• 융합신호처리학회논문지
• /
• 제3권2호
• /
• pp.83-88
• /
• 2002

본 논문에서는 온도보상과 POS 접속이 가능한 LPG 충전제어시스템을 구현하였다. 이 시스템은 16-bit 80C196 마이크로프로세서와, RAM, ROM, 비디오 driver, 프로그램주변소자 등으로 구성된다. 가스 유량계로부터의 부호화 유량신호와 장치교정 값, 온도센서로부터의 변환된 전압 값을 근거로 정확한 가스 충전량을 계산하고 솔레노이드 밸브를 on/off 함으로 충전량을 제어한다. 온도보상은 LP 가스 온도의 10-bit 아날로그-디지털변환에 의하여 0.5$^{\circ}C$의 분해능으로 이루어지며 온도보상의 범위는 영하 30도에서 영상 70도까지 가능하다.

• 대한전기학회논문지
• /
• 제38권7호
• /
• pp.539-548
• /
• 1989

본 논문에서는 싸이리스터 부하에서 발생하는 무효전력과 고조파를 보상하기 위한 순시무효전력 보상장치에 관하여 기술하였다. 저자는 기본파 위상 지연과 고조파 전류외형에 기인하는 순시무효전력을 새로이 정의하고 순시전력흐름의 관점에서 그 물리적 의미를 고찰하였다. 순시전압 및 순시전류의 궤환에 의해 순시무효전력을 계산하고, 이를 부하와 병렬로 연결된 전류제어형 PWM컨버터에 의해 보상하였다. PWM컨버터는 전류오차 백터제어방식에 의한 전류제어 PWM 기법을 사용함으로써 우수한 전류제어특성을 실현할 수 있었다. 시뮬레이션과 실험을 통하여 정상상태 및 과도상태에서의 탁월한 보상특성이 입증되었다.

• 한국전자파학회논문지
• /
• 제13권10호
• /
• pp.982-988
• /
• 2002

본 논문은 통신방송위성 중계기용 Ku-대역 채널증폭기 시험모델의 설계와 제작과정을 요약하였다. 채널증폭기의 구조는 고정이득제어 모드에서는 전압제어형 감쇄기를 이용한 아날로그 이득 조절 방식을 사용하였으며 자동레벨조절 모드에서는 루프제어방식을 이용한 출력레벨 제한회로를 사용하였다. 설계된 채널증폭기는 전압제어형 PEN-다이오드 감쇄기와 온도보상회로 등의 최신 기술 등을 이용하였다. 측정된 특성은 설계치와 동일하게 28 dB의 이득조절 및 16 dB의 자동이득조절 범위를 갖는 것을 확인하였다. 설계된 시험모델은 인증을 거치면 Ku-대역 통신방송 위성중계기용 채널증폭기로 사용되어질 수 있다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 춘계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.285-287
• /
• 2001

To obtain a high performance in a vector controlled induction machine, it is essential to know the instantaneous position of the rotor flux which depends on the rotor time constant. But the rotor time constant mainly varies due to the temperature rise in the motor winding, so real time compensating algorithm is necessary. This paper proposes that it uses short duration pulses added to the constant flux command current and then resultant torque command current produced by speed controller is utilized for the rotor resistance estimation. This method has advantages with a low computational requirement and does not require voltage sensors. The proposed method is proved by simulations.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 제37회 하계학술대회 논문집 B
• /
• pp.1008-1009
• /
• 2006

There is an application which uses smoothing reacter connecting each of the phases in order to make the system smaller comparison with an application using the insulating transformer in the utility interactive photovoltaic generation system using the PWM converter. In this case, there might be the occurence of the unbalance of output voltage, by the difference of smoothing reactor, connected on each of the lines. Therefore this study proposes that the method which maintains the balance and compensates the unblance which occured by the different volume of the smoothing reactor connected on each of the lines.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2006년도 하계종합학술대회
• /
• pp.499-500
• /
• 2006

This paper presents a fast switching CMOS frequency synthesizer with a new coarse tuning method for PHS applications. To achieve the fast lock-time and the low phase noise performance, an efficient bandwidth control scheme is proposed. Charge pump up/down current mismatches are compensated with the current mismatch compensation block. Also, the proposed coarse tuning method selects the optimal tuning capacitances of the LC-VCO to optimize the phase noise and the lock-time. The measured lock-time is about $20{\mu}s$. This chip is fabricated with $0.25{\mu}m$ CMOS technology, and the die area is $0.7mm{\times}2.1mm$. The power consumption is 54mW at 2.7V supply voltage.

• 전기학회논문지
• /
• 제57권12호
• /
• pp.2276-2280
• /
• 2008

In this paper, we present thermal dependancy of LED package element by changing temperature of MCPCB for design high efficiency LED lamp, and confirmed influence of LED chip against temperature with analysis of thermal resistance and thermal capacitance. As increasing temperature, WPOs were decreased from 25 to 22.5 [%] and optical power were also decreased. that is decreased reason of optical power that forward voltage was declined by decrease of energy bandgap. Therefore optical power by temperature of MCPCB should consider to design lamp for street light and security light. Moreover, compensation from declined optical efficiency is demanded when LED package is composed. Also, thermal resistances from chip to metal PCB were decreased from 12.18 to 10.8[$^{\circ}C/W$] by changing temperature. Among the thermal resistances, the thermal resistance form chip to die attachment was decreased from 2.87 to 2.5[$^{\circ}C/W$] and was decreased 0.72[$^{\circ}C/W$] in Heat Slug by chaning temperature. Therefore, because of thermal resistance gap in chip and heat slug, reliability and endurance of high power LED affect by increasing non-radiative recombination in chip from heat.

• 전기학회논문지P
• /
• 제66권2호
• /
• pp.82-87
• /
• 2017

This paper presents performance improvement of CO gas sensor signal conditioner for early fire warning system. The warning system is based on the CO sensor and its advanced signal conditioning modules network that employ electochemical gas sensor. The electochemical has advantage of having a linear output and operating with a low consumption and fast response. This electrochemical gas sensor contains a gas membrane and three electrodes(working, counter, reference electrode) in contact with an electrolyte. To use a three-electrode sensor, a voltage has to be applied between the working and the reference electrode according to the specification of the sensor. In this paper, we designed these requirements that should be considered in temperature compensation algorithm and electrode measurement of CO sensor modules by using advanced signal conditioning method included 3-electrode. Simulation and experimental results show that signal conditioner of CO sensor module using 3-electrode have a advantage linearity, sensitivity and stability, fast response etc..

• Journal of Electrical Engineering and Technology
• /
• 제13권2호
• /
• pp.608-619
• /
• 2018

As distributed generation (DG) is connected to grid, there is new node-type occurring in distribution network. An efficient algorithm is proposed in this paper to calculate power flow for weakly meshed distribution network with DGs in different load models. The algorithm respectively establishes mathematical models focusing on the wind power, photovoltaic cell, fuel cell, and gas turbine, wherein the different DGs are respectively equivalent to PQ, PI, PQ (V) and PV node-type. When dealing with PV node, the algorithm adopts reactive power compensation device to correct power, and the reactive power allocation principle is proposed to determine reactive power initial value to improve convergence of the algorithm. In addition, when dealing with the weakly meshed network, the proposed algorithm, which builds path matrix based on loop-analysis and establishes incident matrix of node voltage and injection current, possesses good convergence and strong ability to process the loops. The simulation results in IEEE33 and PG&G69 node distribution networks show that with increase of the number of loops, the algorithm's iteration times will decrease, and its convergence performance is stronger. Clearly, it can be effectively used to solve the problem of power flow calculation for weakly meshed distribution network containing different DGs.

• Journal of Power Electronics
• /
• 제9권4호
• /
• pp.654-666
• /
• 2009

Direct torque control (DTC) of induction machines (IM) is a well-known strategy of these drives control which has a fast dynamic and a good tracking response. In this paper a nonlinear DTC of speed sensorless IM drives is presented which is based on input-output feedback linearization control theory. The IM model includes iron losses using a speed dependent shunt resistance which is determined through some effective experiments. A stator flux vector is estimated through a simple integrator based on stator voltage equations in the stationary frame. A novel method is introduced for DC offset compensation which is a major problem of AC machines, especially at low speeds. Rotor speed is also determined using a rotor flux sliding-mode (SM) observer which is capable of rotor flux space vector and rotor speed simultaneous estimation. In addition, stator and rotor resistances are estimated using a simple but effective recursive least squares (RLS) method combined with the so-called SM observer. The proposed control idea is experimentally implemented in real time using a FPGA board synchronized with a personal computer (PC). Simulation and experimental results are presented to show the capability and validity of the proposed control method.