• 한국자동차공학회논문집
• /
• 제5권5호
• /
• pp.51-66
• /
• 1997

A heat transfer model of the intake valve in a spark ignition engine is presented, which is calibrated with a number of the valve temperature profiles measured during engine warm-up for the gaseous fuel(propane). The valve is divided into four identical elements for which the assumption of lumped thermal mass is applied. The calibration is made so that the difference between the measued and simulated valve temperatures becomes minimal. Then the model is applied to the cases of the liquid fuel(indolene) to estimate the amount of the liquid fuel vaporized from the intake valve by assuming that fuel evaporation accounts for the deficit of the heat balance budget. The results of the model show quantitative contribution of each heat transfer source to the heat balance. The behavior of the calculated mass fraction of the fuel vaporized from the intake valve explains how the liquid fuel evaporate during engine warm-up. The mass fraction at warmed-up condition is closely related with the fraction directly targeted on the valve back by the fuel spray geometry.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2000년도 추계학술대회 논문집
• /
• pp.168-173
• /
• 2000

The limiting drawing ratio (LDR) under uniform heating of blanks was measured at the various temperature ranges between 25 and $250^{\circ}C$ by using two different blank shapes, square and circular blanks, and six different blank sizes with the drawing ratios(DR) of 2.4 to 2.9. The galvannealed steel sheet (SCP3CM 60/60) of 0.7mm thickness was used. The LDR at warm forming condition reached 1.2 times of that at room temperature, and the maximum drawing depth reached 1.9 times. The higher temperature was adopted, the more stable and uniform thickness strain distribution was observed.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2000년도 춘계학술대회논문집
• /
• pp.67-70
• /
• 2000

The tool life is not long enough under sever forming condition in warm forging. The tool life is affected by wear heat fatigue plastic deformation and so on. Especially wear is one of the most serious factors for tool life. To increase tool life we should consider various factors like processing design die design die materials lubrication and cooling system This study design to obtain the steady state temperature of die by FEM analysis under several conditions of cooling. There are four cooling conditions in this study no cooling internal cooling external cooling and both internal and external cooling. With above obtained temperatures tool life is predicted using Archard's model that is considered softening of die. The effect of internal cooling system is better than that of externally cooled die. To predict the die life the steady state temperature is calculated by using mean temperature of die. Considering only wear the die life much longer as the cooling effect is bigger. The more accurate die life will be predicted if we consider heat crack as well as wear.

• 소성∙가공
• /
• 제11권5호
• /
• pp.423-429
• /
• 2002

The limiting drawing ratio (LDR) under uniform heating of blanks was measured at the various temperature ranges between 25 and 25$0^{\circ}C$ by using two different blank shapes, square and circular blanks, and six different blank sizes with the drawing ratios(DR) of 2.4 to 2.9. The galvannealed steel sheet (SCP3CM 60/60) of 0.7mm thickness were used. The LDR at warm forming condition reached 1.2 times of that at room temperature, and the maximum drawing depth reached 1.9 times. The higher temperature was adopted, the more stable and uniform thickness strain distribution was observed. Some cases of the experimental results were compared with the analitical results using the commercial finite element method (FEM) code.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2007년도 추계학술대회 논문집
• /
• pp.306-309
• /
• 2007

Recently, magnesium alloys have been widely used in automotive, aerospace and electronic industries with the advantages such as lightweightness, high specific strength and stiffness. However, magnesium alloy has quite low formability at room temperature due to its hexagonal close-packed crystal structure. Warm deep drawing is one of the forming technologies to improve the formability of magnesium alloy sheet and the lubrication condition is an important process parameter in that. In this study, the drawing tests of AZ31 alloy sheet at elevated temperature for various kinds of lubricant were carried out and the effects of lubrication conditions on drawbility were investigated.

• 한국분말재료학회지
• /
• 제13권1호
• /
• pp.52-56
• /
• 2006

The aim of this work was to establish an optimal condition for determination of apparent density and flow rate for warm compacting powder. For this purpose it was evaluated uncertainty on them according to ISO Guide to the Expression of Uncertainty in Measurement. This evaluation example would be useful even in powder fluidity measurement at room temperature.

• 동의생리병리학회지
• /
• 제19권5호
• /
• pp.1191-1194
• /
• 2005

The aim of this study was to investigate the change of Heart Rate Variability(HRV) that mild cold stimulus on the forehead of healthy men induces. 34 healthy male subjects participated in the experiments. On the first test series, 15 subjects were applied to the mild cold stimulus by the devise for cold stimulation. In the second test series, 10 subjects With heat Syndrome and 5 subjects With cold Syndrome were applied to the mild cold Stimulus. Aa a additional test, 4 subjects with cold syndrome were applied to the warm stimulus in the last test series. We analyzed the HRV through measuring electrocardiogram.(ECG). The result of this study is comparatively clear. In the first test series, mild cold stimulus made parasympathetic nervous system be activated. In the second test series, mild cold stimulus made parasympathetic nervous system be activated both in subjects with heat syndrome and subjects with cold syndrome, and heat syndrome shows more active parasympathetic nervous system rather than cold syndrome subjects do. In the last test series, 2 subjects with cold syndrome respond the mild cold stimulus. That means warm stimulus of cold condition subjects made parasympathetic nervous system active in 2 of 4 subjects. We found out that mild cold stimulus on forehead makes parasympathetic nervous system be activated in healthy male, and it can be interpreted that mild cold stimulus make healthy human be relaxed. Also, subjects have different fondness of thermal stimulus according to their Cold or Heat condition Preferences. Last test series shows that we need to investigate effect of the warm stimulus heat syndrome subjects.

• 혜화의학회지
• /
• 제9권1호
• /
• pp.319-335
• /
• 2000

According to the literatual study on the external medical trearment of Menorrhalgia and Leucorrhea for gynecologic condition, the results were as follows. 1. Using external medical treatment for Menorrhalgia is to insert vagina theraphy, fumigation theraphy, to wash vagina theraphy, to insert anus theraphy, to apply hot pack theraphy and use with suppository such as BANSUKHWAN(礬石丸), SASANGZASAN(蛇床子散), KUMBONGHYUNGJU(金鳳衡珠) 2. Using external medical treatment for Leucorrhea is washing and fumigation on vagina, to wash vagina, to insert vagina, cleansing theraphy and use with Suppository such as YONGYEOMGO(龍鹽膏), KAMISASANGJASAN(加味蛇床子散), SASANGSACHUNGSEJE(蛇床子洗劑). 3. ANGELICAE GIGANTIS RADIX (當歸) is in mostly general use for external medical treatment of Menorrhalgia and Leucorrhea, in that order ANSU SEMEN(杏仁), EVODIAE FRUCTUS(吳茱萸), TORILIS FRUCTUS (蛇床子), CORYDALIS TUBER(玄胡索), CINIAMOMI CORTEX(肉桂), CARYOPHYLLI FLOS(丁香), ALUMEN(枯白礬), AQUILARIAE LIGNUM (沈香). 4. The efficacy of medicines to use external medical treatment is as follow to help circulation of blood, to warm spleen and stomach, to warm blood, to warm uterus and remove cold, to remove heat and dry moisture, to down heat-product, to contract bloodvessel, to counteract poison and destory virus, to make energy and blood. 5. KUMBONGHYUNGJU, made same size as cherry and shape vagina medicine, use for Menorrhalgia, menstural irregularity, Leucorrhea, it has the efficacy as follow to remove cold and dry moisture, to warm uterus, to help circulation and romove pain, to down moisture-heat.

• 소성∙가공
• /
• 제14권8호통권80호
• /
• pp.655-660
• /
• 2005

• 한국농공학회논문집
• /
• 제50권3호
• /
• pp.105-112
• /
• 2008

Solar energy, which is one of renewable energy, would be the most useful resources that can be applied to making energy recycling villages without using fossil energy. This study analyzed energy potential on solar energy considering weather condition in three traditional villages and compared with energy consumption surveyed. A photovoltaic system having 3.0kWp capacity of unit module can generate 182.5%, 96.1% and 170.9% of the yearly mean consumption of electric power in Makhyun, Boojang, and Soso, respectively. A flat-plate solar collector having $2.64m^2$ area of unit module can generate warm water of $142{\ell}$/day, $89{\ell}$/day, and $173{\ell}$/day, respectively in three study villages. In Makhyun and Soso, photovoltaic power and warm water produced by solar energy were sufficient to supply required amount of electric power and warm water. However, both electric power and warm water produced by unit solar module were not sufficient in Boojang area, and so it is required to increase the module area by more than 50%. According to the results of this study, the appropriate combination of energy resources can be applied to rural green-village planning if the characteristic of energy potential for each local area is considered.