• Journal of information and communication convergence engineering
• /
• v.15 no.1
• /
• pp.62-71
• /
• 2017

This paper presents a low-power voltage converter based on a reconfigurable capacitor array. Its energy recycling capacitor array stores the energy during a charge stage and supplies the voltage during an energy recycle stage even after the power source is disconnected. The converter reconfigures the capacitor array step-wise to boost the lost voltage level during the energy recycle stage. Its energy saving is particularly effective when most of the energy remaining in the charge capacitors is wasted by the leakage current during a longer sleep period. Simulations have been conducted using a voltage source of 500 mV to supply a $V_{DD}$ of around 800 mV to a load circuit consisting of four 32-bit adders in a 65-nm CMOS process. Results demonstrate energy recycling efficiency of 85.86% and overall energy saving of 40.14% compared to a conventional converter, when the load circuit is shortly active followed by a long sleep period.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.58 no.12
• /
• pp.2410-2415
• /
• 2009

Studying for environmental friendly and efficient energy source is now actively under way on because problems like environmental pollution and exhaust of natural resources are in issue. Fuel Cell which is an alternative energy source has low voltage and high current characteristic, therefore boost up voltage converter and DC-AC converter is required to use as a common power source. In this paper, DC-DC converter which has high efficient and high power density is proposed and verified by experimental result.

• Journal of Power Electronics
• /
• v.14 no.3
• /
• pp.458-467
• /
• 2014

In this paper, a single-phase current-source bidirectional converter topology for V2G applications is proposed. The proposed converter consists of a single-phase current-source rectifier (SCSR) and an auxiliary switching network (ASN). It offers bidirectional power flow between the battery and the grid in the buck or boost mode and expands the output voltage range, so that it can be compatible with different voltage levels. The topology structure and operating principles of the proposed converter are analyzed in detail. An indirect control algorithm is used to realize the charging and discharging of the battery. Finally, the semiconductor losses and system efficiency are analyzed. Simulation and experimental results demonstrate the validity and effectiveness of the proposed topology.

• Journal of Electrical Engineering and Technology
• /
• v.10 no.6
• /
• pp.2297-2306
• /
• 2015

This paper presents the development of a system with a reverse matrix converter (RMC) for permanent magnet synchronous motor (PMSM) drive and its effective control method. The voltage transfer ratio of the general matrix converter is restricted to a maximum value of 0.866, which is not suitable for applications whose source voltages are lower than the load voltages. The proposed RMC topology can step up the voltage without any additional components in the conventional circuit. Its control method is different from traditional matrix converter’s one, thus this paper proposes control schemes of RMC by means of controlling both the generator and motor side currents with properly designed control loop. The converter can have sinusoidal input/output current waveforms in steady state condition as well as a boosted voltage. In this paper, a hardware system with an RMC for a PMSM drive system is described. The performance of the system was investigated through experiments

• Proceedings of the KIEE Conference
• /
• 1999.07f
• /
• pp.2656-2658
• /
• 1999

This paper presents a control scheme for a three-phase PWM converter system without any voltage sensors. Two input currents and one load current are measured. In a general PWM converter system, the required AC input and DC output voltage values in order to control the converter are estimated using the differential equations of the converter from the measured input currents and load current values in the switch modes of the converter circuit. The PI controller is used as DC voltage controller and sinusoidal tracking controller which tracks directly AC input current is used as input current controller. The Proposed method is verified by simulations. This paper describes the estimation method and configuration of the controller, and discusses steady state and transient performances of the converter

• The Transactions of the Korean Institute of Power Electronics
• /
• v.15 no.4
• /
• pp.327-334
• /
• 2010

This paper deals with a single-phase dynamic voltage restorer(DVR) with a quasi Z-source topology. The proposed system based on a single-phase quasi Z-source PWM ac-ac converter which have features such as the input voltage and output voltage are sharing ground, and input current operates in continuous current mode(CCM). For the detection of voltage sag-swell, peak voltage detection method is applied. Also, the circuit principles of the proposed system are described. During the 60% severe voltage sag and 30% voltage swell, the proposed system controls the adding or missing voltage and maintains the rated voltage of sinusoidal waveform at the terminals of the critical loads. Finally, PSIM simulation and experimental results are presented to verify the proposed concept and theoretical analysis.

• Journal of international Conference on Electrical Machines and Systems
• /
• v.3 no.3
• /
• pp.298-304
• /
• 2014

In this paper, a novel topology for cascade multilevel converter is introduced, which has many levels with fewer number of power electronic components. Less number of the switches leads to the reduction of size, losses, simple control strategy and high efficiency. For proposed multilevel converter, a new algorithm for determination of dc voltage source values has been recommended. The performance and operation of the proposed multilevel converter has been evaluated with the simulation results of a cascade 25-level converter.

• Proceedings of the KIPE Conference
• /
• 2011.07a
• /
• pp.444-446
• /
• 2011

A bidirectional dual active converter with the power factor control capability is proposed as a battery charger. The source side half-bridge acts as a PWM converter that maintains the unity power factor. The battery side half-bridge converter acts as a dual active bridge (DAB) together shares the same DC link voltage with PWM converter. The imbalance voltage phenomenon is eliminated by employing asymmetric duty cycle technique. Simulation results are included to verify theoretical analysis.

• Journal of Power Electronics
• /
• v.17 no.2
• /
• pp.422-431
• /
• 2017

The equivalent circuit of a three-leg, four-wire voltage source converter (VSC) is derived using switching functions. Simulations and experiments are conducted (i) to investigate the effects of the zero sequence on VSCs when a three-phase imbalance exists and (ii) to use the consistency of simulations and laboratory experiments to validate the equivalent circuit. The impact of a three-phase imbalance on the VSC has yet to be fully investigated because of the lack of an equivalent circuit to show rigorously how the zero sequence currents flow through the VSC.

• Proceedings of the KIPE Conference
• /
• 2010.07a
• /
• pp.412-413
• /
• 2010

Voltage Source Converter(VSC)는 입력전류와 전압을 동상의 정현파로 제어할 수 있고, 전압을 승압하여 일정한 DC전압을 만들 수 있으며, 양방향 제어가 가능하다. 본 논문은 3상 VSC를 동기회전좌표계로 변환하여 등가회로로 모델링하고, VSC의 제어기와 소신호 등가모델을 제시한다. 시뮬레이션을 통해 회로해석과 소신호 등가모델의 타당성을 검증하였고, 실험결과를 통하여 제어기를 설계의 타당성을 증명하였다.