• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.06a
• /
• pp.1883-1888
• /
• 2000

In this paper a computer aided analysis method is proposed for durability assessment in the early design stages using dynamic analysis, stress analysis and fatigue life prediction method. From dynamic analysis of a vehicle suspension system, dynamic load time histories of a suspension component are calculated. From the dynamic load time histories and the stress of the suspension component, a dynamic stress time history at the critical location is produced using the superposition principle. Using linear damage law and cycle counting method, fatigue life cycle is calculated. The predicted fatigue life cycle is verified by experimental durability tests.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.06a
• /
• pp.862-867
• /
• 2000

The auxiliary engine exhaust noise in ships are directly transmitted to bridge wing with the only distance attenuation. It is not so practical that no special treatment can be applied between exhaust pipe and bridge wing in order to reduce the transmission of the exhaust noise. In general, a silencer is fitted to reduce the exhaust noise and also noise of bridge wing. The silencer should be properly designed under the consideration of the frequency component of the exhaust noise and the required insertion loss. In this paper, the frequency component of exhaust noise of various engines are compared and a design and a design and installation of silencer to reduce low frequency is introduced.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.11a
• /
• pp.377-382
• /
• 2003

In our previous study, we have developed sound quality index for steady rumbling sound of passenger car. In this paper, we will study sound quality index for transient rumbling noise. The subjective evaluation of rumbling sound can be indicated to objective parameters by sound metrics of psychoacoustics and principal rumble component. And artificial neural network can be estimated complexity and nonlinear characteristics of relation between subjective evaluation and sound metrics. We applied to sound metrics and artificial neural network to development of sound quality index for transient rumbling sound of passenger car.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.05a
• /
• pp.81-85
• /
• 2006

The motion of a system composed of a plate, constant springs and varying dampers is considered when the system is subject to harmonic force. Letting the frequencies of harmonic force and damper variation ${\Large f}_1\;and\;{\Large f}_2$, respectively, the displacement at the center of the plate has the strongest component at frequency ${\Large f}_1$. The angular displacement of the plate has strong components at ${\Large f}_1-{\Large f}_2$, and the natural frequency of the rotational mode of the system. If these two frequencies coincide, the plate oscillates with almost single frequency and a large amplitude. These results can be applied to development of a moment shatter with low frequencies.

• Journal of KSNVE
• /
• v.2 no.2
• /
• pp.125-134
• /
• 1992

In this study, ti identify the dynamic characteristics of automobile steering system which consists of many components and joints, each component combined structure was analyzed using commercial structural package, ANSYS. And, the finite element method for each component and modeling method of several joints universal joint, bolt joint, bearing, etc. were studied. On the other hand, the experimental modal analysis was performed to compare with the results of the finite element analysis and joint modeling. The result shows very close agreement between two analysis. Also, it was found that the steeing column used in this experiment does not effect the low frequency mode of entire system. In addition, we found that constraint equations need to be considered in modeling universal joint. Since the stiffness effect of Urethane around wheel could be ignored, it can be modeled only with mass effect. In the end, it was found that dynamic characteristics of the entire steerintg system depends mainly upon the wheel characteristics.

• Proceedings of the KIEE Conference
• /
• 2002.07d
• /
• pp.2252-2254
• /
• 2002

The Reactor internal structures which consist of many complex components are subjected to flow-induced vibration due to high temperature and pressure in Reactor coolant system. The above flow-induced vibration causes degradation of structural integrity of the Reactor and may result in loosing mechanical binding component which might impact other equipment and component or cause flow blockage. It is important to analyze reactor noise signal for the early detection of potential problem or failure in order to diagnosis reactor integrity in the point of view of safety and plant economics. Detailed composition of diagnostic system reactor internal structures using neutron noise(RIDS).

• Proceedings of the KIEE Conference
• /
• 2001.07d
• /
• pp.2166-2168
• /
• 2001

Reactor Noise is defined as the fluctuations of measured instrumentation signals during full-power operation of reactor which have informations on reactor system dynamics such as neutron kinetics. The Reactor internal structures which consist of many complex components are subjected to flow-induced vibration due to high temperature and pressure in reactor coolant system. The above flow-induced vibration causes degradation of structural integrity of the reactor and may result in loosing mechanical binding component which might impact other equipment and component or cause flow blockage. It is important to analyze reactor noise signal for the early detection of potential problem or failure in order to diagnosis reactor integrity in the point of view of safety and plant economics. Detailed design of hardware diagnostic system reactor internal structures using neutron noise(RIDS).

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1996.10a
• /
• pp.118-123
• /
• 1996

The purpose of this study is to develop acoustic substructure synthesis method that can be applied to acoustic modal analysis of complex acoustic systems. Acoustic modal analysis method to be introduced here is a method that analyze acoustic natural mode shape of the complex acoustic system by the principle of CMS(component mode synthesis method). This paper describes the acoustic modal analysis of the acoustic finite element model of simple expansion pipe by acoustic substructure synthesis method. The results of acoustic modal analysis analyzed by Acoustic substructure synthesis method and the results, by FEM(finite element method) shows good agreement.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1997.10a
• /
• pp.263-270
• /
• 1997

For a cylinder in a uniform flow stream, sound is generated by the fluctuating pressure on the cylinder surface due to the vortex shedding behind the cylinder. It is known that the major parameters to predict the sound pressure are the characteristic length of the flow along the cylinder axis and the fluctuating lift coefficient. These parameters strongly depend on the Reynolds number and the yaw angle of the cylinder to the free stream. In this experimental study the effects of yaw on the flow parameters, and consequently on the generated sound are investigated. The surface pressure and the radiated sound are measured simultaneously for different yaw angles and showed that the reduced normal velocity component to the cylinder axis reduces the unsteady lift fluctuation which results in lowered sound press-are level, However, experimental result shows that "the cosine law" which uses the normal velocity component as a characteristic velocity for noise Generation from a yawed cylinder needs to be carefully reviewed. reviewed.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.11a
• /
• pp.852-855
• /
• 2005

Structural Dynamic Modification(SDM) is a technique to improve structure's dynamic characteristics by adding and removing substructures or changing material properties and shape of structures. This paper describes SDM techniques applied to a large structure with too many DOFs. The goal of this SDM technique is to modify a targe structure efficiently for its natural frequencies to avoid excitation frequencies. In this case, models reduced by Component Mode Synthesis(CMS) method that is a coupling technique are used to analyze a large structure efficiently. This paper considers a helicopter deck model with 55,000 DOFs as an application.