• Journal of Biosystems Engineering
• /
• 제26권4호
• /
• pp.331-336
• /
• 2001

This study was to develop a kerosene flame weeder. An air compressor was driven though the PTO of a tractor to provide necessary air for fuel combustion and proper pressure to supply fuel from fuel tank to the nozzle. It was found that the flame was extinguished very easily by wind and vibration of the tractor. This trouble could be solved by attaching a burner cap, which is a modified venturi tube, at the end of the nozzle. The constructed flame weeder was tested for the weeding capability in the prepared field. Weed extinction rate and weight decrease rate were analysed. Measured maximum flame temperature was 1,121$\^{C}$ when the fuel consumption was 13.41 kg/h and fuel supply pressure was 88.2 kPa. The maximum temperature occurred at 20cm from the front end the burner, and it decreased to 46$\^{C}$ as the distance increased to 110cm. The flame length of up to 70cm, where the flame temperature was higher than 372$\^{C}$, would be used for weeding purpose. Weed extinction rate and weight decreasing rate increased as the fuel consumption increased. The flame weeder was evaluated to be a practical weeder through improvement as the weed extinction rate and weight decrease rate were analysed to be 75% and 85%, respectively when the fuel consumption was 116.87kg/ha.

• International Journal of Aeronautical and Space Sciences
• /
• 제6권1호
• /
• pp.17-26
• /
• 2005

An optical phase tracking technique for an extrinsic Fabry-Perot interferometer (EFPI) is proposed in order to overcome interferometric non-linearity. Basic idea is utilizing strain-rate information, which cannot be easily obtained from an EFPI sensor itself. The proposed phase tracking system consists of a patch-type EFPI sensor and a simple on-line phase tracking logic. The patch-type EFPI sensor comprises an EFPI and a piezoelectric patch. An EFPI sensor itself has non-linear behavior due to the interferometric characteristics, and a piezoelectric material has hysteresis. However, the composed patch-type EFPI sensor system overcomes the problems that can arise when they are used individually. The dynamic characteristics of the proposed phase tracking system were investigated, and then the patch-type EFPI sensor system was applied to the active suppression of flutter, dynamic aeroelastic instability, of a swept-back composite plate structure. The proposed system has effectively reduced the amplitude of the flutter mode, and increased flutter speed.

• 환경영향평가
• /
• 제20권2호
• /
• pp.123-131
• /
• 2011

The objective of this study is to prepare the effective management plan of environmental noise with a noise map, and the guideline on the management plan of environmental noise was suggested through the review of existing application examples. The management plan of environmental noise with a noise map includes the practical contents in the stages of subdivision of management areas, establishment of reduction measures, opinion collection, post investigation, and reformulation of management plan. First, the classification of management regions is performed considering the excess degree of noise standard and the facility type in the phase of subdivision of management areas. Second, the optimal management plan is established through the investigation of regional characteristics and various noise reduction measures in the phase of establishment of reduction measures, which includes the examination of noise reduction effects with a noise map and the budget planning with the costing of noise reduction measures. Third, the opinion survey with a local resident and a expert is carried out in order to prove the validity of the management plan in the phase of opinion collection, and the management plan is modified with gathered opinions. Fourth, the post examination plan with noise measurement is performed in order to verify the real effect of noise reduction measures according to the management plan in the phase of post investigation. Finally, the amendment of the management plan as well as the improvement of a noise map is carried out at a regular cycle in the phase of reformulation of management plan.

• 한국공간구조학회논문집
• /
• 제10권1호
• /
• pp.85-93
• /
• 2010

공간구조의 지붕을 지지하는 기둥상단부에 탄소성기구를 설치하여 설계 하중을 초과하는 지진동이 가해졌을 때 이 기구의 탄소성 이력거동을 통하여 지진에너지가 흡수되는 효과를 검토한다. 이 효과로 지붕트러스로 전달되는 지진에너지가 저감되는 것을 입증하고 이러한 원리를 공간구조물의 제진설계에 활용할 수 있음을 입증한다. 트러스 형식의 지붕구조에 설계하중 이상의 외력이 가해지는 경우에는 구성부재의 좌굴파괴로 인한 건물전체의 취성붕괴가 예상되기 때문에 이러한 상황에서 구조안전성을 확보하는 설계법이 요망되며, 이 논문은 트러스 지붕에 전달되는 지진에너지를 감소시키는 설계방법을 제안하고 있다.

• 한국지능시스템학회논문지
• /
• 제15권4호
• /
• pp.431-436
• /
• 2005

본 연구는 연속 회분식 반응기(SBR) 공정에서 시계열 데이터 마이닝을 이용하여 공정에 사용된 기기의 고장 진단 알고리즘 개발에 대한 내용을 보여주고 있다. 공정에서 비정상적인 반응을 유발하는 장비 관리에 대한 연구는 폭넓게 수행되고 있지 않으므로, 이러한 장비 진단은 소규모 하$\cdot$ 폐수처리장을 무인자동화로 통합관리에 유용하게 적용될 수 있다. 본 연구에서는 진동신호를 이용하여 무인자동화를 위해 선행되어야 하는 공정기기의 공장진단에 관한 알고리즘을 개발하였다.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2008년도 춘계학술대회 논문집
• /
• pp.1227-1232
• /
• 2008

High-speed train of push-pull type called as G7 train has been developed and chosen as the model of KTX-II which will be operated on Honam Line nexr year. However, the EMU-type high-speed train appeared to be the recent trend that foreign markets have shown. Also, in the near future, a great number of new train sets are needed to accommodate the increased passengers in our country. Thus, development of the high-speed EMU was decided, planned, and started. In the development, included were almost all fundamental key technologies such as noise and vibration reduction in a passenger cabin, running characteristics, aerodynamic analysis, crashworthiness evaluation, EMI/EMC analysis, design of the cooling system for the propulsion control system, enhanced performance of transformer and switching converters, synchronous traction motor with permanent magnets, new design of front nose and ergonomic interiors, application of advanced information technology(IT) and smart sensors and the cost reduction of construction of railway bridges, etc. Each key technologies are carried out as sub-project independently but under the supervision of a project. The project will develop the high advanced level of technologies and provide necessary know-why's and support the team in charge of the development of the high-speed EMU, Hyundai Rotem Co. Ltd. The high-speed EMU will be successfully developed with the support of the project.

• The Journal of the Acoustical Society of Korea
• /
• 제24권3E호
• /
• pp.87-89
• /
• 2005

The acoustical sources of intake and exhaust systems in fluid machines are often characterized by the source impedance and strength using linear frequency-domain modeling. In the case of the sources which are nonlinear and time-variant, however, the source parameters were sometimes incorrectly obtained. In this paper, the source model and direct measurement technique are modified in order to evaluate the effect due to nonlinear and periodically time-varying source character as well as the linear property of the reflectivity of in-duct fluid machine source. With a priori known kinematical information of the source, the types of nonlinear time-variant terms can be presumed by a simple physical model, in which there is practically no restriction on the form of the model. The concept of source impedance can be extendable by introducing the linear frequency response function for each nonlinear or time-variant input. Extending the conventional method and adapting the reverse MISO technique, it is possible to develop a direct method that can deal with the nonlinear time-variant source parameters. The proposed direct method has a novel feature that there is no restriction on the probability or spectral natures of the excited sound pressure data. The present method is verified by the simulated measurements for simplified fluid machines. It is thought that the proposed method would be useful in predicting the insertion loss or the radiated sound level from intake or exhaust systems.

• 반도체디스플레이기술학회지
• /
• 제16권1호
• /
• pp.91-96
• /
• 2017

One of the most critical aspects of the modern semiconductor industry is the quality of wafer surface, the roughness of which is mostly caused by the ingot slicing. And the grinding is supposed to be the main process to reduce the surface roughness. The vibrations of the disc surface grinder are the major problem to effectively achieve the required surface quality. In this study, the structure of a disc surface grinder was analyzed through the experiment and the computer simulation to investigate the dynamic characteristics of the machine, and further to alter the design for the improved stability. The result of the study shows that simple design alterations without alternating main body can effectively suppress the vibrations of the machine.

• 드라이브 ㆍ 컨트롤
• /
• 제11권4호
• /
• pp.46-52
• /
• 2014

This study suggests a small-sized screw decanter specialized for dredging sites. Generally, conventional screw decanters are composed of a cylinder and a cone. However, the suggested screw decanter simply has a cone based on a cone-type bowl structure. In this research, a commercial analysis tool is used to establish an optimal design for the bowl and the screw conveyor. Moreover, the base frame, where the main bearings that support the spindle of the bowl and the screw conveyor are installed, is optimally designed considering the weight of the rotating body and the deflection caused by the high centrifugal force. Furthermore, the natural frequency range of the spinning body, the bowl and the screw conveyor, is applied to this base frame; it is designed not to correspond to the resonance frequency range and achieves stability as a result. This study suggests an optimal design for the rotating body and the base frame of a screw decanter considering its vibration characteristics. Such a design will prevent overuse of materials and help to reduce the weight and volume-and the price-of a screw decanter.

• 대한안전경영과학회:학술대회논문집
• /
• 대한안전경영과학회 2005년도 춘계학술대회
• /
• pp.273-278
• /
• 2005

Prescribed according to the occupational safety and health low noise measurement method was changed to personal sampling in the method to measure an area noise. Such method had the limit which did not evaluated characteristic of sound of occurrence and the place of origin. This study was performed to establish an engineering remedy of the work-place noise. The subject was a vibration control process of the place of business in Pusan. A simulation program applied for an engineering improvement of the work-place noise. The results were as follows: 1. An noise occurrence level of the work-place before improvement was $88^{\sim}97dB(A)$, We applied an improvement method to be established and were expected to $80^{\sim}119dB(A)$. 2. The level of the noise-distribution to appear in the place of origin of the work-place before improvement was $90^{\sim}93dB(A)$ but, We executed the simulation after applied an engineering remedy and predicted $80^{\sim}85dB(A)$. A result of the simulation blue part was changed mostly into the dark blue color. The results suggest that simulation program establishes an engineering remedy and is useful to the case to apply.