• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.11 no.5
• /
• pp.586-592
• /
• 2018

In this paper, HIC with various functions is proposed for the design 140W LED power control circuit. The proposed HIC integrates constant voltage/constant current circuit, short circuit protection circuit, internal constant voltage circuit, and dimmer circuit, thereby reducing the horizontal length of the PCB by 16% comparing with the conventional system. Through various experiments, we verified the performance of each block implemented inside of HIC with numerical results. (Constant voltage variation ratio: 2.9%, dimmer circuit duty variation within 5%, stable short protection at 720 mA) Since the PCB area can be significantly reduced by applying the proposed HIC. It is possible to reduce the PCB manufacturing time which takes up most of the manufacturing time, however, It is expected that the faulted power module can be replaced without replacing the whole PCB, so that maintenance / repair can be made easier.

• Journal of Bio-Environment Control
• /
• v.27 no.3
• /
• pp.260-268
• /
• 2018

The aim of this study was to evaluate the effect of light quality using either monochromatic or combined LEDs on the growth and antioxidant accumulation of Agastache rugosa cultivated under hydroponics for 4 weeks. This experiment was performed in a controlled-environment room at $22{\pm}1^{\circ}C$ and $18{\pm}1^{\circ}C$ (day and night temperatures, respectively) and 50-70% relative humidity, with a provided photosynthetic photon flux density (PPFD) of $180{\pm}5{\mu}mol{\cdot}m^{-2}{\cdot}s^{-1}$ and irradiated with either monochromatic (W10 and R10) or mixed LEDs (W2B1G1, R3B1, R2B1G1, and W2B1G1) with a differing ratio of each LED's PPFD and fluorescent lighting (FL: control) with a 16/8 h photoperiod. Fresh and dry weights were highest for plants grown under the W2B1G1 treatment. A. rugosa grown with R10 had the greatest plant height but the lowest SPAD among all treatments. The concentration of rosmarinic acid in plants grown under W2B1G1 was significantly higher than that of plants grown under other treatments. Tilianin content was significantly higher in R3B1 than in the other treatments. However, whole-plant rosmarinic acid and tilianin content was the highest under the W2B1G1 condition. To cultivate A. rugosa in a plant factory, mixed-LED light conditions with W2B1G1 is considered to be more advantageous for the growth and antioxidant accumulation of A. rugosa. It is though that the total whole-plant antioxidant content is more crucial for commercial use; the present study demonstrates the potential to achieve higher content of functional materials in plants through the selection of light quality.

• Electronics and Telecommunications Trends
• /
• v.24 no.5
• /
• pp.30-37
• /
• 2009

LED는 빛을 내는 반도체이다. LED는 백열전등에 비하여 전기 절감 효과가 높고, 형광 등에 비하여 수은을 사용하지 않아 친환경적이기 때문에 녹색성장의 대표주자 중 하나이다. 메모리 반도체와 전자통신 기기가 융합하여 지난 20년간 발전하여 왔듯이, 앞으로는 LED와 전자통신이 융합하여 새로운 형태의 융합 기술이 발전할 것이다. 현재 예상 가능한 LED 전자통신 융합 기술은 LED 조명과 동시에 통신을 할 수 있는 가시광 무선통신 기술과 감성 및 전기 절감을 실현할 수 있는 LED 조명 모듈간 유선 네트워킹 기술이다. 본 고에서는 LED 조명과 녹색성장이 연계된 배경, 가시광 무선통신의 국내 및 국제 표준 동향, LED 조명 네트워킹 기술을 설명한다. LED 융합 기술에 의하여 인간중심의 편리 시설을 제공하면서도 전기 절감 및 저탄소를 실현할 수 있다.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.24 no.12
• /
• pp.38-46
• /
• 2010

For the development of 100[W] stage lighting, quantitative and uniform color mixing that applied through color adopted Simple-Inverse matching so that color mixing can be possible along Black Body Locus. R,G,B(Red, Green, Blue) LED(Light Emitting Diode) arrangement through LED package character analysis, LED module, and the characteristic of device were considered for uniform color mixing. A distance changeable optical device was built to assure high uniformity and high diffusion of not only the middle of diffusion side but also the border side. Also, we developed the control power circuit that can expand up to 6 channels which are possible for quantitative color mixing, and the high uniformity and high quantified border light for color mixing control and the verification of color mixing characteristics by composing GUI(Graphical user interface) including color mixing simulator. By presenting the experimental results of light color control, we proved the usefulness of our developed border light and the proposed color mixing method.

• Journal of IKEEE
• /
• v.22 no.3
• /
• pp.742-746
• /
• 2018

In this paper, we implemented a VLC(Visible Light Communication) system capable of transmitting/receiving data on a 30MHz clock based on On/Off keying modulation/demodulation. The data rate of the implemented system can be verified by functional verification of VLC channel composed of LED/photodiode driver and VLC transmitting/receiving signal of Tx/Rx platform. But, In the experimental results with the VLC transmitting/receiving for combined module, the maximum transmission rate was measured at 15 MHz. Therefore, we describe the problems that can occur when implement the VLC system using the LED module with output power of 15W or more and propose ways to improve it.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.25 no.1
• /
• pp.53-57
• /
• 2012

In this paper, by designing 20 W class driving circuit for driving high-power LED (Light Emitting Diode), we are going to comparatively carry out the analysis of characteristics for power circuit according to each design method. In this case, 200 V 60 Hz was performed as input data. The electrical characteristics such as voltage, current and ripple are checked for constant current circuit and constant voltage circuit in the LED module. In addition, as the ripple has an influence on illumination of LED light, low temperature working (-20 [$^{\circ}C$]) and high temperature working(80 [$^{\circ}C$]) are measured to make sure the ripple characteristics in accordance with temperature. In low temperature operation -20 [$^{\circ}C$] measurements, both constant current circuit and constant-voltage circuit were less impacted on input fluctuation, whereas in the high temperature operation 80 [$^{\circ}C$], current voltage in constant voltage circuit was surge after 430 [hour]. Voltage current ripple of constant current circuit was much less than constant voltage circuit, therefore we can show that constant current circuit is more stable.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2008.05a
• /
• pp.205-208
• /
• 2008

In this paper, we have measured and compared the optical and electrical characteristics of LED(light emitting diode) and CNT(carbon nano-tube) lightings. Especially, the IES format files are used for each of the luminaire LlD(luminous intensity distribution) analysis and light level simulation for analyze the maximum, minimum, and average light level. In the future, when CNT and the LED based lighting technology standards are writing, this data will be used in judging.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.16 no.5
• /
• pp.150-156
• /
• 2017

This study tests the characteristics of heat radiation by applying the pin-height variables to 30-W LED floodlights. The angle of the heat sink enables us to identify the characteristics of the heat radiation based on the temperature distribution. The results of the study are as follows. When the heat sinks are set towards the ground, the heat transfer decreases in speed only to expands the temperature distribution, which adversely affects the characteristics of heat radiation and expands the temperature distribution of PCB with the LED chip. We verify that the characteristics of heat radiation are adversely affected when the height of the cooling pin decreases and the heat radiation area decreases, which impedes the heat transfer and increases the temperature distribution on the heat sink.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.18 no.5
• /
• pp.96-102
• /
• 2019

This study investigated the heat dissipation characteristics of a heat-sensitive LED. More than 80% of the power supply is converted into heat energy, which has a fatal impact on the lifetime of the LED. Therefore, the effective heat dissipation characteristics of a heatsink, such as a 30W floodlight, through forced convection were grasped and the heat transfer characteristics were tested. As a result, it was confirmed that the smaller the number of fins, the more the temperature distribution varies according to the wind velocity. In addition, the larger the number of fins, the smaller the temperature difference according to the wind velocity. Therefore, it was found through this experiment that excellent heat dissipation performance was exhibited as the heat dissipation area and wind velocity increased.

• Journal of the Semiconductor & Display Technology
• /
• v.20 no.3
• /
• pp.32-38
• /
• 2021

We developed an inductively coupled plasma (ICP) etcher for GaN etching using a parallel plasma electrode source with a multifunctional chuck matched to it in order for the low power consumption and low process cost in comparison with the conventional ICP system with a helical-type plasma electrode source. The optimization process condition using it for the micro light-emitting diode (µ-LED) chip fabrication was established, which is an ICP RF power of 300 W, a chuck power of 200 W, a BCl₃/Cl₂ gas ratio of 3:2. Under this condition, the mesa structure with the etch depth over 1 ㎛ and the etch angle over 75° and also with no etching residue was obtained for the µ-LED chip. The developed ICP showed the improved values on the process pressure, the etch selectivity, the etch depth uniformity, the etch angle profile and the substrate temperature uniformity in comparison with the commercial ICP. The µ-LED chip fabricated using the developed ICP showed the similar or improved characteristics in the L-I-V measurements compared with the one fabricated using the conventional ICP method