• Journal of the Korean Society of Visualization
• /
• v.21 no.3
• /
• pp.85-92
• /
• 2023

In this study, we present experimental results of cavitating flow around a vortex generator which is used to improve the flow in the wake of ships and enhance propulsion efficiency. We conducted experiments at the CNU cavitation tunnel on a total of six vortex generators, two different aspect ratios and three taper ratios. We recorded cavity patterns using a high-speed camera and quantitatively evaluated cavity fraction using OpenCV. The most important finding of this study is that the vortex cavity generated at a root leading edge of the vortex generator develops at a specific angle.

• Journal of the Korean Society of Visualization
• /
• v.20 no.3
• /
• pp.128-135
• /
• 2022

Cavitation occurs inevitably in marine propellers rotating at high speed in the water, which is a major cause of underwater radiated noise. Cavitation-induced noise from propellers rotating at a specific frequency not only reduces the sonar detection capability, but also exposes the ship's location, and it causes very fatal consequences for the survivability of the navy vessels. Therefore cavity inception speed (CIS) is one of the important factors determining the special performance of the ship. In this study, we present a method using computer vision that can detect and quantitatively estimate tip vortex cavitation on a propeller rotating at high speed. Based on the model test results performed in a large cavitation tunnel, the effectiveness of this method was verified.

• Journal of Ocean Engineering and Technology
• /
• v.32 no.4
• /
• pp.244-252
• /
• 2018

This paper provides quantification of the effects of the turbulence model and grid refinement on the analysis of tip vortex flows by using the RANS(Reynolds averaged Navier-Stokes) method. Numerical simulations of the tip vortex flows of the NACA $66_2$-415 elliptic hydrofoil were conducted, and two turbulence models for RANS closure were tested, i.e., the Realizable $k-{\varepsilon}$ model and the Reynolds stress transport model. Numerical results were compared with available experimental data, and it was shown that the data for the Reynolds stress transport model that were computed on the finest grid system had better agreement in reproducing the development and propagation of the tip vortex. The Realizable $k-{\varepsilon}$ model overestimated the turbulence level in the vortex core and showed a diffusive behavior of the tip vortex. The tip vortex cavitation on the hydrofoil and its trajectory also showed good agreement between the current numerical results that were obtained using the Reynolds stress transport model and the results observed in the experiment.

• Journal of the Society of Naval Architects of Korea
• /
• v.45 no.1
• /
• pp.18-28
• /
• 2008

Fins are widely used for roll stabilization of passenger ferries and high performance naval ships, among others. In the present study, numerical simulations are performed to investigate the influence of end-plates upon the cavitation characteristics of a stabilizer fin for various angles of attack and speeds and the results are verified through a series of model experiments. It is found that a considerable retardation in tip vortex cavitation can be achieved with attachment of end-plates at the tip of the stabilizer fin. The results can be utilized for the design of stabilizer fins as well as the development of high performance control devices for ships.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.06a
• /
• pp.1027-1033
• /
• 2000

This paper describes the characteristics of vibration of a hydraulic turbine mainly due to cavitation occurrence. The analysis of vibration spectra of the turbine shaft shows that hub vortex cavitation occurs in the downstream of the turbine runner, which is verified from coherence analysis between shaft vibration displacement and dynamic pressure at the draft tube. Even though acceleration level measured at the guide vane lever, which is usually used for evaluation of cavitations performance, is decreased during forced aeration, it is found from the analysis of dynamic pressure spectra that cavitation around runner blades still remains unchanged. It is also found that lateral vibration of the turbine shaft is mainly due to the hub vortex cavitation of the turbine runner.

• Journal of the Society of Naval Architects of Korea
• /
• v.48 no.6
• /
• pp.501-508
• /
• 2011

In order to control the tip vortex cavitation occurring around the tip of a rotating propeller blade, researches on the propeller cavitation and blade tip vortex flows have been increased. In this paper, the propeller tip vortex flow for a blunt and sharp tips was studied using an unsteady Reynolds-averaged Navier-Stokes equations solver based on a cell-centered finite volume method. In numerical open water test, torques, thrusts, pressure distributions and vortex flows were compared for various rotating speeds. To consider a hull wake, the nominal wake was specified in inlet boundary condition. Pressure distributions and vortex flows with the hull wake were investigated for various propeller rotating angles. From the results, it was confirmed that the blunt tip propeller delayed the tip vortex flow.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.8 no.3
• /
• pp.219-227
• /
• 2016

Numerical simulation based on the Reynolds Averaged Naviere-Stokes (RANS) Computational Fluid Dynamics (CFD) method had been carried out with the commercial code ANSYS CFX. The structured grid and SST $k-{\omega}$ turbulence model had been adopted. The impact of non-condensable gas (NCG) on cavitation performance had been introduced into the Schnerr and Sauer cavitation model. The numerical investigation of cavitating flow of marine propeller E779A was carried out with different advance ratios and cavitation numbers to verify the numerical simulation method. Tip clearance effects on the performance of pumpjet propulsor had been investigated. Results showed that the structure and characteristics of the tip leakage vortex and the efficiency of the propulsor dropped more sharply with the increase of the tip clearance size. Furthermore, the numerical simulation of tip clearance cavitation of pumpjet propulsor had been presented with different rotational speed and tip clearance size. The mechanism of tip clearance cavitation causing a further loss of the efficiency had been studied. The influence of rotational speed and tip clearance size on tip clearance cavitation had been investigated.

• 한국전산유체공학회:학술대회논문집
• /
• 2011.05a
• /
• pp.592-595
• /
• 2011

A numerical investigation on a suction vortices, free vortices and subsurface vortices behavior in the model sump system with multi-intakes is performed A test model sump and piping system were designed based on Froude similitude for the prototype of the recommended structure layout by HI-9.B Standard for Pump Intake Design of the Hydraulic Institute. A numerical analysis of three dimensional multiphase flows through the model sump is performed by using the finite volume method of the CFX code with multi-block structured grid systems. A ${\kappa}-{\omega]$ ShearStressTransportturbulencemodelandthe Rayleigh-Plesset cavitation model are used for solving turbulence cavitating flow. From the numerical analysis, several types of vortices are reproduced and their formation, growing shedding and detailed vortex structures are investigated. To reduce abnormal vortices, an anti-vortex device is considered and its effect is investigated and discussed.

• International Journal of Fluid Machinery and Systems
• /
• v.3 no.1
• /
• pp.80-90
• /
• 2010

The cavity oscillation with swirling flow in hydraulic power generating systems was studied by a simple experiment and numerical simulation. Several types of fluctuation were observed in the experiment, including the cavitation surge caused by the diffuser effect and the vortex precession by the swirling flow. Both cavitation surge and vortex precession were simulated by CFD. Detailed flow structure was examined through flow visualization and CFD.

• Journal of the Society of Naval Architects of Korea
• /
• v.30 no.1
• /
• pp.94-103
• /
• 1993

This study deals with an investigation on the tip vortex generated by an elliptic wing with section shapes of NACA 0020. The flow structure on the wing surface is investigated by using tufts test as well as observing the cavitation pattern. The surface pressure on a foil surface is measured to complement the visualized flow field. Results show that a strong spanwise pressure gradient is a definite contributor on the formation of tip vorex, and the fluids from both sides contribute to the evolutionary process of tip vortex. On the other hand, a series of experiments are conducted to investigate the detailed structure of tip-vortex at various angles of attack. The tip-vortex formation and development are observed by producing a cavitation, and then by a laser sheet technique in conduction with a dye injection method. The shape of tip-vortex and the distance between a vortex core and the trailing vortex sheet are found to vary with the angle of attack. Overall features of tip flow are evaluated to complement the vortex model based on inviscid theory.