• 한국환경교육학회지:환경교육
• /
• 제20권4호
• /
• pp.65-83
• /
• 2007

The purpose of this study was to survey science teachers, perception and attitudes on disposal of school laboratory waste water and materials. To fulfill this aim, a questionnaire was administered to 244 secondary school science teachers. The result of this study revealed that there was no large disparity in the degree of understanding of laboratory waste disposal and the laboratory waste water treatment, and in secondary science teachers' perception and practicing attitude on the environment. While science teachers had deep understanding of laboratory waste disposal and its influence on environmental pollution, they expressed less positive attitude toward the actual disposal of waste materials and waste water, and participation in teacher training. Therefore, it is necessary to provide standards of systematized disposal methods and proper disposal facilities in middle and high school laboratories, as well as to investigate teachers' needs before providing teacher training program.

• Journal of Electrochemical Science and Technology
• /
• 제9권2호
• /
• pp.157-162
• /
• 2018

In the study, herbaceous biomass waste including giant miscanthus, corn stalk, and wheat stalk were used to prepare commercially valuable activated carbons by KOH activation. The waste biomass predominantly consists of cellulose/hemicellulose and lignin, in which decomposition after carbonization and activation contributed to commercially valuable specific surface areas (>$2000m^2/g$) and specific capacitances (>120 F/g) that exceeded those of commercial activated carbon. The significant electrochemical performance of the herbaceous biomass-derived activated carbons indicated the feasibility of utilizing waste biomass to fabricate energy storage materials. Furthermore, with respect to both economic and environmental perspectives, it is advantageous to obtain activated carbon from herbaceous biomass waste given the ease of handling biomass and the low production cost of activated carbon.

• 한국재난정보학회 논문집
• /
• 제4권1호
• /
• pp.86-100
• /
• 2008

It is needed to classify the kinds of construction and demolition(c&d) debris to 6 catagories of waste concrete, waste asphalt concrete, waste wood, scraps, combustible waste and incombustible waste in order to properly do a separate discharge and to estimate unit generation rate in construction site. Also, in this case, the unit treating cost for mixed wastes should be applied with the unit treating cost for combustible waste. The construction standard materials estimation data is used for basic data for estimating unit generation rate. The mixed wastes in this data should be classified to waste wood, combustible waste and incombustible waste, and their ratio is obtained by using the unit generation rate of Asia Pacific Environment and Management Institute and Seoul Metropolitan Development Institute. The waste amounts generated from newly-built construction can be obtained from multiplying the loss rate by the amount of materials used from construction standard estimation data. Also, those from dismantling construction can be obtained by subtracting waste amount generated during newly-built construction from total input amount of materials in newly-built construction. Those in two cases can be used in construction site. It can be used for estimating the amount generated and establishing the treating plan in the case of setting up the policy of waste management and doing the environment impact assessment.

• Advances in concrete construction
• /
• 제10권5호
• /
• pp.417-429
• /
• 2020

Waste glass is a global solid waste with huge reserves. The discarded waste glass has caused a series of problems such as resource waste and environmental pollution, so it is urgent to recycle waste glass with high replacement level. Glass powder (GP), as a supplementary cementitious material (SCM), used in cement-based materials has already become one of the important ways to recycle waste glass mainly attributed to its pozzolanic reaction and filling effect, especially to the suppressed ASR expansion. This paper demonstrates an overview of the properties of GP and its effect on the fresh and mechanical properties of cement-based materials. The study found that the influence of GP on the performance of cement-based materials mainly depends on its content, particle size, color and type, curing conditions, and other SCMs. Finally, based on the problems involved in the investigation of concrete containing GP, some corresponding suggestions and efforts are given to further guide the utilization of GP in cement-based materials.

• 한국환경보건학회지
• /
• 제37권2호
• /
• pp.150-158
• /
• 2011

This research was conducted to estimate the physicochemical characteristics of waste catalyst and its in-process product from recycling and to suggest fundamental data for religious systems such as quality standards. Mo and V contents were increased from the waste catalyst to calcinated material and oxidized material. In the results of a heavy metals leaching test, Pb was not detected in any catalyst, calcinated and oxidized materials. Cu was not detected in the catalyst. However, it was detected in ${\leq}$1.16 mg/l for calcinated material and in 1.34~13.73 mg/l for $MoO_3$ oxidezed material. Concentrations in recycling in-process products (calcinated and oxidized materials) were higher than those of waste catalyst. Oil content of catalyst waste ranged from 0.01-14.03 wt%. Oil contents of calcinated and oxidized materials were greatly decreased compared to the catalyst waste. Carbon and sulfur contents as chemical poisoning material of catalyst waste ranged from 0.33-76.08 wt% and 5.00-22.00 wt%, respectively. The carbon contents of calcinated and oxidized materials showed below 20 wt%. The sulfur content showed below 8wt% for calcinated material and below 0.22 wt% for oxidized material.

• Journal of the Korean Wood Science and Technology
• /
• 제25권4호
• /
• pp.29-38
• /
• 1997

The effect and control of wood property of reconstituted composite panels for improved board properties by wood-waste materials and development of combination method for heterogeneous materials have been of interest to the wood science researchers. The purpose of this study is to consider the properties in relation to hot pressing conditions and to develope the optimum hot pressing condition with waste wood and waste tire for the manufacturing of composite boards. The study of composite boards for recycling of wood and waste tire is nothing up to the present. Physical and mechanical properties such as specific gravity, moisture content, swelling coefficient, modulus of rupture and modulus of elasticity in bending test were studied. The condition of 3-stage press time for the lowest moisture content of composite board was $4{\rightarrow}3{\rightarrow}3$ minutes. Specific gravity of composite panels was affected mainly by the amount of rubber chip. Because of the low rigidity and high elasticity in rubber chip, it is considered the composite panel was adequate material in the place of compression load, but not bending load. Therefore, it was concluded that a use of rubber-based wood composite panel is proper to the interior materials such as floor a room than exterior materials. From the test results, the most optimum hot pressing conditions were $4{\rightarrow}3{\rightarrow}3$ minutes for 3-stage press time and $45{\rightarrow}20{\rightarrow}5kg/cm^2$ for 3-stage press pressure. The rubber-based wood composite panel was very excellent in elasticity by combination of rubber chip in comparison with existing other wood-based materials. Therefore, it was considered that rubber-based wood composites can be applicable to every interior materials such as floor a room and will be expected to effective reuse and recycle of waste tires and wood-waste materials, and will be contribute to protection of environment pollution in earth.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 춘계 학술발표회 논문집(II)
• /
• pp.341-344
• /
• 2006

The waste glasses among plenty of wastes put out lately is limited in recycling and reusing, and the phenomenon hasn't been improved quite much. And besides, the recycling rate shows the 70.1%, relatively low. These waste glasses is currently used for road pavement materials, interior and exterior decorating materials in architecture, road painting meterials, auxiliary lagging materials for heat-retaining, coldness-retaining and soundproofing, and glass bottles. 30% of waste glasses powder is, however, not reused pratically. Therefore, in this research, we operated some tests including flow of mortar mixed with waste glasses powder, setting time, rheology and compressive strength to utilize waste glasses powder put out in the precess of recycling for admixture for repair mortar. As a result, we've found out that we can utilize waste glasses powder for admixture for repair mortar.

• 한국재료학회지
• /
• 제29권10호
• /
• pp.603-608
• /
• 2019

Plastic waste is becoming a problem in various countries because of the difficulty of natural decomposition. One type is PET plastic(Polyethylene Terephthalate), which is often used as a bottle for soft drink packaging, and LDPE(Low Density Polyethylene), which is also widely used as a food or beverage packaging material. The use of these two types of plastic continuously, without good recycling, will have a negative impact on the environment. Building material waste is also becoming a serious environmental problem. This study aims to provide a solution to the problem of the above plastic waste and building material waste by making them into a mixture to be used as bricks. Research is carried out by mixing both materials, namely plastic heated at a temperature of $180-220^{\circ}C$ and building material waste that had been crushed and sized to 30-40 mesh with homogeneous stirring. The ratios of PET and LDPE plastic to building material waste are 9 : 1, 8 : 2, 7 : 3, 6 : 4 and 5 : 5. After heating and printing, density, water absorption and compressive strength tests are carried out. Addition of PET and LDPE plastic can increase compressive strength, and reduce water absorption, porosity and density. A maximum compressive strength of 10.5 MPa is obtained at the ratio of 6 : 4.

• Advances in materials Research
• /
• 제11권4호
• /
• pp.251-277
• /
• 2022

Disposal of industrial waste in cities where municipal authorities permitting higher floor area ratio coupled with increasing living standards, a lot of demolition waste is being generated. Its disposal is a challenge particularly in megacities where no landfills are available. The ever-increasing cost of building construction materials also necessitates consuming demolition wastes in a useful manner to save fresh natural raw materials. In the present work, the crushed waste glass is used in high-strength concrete as a partial replacement of fine aggregate. The control concrete of grade M60 was proportioned following BIS 10262-2009. The crushed waste glass has been used as a partial replacement with varying percentages of 10, 20, 30, and 40% by weight of fine aggregate. Experimental tests were carried on the fresh and hardened state of the concrete. The effect of crushed waste glass on the workability of the concrete has been investigated. Non-destructive tests, acid attack tests, compressive strength, split tensile strength, and X-ray diffraction analysis was carried out for the control concrete and concrete containing crushed waste glass after 7, 28, and 270 days of normal curing. The results show that for the same w/c ratio, the workability of concrete increases with increasing replaced crushed waste glass content. However, the decrease in compressive strength of the concrete after 28 days of normal curing and further after 28 days of acid attacks, up to 30% replacement level of fine aggregate by the crushed waste glass is insignificant.

• 한국방사성폐기물학회:학술대회논문집
• /
• 한국방사성폐기물학회 2017년도 춘계학술논문요약집
• /
• pp.368-368
• /
• 2017