• Progress in Superconductivity
• /
• 제8권2호
• /
• pp.127-131
• /
• 2007

We have measured the Hall conductivity (${\sigma}_{xy}$) of c-axis-oriented $MgB_2$ thin films as functions of temperatures and magnetic fields. We found that the Hall conductivity (${\sigma}_{xy}$) is expressed by the sum of two terms, ${\sigma}_{xy}=C_l/H+C_3H$, where the coefficient $C_1\;and\;C_3$ are independent of the magnetic fields and have positive values. The coefficient $C_1$ is strongly dependent on the temperature, while the $C_3$ is weakly dependent on the temperature. We have obtained that the $C_1$ is proportional to $(1- T/T_c)^n$ with n = 4.2, which is consistent with the data observed in $La_{2-x}Sr_xCuO_4$ superconductors with low anisotropy ratio.

• Progress in Superconductivity
• /
• 제13권2호
• /
• pp.117-121
• /
• 2011

We have fabricated $FeSe_x$ superconducting thin films at much different substrate temperatures of 430 and $610^{\circ}C$ on $Al_2O_3$(0001) substrates by using a pulsed laser deposition (PLD) technique. Superconducting transitions for both films were shown around 10 K, but their transition width and growth directions of grains were different. We found that superconducting tetragonal FeSe phases and non-superconducting hexagonal FeSe phases were coexisted in the sample grown at the low temperature of $430^{\circ}C$, whereas the hexagonal FeSe phase was decreased with increasing fabrication temperatures.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 하계학술대회 논문집 Vol.7
• /
• pp.321-322
• /
• 2006

The electrical properties of PZT thin film capacitor on TiN/W plug structure were investigated for high density ferroelectric memory devices. In order to enhance the ferroelectric properties of PZT capacitor, the process conditions of bottom electrodes were optimized. The fabricated PZT capacitor on TiN/W plug showed good remanent polarization, leakage current, and contact resistance of TiN/W plug, which were $33\;{\mu}C/cm^2$, $1.2{\times}10^{-6}\;A/cm^2$, and 5.3 ohm/contact, respectively.

• E2M - 전기 전자와 첨단 소재
• /
• 제8권1호
• /
• pp.21-26
• /
• 1995

Highly sensitive and mechanically stable gas sensors have been fabricated using the microfabrication and micromaching techniques. The sensing material used to detect the offensive trimethylarnine ((CH$_{3}$)$_{3}$N) gas is 6 wt% $Al_{2}$O$_{3}$-doped, 1000.angs.-thick ZnO deposited by r. f. magnetron sputtering. The optimum operating temperature of the sensor is 350.deg.C and the corresponding heater power is about 85mW. Excellent thermal insulation is achieved by the use of a double-layer structure of 0.2.mu.m -thick silicon nitride and 1.4.mu.m-thick phosphosilicate glass(PSG) prepared by low pressure chemical vapor deposition(LPCVD) and atmospheric pressure chemical vapor deposition(APCVD), respectively. The sensors are mechanically stable enough to endure at least 43, 200 heat cycles between room temperature and 350.deg. C.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1996년도 하계학술대회 논문집 C
• /
• pp.1428-1430
• /
• 1996

Thin Silicon oxynitride(SiON) films have been chemically deposited using 193nm ArF Excimer Laser CVD, with $Si_{2}H_{8}$, $N_{2}O$, and $NH_3$ as the reactive gases and $N_2$ as the carrier gas. Experimental results show that deposition rate and refractive index have a strong dependence on substrate temperature, chamber pressure, gas ratio, laser power and laser beam height. Electrical characterization of oxynitride films demonstrates that for $NH_{3}/N_{2}O$ flow ratios ranging from 0.25 to 1, the leakage currents, the interface trap density and the capacitances (dielect ric constant) increase and the dielectric breakdown fields decrease

• 한국진공학회지
• /
• 제4권S2호
• /
• pp.131-138
• /
• 1995

The broad beam ion sources of hot filament plasma type have widely used for modifications of materials and thin films, and the new type intensive current broad beam metal ion source including reactive gaseous ion beams is needed for preparing the hard coating films such as DLC, $\beta-C_3N_4$ Carbides, Nitrides, Borides etc. Now a electorn beam evaporation(EBE) broad beam metal ion source has been developed for this purpose in our lab. CN film has been formed by the EBE ion source. Study of the CN film shows that it has high hardness(HK=5800kgf/$\textrm {mm}^2$)and good adhesion. This method can widely changes the ratio of C/N atom's concentrations from 0.14 to 0.6 and has high coating rate. The low energy pocket ion source which was specially designed for surface texturing of medical silicon rubber was also developed. It has high efficiency and large uniform working zone. Both nature texturing and mesh masked texturing of silicon rubbers were performed. The biocompatibility was tested by culture of monocytes, and the results showed improved biocompatibility for the treated silicon rubbers. In addition, the TiB2 film synthesized by IBED is being studied recently in our lab. In this paper, the results which include the hardness, thickness of the films and the AES, XRD analysis as well as the tests of the oxidation of high temperature and erosion will be presented.

• 한국전기전자재료학회논문지
• /
• 제19권7호
• /
• pp.624-630
• /
• 2006

ZnO deposition parameters are not independent and have a nonlinear and complex property. To propose a method that could verify and predict the relations of process variables, neural network was used. At first, ZnO thin films were deposited by using RF magnetron sputtering process with various conditions. Si, GaAs, and Glass were used as substrates. The temperature, work pressure, and RF power of the substrate were $50\sim500^{\circ}C$, 15 mTorr, and $180\sim210W$, respectively : the purity of the target was ZnO 4 N. Structural properties of ZnO thin films were estimated by using XRD (0002) peak intensity. The structure of neural network was a form of 4-7-1 that have one hidden layer. In training a network, learning rate and momentum were selected as 0.2, 0.6 respectively. A backpropagation neural network were performed with XRD (0002) peak data. After training a network, the temperature of substrate was evaluated as the most important parameter by sensitivity analysis and response surface. As a result, neural network could capture nonlinear and complex relationships between process parameters and predict structural properties of ZnO thin films with a limited set of experiments.

• Progress in Superconductivity
• /
• 제3권1호
• /
• pp.45-48
• /
• 2001

We have fabricated $MgB_2$thin films on (1 1 02)$ A1_2$$O_3$substrates by using a two-step method. Amorphous B thin films were deposited by a pulsed laser deposition technique and sintered in Mg vapor at various temperatures from 800 to $950^{\circ}C$. Superconducting properties of the thin films were investigated by temperature dependences of magnetization and critical current density. Structural studies were carried out by an x-ray diffraction and a scanning electron microscope. The films fabricated at $900^{\circ}C$ showed the highest transition temperature of 39 K and critical current density of ~$10^{7}$ A/$\textrm{cm}^2$ at 15 K.

• 한국결정성장학회지
• /
• 제15권6호
• /
• pp.252-259
• /
• 2005

[ $CuGaSe_2$ ] 단결정 박막은 수평 전기로에서 합성한 $CuGaSe_2$ 다결정을 증발원으로하여, hot wall epitaxy(HWE) 방법으로 증발원과 기판(반절연성 GaAs(100))의 온도를 각각 $610^{\circ}C,\;450^{\circ}C$로 고정하여 단결정 박막을 성장하였다. 이때 단결정 박막의 결정성은 광발광 스펙트럼(PL)과 이중결정 X-선 요동곡선 (DCRC)으로부터 구하였다. Hall 효과는 Van der Pauw 방법에 의해 측정되었으며, 293 K에서 운반자 농도와 이동도는 각각 $4.87{\times}10^{17}/cm^3,\;129cm^2/V{\cdot}s$였다. $n-Cds/p-CuGaSe_2$ 합 태양전지에 $80mW/cm^2$의 광을 조사시켜 최대 출력점에서 전압은 0.41 V, 전류밀도는 $21.8mA/cm^2$였고, fill factor는 0.75 그리고 태양전지 전력변환 효율은 11.17% 였다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 추계학술대회 논문집
• /
• pp.113-113
• /
• 2009

This paper describes the characteristics of a poly 3C-SiC micro heater which was fabricated on $AlN(0.1{\mu}m)/3C-SiC(1.0{\mu}m)$ suspended membranes by surface micro- machining technology. The 3C-SiC and AlN thin films which have wide energy bandgap and very low lattice mismatch were used sensors for high temperature and voltage environments. The 3C-SiC thin film was used as micro heaters and temperature sensor materials simultaneously. The implemented 3C-SiC RTD (resistance of temperature detector) and the power consumption of micro heaters were measured and calculated. The TCR (thermal coefficient of the resistance) of 3C-SiC RTD is about -5200 $ppm/^{\circ}C$ within a temperature range from $25^{\circ}C$ to $50^{\circ}C$ and -1040 $ppm/^{\circ}C$ at $500^{\circ}C$. The micro heater generates the heat about $500^{\circ}C$ at 10.3 mW. Moreover, durability of 3C-SiC micro heaters in high voltages is better than pt micro heaters. A thermal distribution measured and simulated by IR thermovision and COMSOL is uniform on the membrane surface.