• 한국소음진동공학회논문집
• /
• 제25권8호
• /
• pp.539-545
• /
• 2015

Intense acoustic load is generated when a launch vehicle lifts off, causing the damaging vibrations at the launch vehicle or satellite within the fairing. This paper is concerned with the prediction of lift-off acoustic loads for a launch vehicle. As a test example, the lift-off acoustic load on the Korean launch vehicle, NARO, is predicted by the existing calculation tool, the modified Eldred's second method. Although the acoustic sources, assumed as point sources, are to be located along the center line of the exhaust plume when using the Eldred's prediction method, the exact location of the deflected center line of exhaust gas flow is not usually known. To search for the most appropriate source positions, six models of source line distribution are suggested and the acoustic load prediction results from these models are compared with the actual measurements. It is found that the predicted sound pressure spectrum of the Naro is the most similar to the measured data when the centerline of the turbulent kinetic energy contour is used as the source line.

• 한국소음진동공학회논문집
• /
• 제17권6호
• /
• pp.477-483
• /
• 2007

Major noise source in high speed rotating optical disk drives (CD and DVD-ROM) arises due to the high-speed airflow produced from the upper and lower surfaces on the rotating disk. The present paper deals with the experimental approach how to identify the noise source based on the fundamental principles of aeroacoustics and to propose a reduction method of the noise source. The CD-ROM device is composed of disk, window tray, motors at the bottom place and electronic circuit plate also located below the window plate. The window is cut in the tray to read the disk information using the optical device located below the tray and moving linearly from the center of the disk through the end of the disk. All components are possible noise generators. Experimental studies were carried out in the anechoic room with various design modifications, such as tray geometry, window size and hole location on tray, to identify the major aerodynamic noise source and significant reductions of the aerodynamic noise were obtained.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2008년도 추계학술대회논문집
• /
• pp.641-645
• /
• 2008

In this paper, vibration sources of the BLOC motor are identified and the motor vibrations are reduced by structural modification. For vibration characteristic identification, vibration signals measured by an accelerometer when the BLOC motor is moving. These signals are presented in a waterfall plot in order to find the dependency of frequency components on the motor speed. It is found that main vibration source is BLOC motor test rig. From finite element analyses and some experiments, it is also found that resonances occur because the natural frequencies of the test rig exist in usual driving speed rang. To shift the natural frequencies outside the driving rang, the test rig is modified increase stiffness. It is verified that considerable amount of vibration are reduced by the structural modification.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2008년도 추계학술대회논문집
• /
• pp.49-53
• /
• 2008

This study deals a way to reduce the transformer noises. The first step is to identify the source of the transformer noises. The second step is obtaining the vibration characteristics of transformer; its natural frequencies and mode shapes. Based on these information, an method to reduce the vibration of transformer can be found. The cause of transformer noises is mainly due to the magnetostrictive vibration of a core which is made of ferromagnetic substances. It is well known that the magnetostrictive vibration of a core is unavoidable, and a way to reduce the transformer noise by structural design is needed. It requires understanding the vibration characteristics. The natural frequencies and the mode shapes of transformer are analyzed by performing the modal testing.

• 한국소음진동공학회논문집
• /
• 제24권2호
• /
• pp.102-107
• /
• 2014

The engine excitation forces are considered as major vibration source for the forklift truck, especially in small class. Even though the current engine mounting system designs are acceptable for vibration isolation, the performance of the engine mounting system is still required for the tendency of light weight, higher power and driver's higher vibration requirement. In this paper vibration reduction technique of forklift engine which is supported on rubber mounts is presented. Based on the dynamic model of resilient engine mounting system, design evaluation program is established. The design optimization technique and evaluation method of system properties are discussed. Effects of optimal design are validated through comparison with test results.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2006년도 추계학술대회논문집
• /
• pp.797-800
• /
• 2006

The power flow analysis(PFA) can be effectively used to predict structural vibration in medium-to-high frequency ranges. In this paper, vibration experiment has been performed to observe the analytical characteristics of the power flow analysis of the vibration of a plate. In the experiment, the loss factor of the plate and the input mobility at a source point have been measured. The data for the loss factor has been used as the input data to predict the vibration of the plate with PFA. The frequency response functions have been measured over the surface of the plate. The comparison between the experimental results and the predicted results for the frequency responsefunctionshasbeenperformed.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 추계학술대회논문집
• /
• pp.428-433
• /
• 2002

There have been many studies to visualize the vibration and noise of rotary compressor. Most of these studies assumed that the signal is stationary and the time-averaged signal is used for visualization. However, the noise and vibration signals generated during one cycle of crank shaft vary continuously. In this paper, the noise and vibration of rotary compressor which vary continuously are visualized by short time fourier transform method. The location of source and the transfer path of vibration and noise at arbitrary frequencies, which can not be visualized by averaged signal, can be visualized clearly.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2000년도 춘계학술대회논문집
• /
• pp.157-164
• /
• 2000

A mechanical equipment room with various equipments may be the largest source of noise and vibration. Without sufficient consideration for noise and vibration control in the phase of designing, it causes some problems after completing construction or enormous cost necessary to correct the problems. Therefore, it is essential to consider the method of noise and vibration control, but the systematic guideline of noise and vibration is not provided yet. This study aims to investigate the actual condition of noise and vibration generated from mechanical equipments in apartment buildings, for providing the guideline of its control.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 춘계학술대회논문집
• /
• pp.1142-1147
• /
• 2002

For the evaluation of the DC motor noise and vibration, usually it is rely on human feeling because some kinds of noise are not definitely represented by measurement Instrument such as sound meter. But when we consider time signal of the noise and vibration. It is possible to represent them. And in this paper. it is suggested to study output current shape of the motor because it Is the source to make speed and torque variation of the motor. If the current shape is not stable. it makes operating state of the motor unstable and produces noise and vibration. By analyzing signal at time and frequency of noise and vibration and current shape. it is possible to automation of the noise and vibration measurement in the Production line.

• 한국안전학회지
• /
• 제20권1호
• /
• pp.13-17
• /
• 2005

This paper presents an information system of noise and vibration caused by people as a major source of the environmental problem in residential areas with which people are dissatisfied. Therefore, it is important to monitor the influence of noise and vibration in residential areas. Generally, Geographical Information Systems (GIS) play an important role in noise and vibration mapping. The purpose of this paper is to investigate noise and vibration effects in an urban area and develop a new information network in GIS. Noise and vibration measurements were carried out at a road randomly chosen near INJE University. The obtained values are graphically represented with GIS. Therefore, it is possible to predict noise and vibration in GIS when establishing effective urban plans.