• Clean Technology
• /
• v.18 no.4
• /
• pp.360-365
• /
• 2012

With rapid increase in municipal solid waste (MSW) due to the rising economy, solid waste gasification emerges as one of the promising technologies. Separation of the carbon monoxide (CO) and hydrogen ($H_2$) from syngas obtained by gasification of MSW was studied using the polyamide composite membrane. The separation characteristics of the CO and $H_2$ were studied at different gas flow rates and stage cuts. The permeability of CO and $H_2$ along with the selectivity of $H_2$ with respect to CO was obtained. Furthermore, the Arrhenius plots were obtained to estimate the activation energies of CO and $H_2$ permeabilites.

• Journal of Climate Change Research
• /
• v.8 no.3
• /
• pp.231-237
• /
• 2017

In this study, the $N_2O$ emission factor of the facility was developed by measuring the kiln type pyrolysis melting facility. This used PAS (Photoacoustic Spectroscopy) method and measured the $N_2O$ emission concentration. From March 2016 to April 2016, it was measured over a total of two times and $N_2O$ concentrations were measured continuously for 24 hours using a 24 hour continuous measuring instrument (LSE-4405). The measured $N_2O$ emission concentration of the pyrolysis melting facility was 0.263 ppm on average and the emission concentration distribution in the range of 0.013~0.733 ppm was obtained. Therefore, the $N_2O$ emission factor of the kiln-type pyrolysis melting facility was estimated to be $0.829gN_2O/ton$-Waste. As a result of comparing the $N_2O$ emission factor of the thermal kiln type pyrolysis melting facility and the previous study, previous studies were about 18 times higher. It is estimated that this is due to the difference of furnace temperature, oxygen concentration and denitrification facilities. It is considered that the study of the emission factor of pyrolysis melting facility is an important factor in improving the credibility of greenhouse gas inventory in waste incineration sector.

• Environmental and Resource Economics Review
• /
• v.30 no.2
• /
• pp.269-297
• /
• 2021

Bioplastics are attracting attention as a substitute for conventional petroleum-based plastics because they are carbon neutral and can be biodegradable. This study estimated economic and environmental impact of regulating the petroleum-based plastics industry and fostering the bioplastics industry using a Recursive Dynamic CGE Model of the Korean Economy. Results show that the regulation of the conventional plastics industry exhibits a positive environmental impact by reducing greenhouse gases and plastic waste and a negative economic impact with a decrease in GDP. Meanwhile, fostering the bioplastics industry with regulation on conventional plastics industry has similar levels of greenhouse gas and waste reduction effects when there is only regulation on the conventional plastics industry. It is also shown that expanding the production of bioplastics industry offsets existing economic losses as a form of increased GDP. If petroleum-based plastics are replaced through the expansion of bioplastics production, it can contribute to the decoupling of greenhouse gas emissions and plastic waste from economic growth.

• Journal of ILASS-Korea
• /
• v.28 no.1
• /
• pp.43-48
• /
• 2023

The waste-heat-recovery boiler with water spray (HR-B/WS) applies the heat exchange between the inlet air and exhaust gas with the water spray into the inlet air. The evaporation of water in the inlet air promotes heat recovery from the exhaust gas so that thermal efficiency can be improved by the enhanced condensing effect. The NOx emission can also be reduced by lowering the flame temperature due to the dilution effect of the water. In this study, the validity of this concept is examined by the practical boiler test performed with a 24 kW condensing boiler under the full load condition according to the water injection amount. The theoretical amount of water injection is calculated under the assumption of full evaporation of the sprayed water, which is calculated as 50 g/min. Since the injected water cannot evaporate fully in the actual system, the maximum water spray amount is set as 100 g/min. The results showed that the water injection can increase the thermal efficiency up to 95.59% and reduce NOx and CO emissions simultaneously to 8.9 ppm and 35 ppm at 0% of O₂. Although the heat energy loss increased due to the unevaporated water, the increase in water injection amount caused higher thermal efficiency due to the increased amount of the evaporated water.

• KSBB Journal
• /
• v.29 no.6
• /
• pp.399-404
• /
• 2014

Production of biodegradable polymer polyhydroxyalkanoates (PHAs) from industrial wastes exhibits several advantages such as recycle of waste and the production of high valuable products. To this end, this study aimed at isolating from the sewage treatment plant a PHA producing bacterium capable of utilizing wastes generated from biodiesel and food industries. A Bacillus cereus strain capable of producing poly(3-hydroxybutyrate) [P(3HB)] was isolated, which was followed by confirmation of P(3HB) accumulation by gas-chromatographic analyses. Then, the effects of nutrient limitation on P(3HB) production by B. cereus was first examined. Cells cultured in a minimal medium under the limitation of nitrogen, potassium and sulfur suggested that nitrogen limitation allows the highest P(3HB) accumulation. Next, production of P(3HB) was examined from both waste of biodiesel production (crude glycerol) and waste from food industry (spent coffee grounds). Cells cultured in nitrogen-limited minimal medium supplemented crude glycerol and waste spent coffee grounds extract accumulated P(3HB) to the contents of 2.4% and 1.0% of DCW. This is the first report demonstrating the capability of B. cereus to produce P(3HB) from waste raw materials such as crude glycerol and spent coffee grounds.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.7 no.2
• /
• pp.47-55
• /
• 1999

Recently, the treatment of that wastes according to increase of food waste has been a great problem of modern society for long time. This study was aimed to evaluate possibility for food waste and sewage sludge mixture treatment using pilot scale two-phase anaerobic digester. Pilot scale two-phase anaerobic digestion system was performanced at 1 : 9 mixture ratio of food waste and sewage sludge infield. The detention time of digester was 20days. The average COD and VS removal efficiencies in organic loading rate $3.03kg\;TCOD/m^3-day$ were 57.7 and 47.7%, and the gas production rate and methane content were $0.4m^3/kg$ VS-day and 65.3%, respectively. TS, VS and VS/TS(%) of mixing tank were 4.44%, 2.59% and 58.34%, respectively and TS. VS and VS/TS(%) of digester in steady state were 3.32%, 1.39% and 41.90%, respectively, Through this study. it was possible to accomplish effective mixture treatment of the sewage sludge and food waste.

• Journal of the Korean Chemical Society
• /
• v.62 no.6
• /
• pp.433-440
• /
• 2018

The pyrolysis has been universally applied to recycle the waste artificial marble. However, the existing heat treatment equipment has relatively low heat transfer efficiency into the inner part of the waste artificial marble. Besides, it leads to unnecessary excessive gas during the partial carbonization of the polymethyl methacrylate (PMMA) and raises the risk of fire due to heat at an extremely high temperature. This study suggests the process of pyrolysis at the formation state after adding the starch to waste artificial marble to overcome above-mentioned problems. As the result of experiments, this method showed that the pyrolysis of waste artificial marble was greatly improved at comparatively low temperature condition of $350^{\circ}C$. Moreover, it also manifested the effect on securing the stability and energy savings necessary for the recovery of methyl methacrylate (MMA) and ${\alpha}$-alumina (${\alpha}-Al_2O_3$).

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.8 no.2
• /
• pp.143-150
• /
• 2010

Vitrification technology has been gradually recognized as one of effective solidification methods for concentrated boric acid wastes generated in PWR. Vitrification for low- and intermediate-level radioactive wastes has a large volume reduction and good durability for the final products. A feasibility study for the vitrification of concentrated boric acid wastes has been performed with developing the pre-treatment methods of powdered wastes, glass compositions using glass formulation and demonstration test. The pre-treatment method is pelletizing the powder type for stable feeding within cold crucible melter. The glass compositions should be developed considering molten glass are related with wastes reduction. High contents of sodium and boron within borate wastes give influence to waste loading. A variety of factors obtained from the demonstration test are reviewed, which is wastes feeding rate, off-gas characteristics on stack and glass characteristics of final products such as durability for implementing the wastes disposal requirement. The aim of this paper is to present the feasibility of vitrification and review the solidification method for concentrated boric acid wastes and obtain the physicochemical characteristics of solidified glass.

• Resources Recycling
• /
• v.9 no.6
• /
• pp.23-30
• /
• 2000

Since most of the waste plastics are incinerated and landfilled for the plastic treatment, the environmental friendly processes must be introduced. The plastic utilization of plastic to the blast furnace as a substitutional fuel was developed as a useful recycling method of waste plastics, and commercialized in several ironmaking company in Europe and Japan. Present study was carried out to understand the effect of plastic injection on blast furnace process continuously by using the foundry blast furnace in POSCO. The coke replacement ratio turned out to be 0.98 with the waste plastic injection up to 13.8 kg/thm of injection rate, and there were no significant effect of the kinds of injection plastics on the replacement ratio in this test operation. The permeability in the furnace became worse and the heat load in the lower part of blast furnace was increased with increasing the injection rate of waste plastics. As the rate of plastic injection were increased, the top gas utilization and shaft efficiency were also decreased from the Rist diagram analysis.

• Proceedings of the Korean Environmental Sciences Society Conference
• /
• 2019.10a
• /
• pp.134-134
• /
• 2019

Utilization of organic waste as a renewable energy source is promising for sustainability and mitigation of climate change. Pyrolysis converts organic waste to gas, oil, and biochar by incomplete biomass combustion. Biochar is widely used as a soil conditioner and adsorbent. Biochar adsorbs/desorbs metals and ions depending on the soil environment and condition to act as a nutrient buffer in soils. Biochar is also regarded as a carbon storage by fixation of organic carbon. Phosphorus (P) and nitrogen (N) are strictly controlled in many wastewater treatment plants because it causes eutrophication in water bodies. P and N is removed by biological and chemical methods in wastewater treatment plants and transferred to sludge for disposal. On the other hand, P is an irreplaceable essential element for all living organisms and its resource (phosphate rock) is estimated about 100 years of economical mining. Therefore, P and N recovery from waste and wastewater is a critical issue for sustainable human society. For the purpose, intensive researches have been carried out to remove and recover P and N from waste and wastewater. Previous studies have shown that biochars can adsorb and desorbed phosphates implying that biochars could be a complementary fertilizer. However, most of the conventional biochar have limited capacity to adsorb phosphates and nitrate. Recent studies have focused on biochar impregnated with metal salts to improve phosphates and nitrate adsorption by synthesizing biochars with novel structures and surface properties. Metal salts and metal oxides have been used for the surface modification of biochars. If P removal is the only concern, P adsorption kinetics and capacity are the only important factors. If both of P and N removal and the application of recovery are concerned, however, P and N desorption characteristics and bioavailability are also critical factors to be considered. Most of the researches on impregnated biochars have focused on P removal efficiency and kinetics. In this study, coffee waste is thermally treated to produce biochar and it was impregnated with Mg/Al to enhance phosphates and nitrate adsorption/desorption and P bioavailability to increase its value as a fertilizer. Kinetics of phosphates and nitrate adsorption/desorption and bioavailability analysis were carried out to estimate its potential as a P and N removal adsorbent in wasewater and a fertilizer in soil.