• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2012년도 춘계학술대회 논문집
• /
• pp.169-170
• /
• 2012

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2008년도 춘계학술대회 논문집
• /
• pp.321-322
• /
• 2008

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2009년도 추계학술대회 논문집
• /
• pp.197-198
• /
• 2009

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2007년도 춘계학술대회 논문집
• /
• pp.13-14
• /
• 2007

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2011년도 춘계학술대회 논문집
• /
• pp.37-38
• /
• 2011

• 한국생산제조학회지
• /
• 제9권3호
• /
• pp.150-159
• /
• 2000

In-process diagnosis of the cutting state is essential for the automation of manufacturing systems. Especially when the cutting process becomes unstable it induces self-exited vibrations a frequent case of poor tool life rough surface finish damage to the workpiece and the machine tool itself and excessive down time. To ensure that the cutting process main-tains stable it is highly desirable to have the capability of real-time. To ensure that the cutting process main-tains stable it is highly desirable to have the capability of real-time monitoring and controlling chatter. This paper describes the detection method of chatter vibration using cutting force in turning process. In order to detect a chatter vibra-tion the dynamic fluctuation of radial force is analyzed since this components is sensitive to the chatter. The envelope sig-nal of radial force has been calculated by the use of FIR Hilbert transformer and it was useful to classify the chatter signal from the dynamically unstable circumstances. It was found that the mode and the mode width were closely correlated with the chatter amplitude was well. Finally back propagation(BP) neural network have been applied to the pattern recognition for the classification of chatter signal in various cutting conditions. The validity of this systed was confirmed by the experiments under the various cutting conditions.

• 한국기계가공학회지
• /
• 제4권1호
• /
• pp.37-42
• /
• 2005

The localization of manufacturing technique development is actualizing for low cost with supplies of display devices. We need more high cutting technique because consumers want flat glasses of various sizes. Recently, most general two methods are normal wheel cutting and laser cutting, but both of them have some faults. First, the wheel cutting has cracks and sharp edges of sections. Second, it is easy for laser cutting to cut curved lines. however, it has thermal damage and low traverse speed. I suggest a new cutting method by high-wave frequency vibration wheel cutting(HFVC), which is good for quality improvement. Vertical cracks and crack depth is observed, after HFVC. When the average of the crack depth is $30{\mu}m$ and the average of the wallner liner depth is $200{\mu}m$, it has the most high quality of the sections in this experiment. As a result, when we consider between the normal wheel cutting method and the HFVC method, the latter has low cracks and good quality.

• 한국정밀공학회지
• /
• 제28권6호
• /
• pp.709-715
• /
• 2011

Chattering in cutting operations are usually a cumbersome part of the manufacturing process in mechanical. Particular, machining performance such as that of the boring process is limited by cutting condition at the movable components. Among various sources of chatter vibration, detrimental point in cutting condition is found a mechanical condition on overhang. It limits cutting speed, depth, surface roughness and tool wear failure as result because the all properties are varying with the metal removal process. In this case, we have to observe the resonance frequencies of a boring bar for continuous cutting. In the established research, boring bar vibration of cutting system has been measured with the aid of accelerometer. However, the inherent parameters of internal turning operations are severely limit for the real time monitoring on accelerometers. At this point, this paper is proposed other method for real time monitoring during continuous cutting with optical fiber at the inside of boring bar. This method has been used a plastic fiber in the special jig on boring bar by based on experimental modal analysis. In this study, improvement of monitoring system on continuous internal cutting was attempted using optical fiber sensor of inside type because usually chattering is investigated experimentally measuring the variation in chip thickness. It is demonstrated that the optical fiber sensor is possibility to measure of chattering with real time in boring process.

• 한국기계가공학회지
• /
• 제13권1호
• /
• pp.59-65
• /
• 2014

To obtain an elliptical trajectory at the cutting edge during elliptical vibration cutting, sinusoidal voltage excitations of two piezoelectric actuators have commonly been used. In this study, PWM excitation, which is relatively simple to generate, was employed and its characteristics were investigated. In experimental and analytical analyses, we found that for PWM excitation, the integer-multiple frequencies of the excitation voltage distorted the shape of the elliptical trajectory, whereas at a duty ratio(DR) of 50%, the distortion of the elliptical trajectory was minimized due to disappearance of the first overtone. When the magnitude of the maximum excitation voltage was maintained at the same level for both PWM and sinusoidal excitation, PWM (DR=50%) excitation produced a greater vibration amplitude than sinusoidal excitation but resulted in more rapid saturation of a high-frequency power amplifier.

• 한국생산제조학회지
• /
• 제20권3호
• /
• pp.268-273
• /
• 2011

In light guide panels, the PMMA sheet that is used in liquid crystal displays plays an important role in scattering the incident light and requires very fine machining as the sheet is directly related to the optical characteristics of the panels. High speed end milling(HSE) and high speed shaping(HSS) processes that are widely adopted and applied to the precise machining of light incident plane through vibration-assisted HSS for increasing the optical quality by minimizing the above-mentioned problems. The cutting tool and the tool post presented in this paper are designed by the authors to increase the magnitude of the cutting stroke by adopting the resonant frequency without weakening the stiffness and to reduce vibrations during even high speed feeding. The dynamic haracteristics of thecutting tool and the tool post are evaluated through simulation and experiment as well. The results reveal very appropriate dynamic characteristics for vibration-assisted HSS.