• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2018.05a
• /
• pp.35-36
• /
• 2018

According to the nation's greenhouse gas emission statistics, greenhouse gas emissions have been stiffly increasing. Accordingly, the importance of CO₂ reduction is more getting focused over the world. This trend makes the construction equipment be considered as a major target of reduction due to the large volume of emission. This study suggests the feasible methodology for estimating CO₂ emission from construction equipment and for being easily applied on the job sites. The methodology is based on the collection from the segmented CO₂ emission information of construction equipment. This study allows site personnels to estimate the total amount of CO₂ and to take appropriate actions for reasching the environmental regulations.

• Steel and Composite Structures
• /
• v.19 no.6
• /
• pp.1531-1548
• /
• 2015

The aim of this study is to investigate the relationship between Barcol hardness (H) and flexural modulus (E) degradation of composite sheets subjected to flexural fatigue. The resin transfer molding (RTM) method was used to produce 3-mm-thick composite sheets with fiber volume fraction of 44%. The composite sheets were subjected to flexural fatigue tests and Barcol scale hardness measurements. After these tests, the stiffness and hardness degradations were investigated in the composite sheets that failed after around one million cycles (stage III). Flexural modulus degradation values were in the range of 0.41-0.42 with the corresponding measured hardness degradation values in the range of 0.25-0.32 for the all fatigued composite sheets. Thus, a 25% reduction in the initial hardness and a 41% reduction in the initial flexural modulus can be taken as the failure criteria. The results showed that a reasonably well-defined relationship between Barcol hardness and flexural modulus degradation in the distance range.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.12
• /
• pp.3227-3235
• /
• 1994

This paper deals with an evaluation of the residual stress due to shot peening induced in a carburized gear tooth and its application to the fatigue crack propagation problem. A practical method is proposed on the basis of the assumption that the residual stress is caused by the difference of volume expansion in the case and the core, and the influence of both the reduction of retained austenite and the strain due to shot peening are considered. The evaluated residual stress is close to the measured stress, though the surface stress is rather overestimated. The stress intensity factor is computed by the influence function method, and it is shown that the factor is decreased by the residual stress in shot peened gear tooth. The shot peening is fairly effective to the reduction of fatigue crack growth rate. The crack propagation is simulated and the resistance due to shot peening is quantitatively demonstrated and discussed.

• Journal of Biomedical Engineering Research
• /
• v.41 no.1
• /
• pp.28-34
• /
• 2020

In this paper, we introduce motion artifact reduction algorithm for interleaved MRI using an advanced 3D approximation algorithm. The motion artifact framework of this paper is data corrected by post-processing with a new 3-D approximation algorithm which uses data structure for each voxel. In this study, we simulate and evaluate our algorithm using Shepp-Logan phantom and T1-MRI template for both scattered dataset and uniform dataset. We generated motion artifact using random generated motion parameters for the interleaved MRI. In simulation, we use image coregistration by SPM12 (https://www.fil.ion.ucl.ac.uk/spm/) to estimate the motion parameters. The motion artifact correction is done with using full dataset with estimated motion parameters, as well as use only one half of the full data which is the case when the half volume is corrupted by severe movement. We evaluate using numerical metrics and visualize error images.

• Journal of Information Display
• /
• v.12 no.2
• /
• pp.77-83
• /
• 2011

The memory compression algorithm CCC-LCP (color-count-controlled local color palette) reduces flicker in the liquid crystal display (LCD) overdrive. Its compression ratio is 1:5.4 for 10-bit images, with a 33 dB PSNR peak signal-to-noise ratio and with five times flicker reduction compared with the block truncation coding. The authors' two-alternative forced choice subjective tests proposed two new soundness properties, the 'CMP harmlessness' and 'OD non-lost (or OD liveliness)', to clarify the functional interaction between the overdrive functionality OD and the compression functionality CMP. The tests verified that CCC-LCP is practically applicable (at a 1.2H viewing distance threshold) for 42" 37-ppi WXGA TVs.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.3
• /
• pp.538-543
• /
• 2011

In this paper, design and control of an interleaved boost converter for multi-string PV Inverter are discussed. Interleaved Boost converter can reduce current ripples at input and output side by cancelling an each phase of inductor currents. Therefore, it contributes to increase efficiency and downsize the whole system volume, cost. One of the advantages of the multi-string system is easy to expand power capacity by connecting the converter modules in parallel. In order to reduce current ripples, the inductor currents on each phase are controlled independently in the converter module, and communication between the converter modules is required for further ripple current reduction. Current control algorithm for the balance of the each phase ripple currents and synchronization of the converter modules based on communication are proposed and implemented in the DSP programming. 10kW prototype of the multi-string converter module is assembled and experimental results are presented to verify the proposed ripple current reduction methods.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.4
• /
• pp.293-297
• /
• 1998

The influence of ion implantation on surface properties of polymers was studied. We investigated microhardness, friction, wear and wettablility of polyimide. Energies of 50, 200keV were used with doses range from $1{\times}10^{13} to 1{\times}10^{16} [ions/cm^2]$. The implanted ion species were B, N and Ar. The microhardness of polyimide was increased after implantation for doses of $1{\times}10^{15}\; [ions/cm^2]$. A reduction of the friction coefficient was in most case correlated with a reduction of wear. The contact angles of water for $B^+,N^+$ implanted polyimide decreased from $76^{\circ}C$ to zero, as the fluencies increased at energies of 50 and 200 KeV. However, the contact angle of Ar ion implanted polyimide did not change under ambient room conditions even if the time elapsed. SEM measurement was performed to characterize the modified surface layer.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.2090-2091
• /
• 2007

We investigated the characteristics of transformer type SFCL with neutral line. The transformer type SFCL having neutral line has achieved the simultaneous quench because the secondary winding has acted as parallel reactor. The fault current of SFCL was limited according to ratio of turn number between primary and secondary windings. Therefore, the power burden of superconducting element can be reduced by reduction of ratio of turn number between primary and secondary windings. As a result, we could expect reduction of it's volume in the transformer type SFCL.

• Fire Science and Engineering
• /
• v.11 no.2
• /
• pp.19-24
• /
• 1997

numerical simulation of unsteady heat conduction equation were carried out by finite control volume method using the gas temperature derived from fire model as a boundary value. The reduction of compressive and flexural by heating were calculated from the temperature and the given reduction rate. It is shown that this method could be well applied to assess the safety of concrete column or beam of the burned building.

• The Bulletin of The Korean Astronomical Society
• /
• v.44 no.1
• /
• pp.71.3-71.3
• /
• 2019

For slitless spectroscopy, we have installed the Volume Phase Holographic (VPH) gratings in the filter wheel of the SQUEAN on the 2.1m telescope at McDonald Observatory in Texas, United States. This system can effectively take spectra and monitor the variabilities of many sources, such as quasi-stellar objects, supernovae, and active galactic nuclei. On the single image frame, there are many spectra of the point sources. Therefore, a target extraction needs to trace along the tilted dispersion and to minimize the confusions by other sources. We present a real-time reduction software that has the functions with spectra extraction and wavelength calibration.