exit, neglecting the button of an automatic door on the $2^{nd}$ floor, conventional fire safety management, insufficient inspection of fire equipment, and not working fire shutters and smoke exhaust windows.