• Journal of the Korean Chemical Society
• /
• v.46 no.5
• /
• pp.467-476
• /
• 2002

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• v.1
• /
• pp.465-469
• /
• 2006

In recent years there has been considerable interest in the construction of super high-rise buildings. From the prior art, various procedures and devices for surveys during and after the phase of erection of a high-rise building are known. High-rise buildings are subject to strong external tilt effects caused, for instance, by wind pressures, unilateral thermal effects by exposure to sunlight, and unilateral loads. Such effects are a particular challenge in the phase of construction of a high-rise building, in as much as the high-rise building under construction is also subject to tilt effects, and will at least temporarily lose its - as a rule exactly vertical - alignment. Yet construction should progress in such a way that the building is aligned as planned, and particularly so in the vertical, when returning into an un-tilted basic state.It is essential that a straight element be constructed that theoretically, even when moving around its design centre point due to varying loads, would have an exactly vertical alignment when all biasing conditions are neutralised. Because of differential raft settlement, differential concrete shortening, and construction tolerances, this ideal situation will rarely be achieved. This paper describes a procedure developed by the authors using GPS observations combined with a network of precision inclination sensor to provide reliable coordinated points at the top of the worldwide highest-rise building under construction in Dubai.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.461-462
• /
• 2006

A single-gap and single-gamma transflective liquid-crystal (LC) display using patterned vertical alignment (PVA) mode was designed. In the device, a vertical electric field drives a vertically aligned LC to tilt down to optimize polarization efficiency. Electrodes of transmissive and reflective area were patterned $22.5^{\circ}$ and $45^{\circ}$ with respect to the polarizer so that a tilt-down direction of the LC director was $22.5^{\circ}$ and $45^{\circ}$ in the reflective and transmissive regions, respectively. In the device, the cell gap was the same for both regions, and the gamma curve matched each other in both regions because tilt angle of LC director was the same according to the applied voltage. Moreover, the dark state was irrespective of the cell retardation value at normal direction, which was highly important in massive fabrications. The switching principle and electro-optic characteristics of the device are reported herein.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.11 no.9
• /
• pp.1724-1728
• /
• 2007

In this paper we propose a novel electrode structure for high transmittance in the Patterned Vertical Alignment (PVA) LC cell. We use the 'TechWiz LCD' for calculation of the director configuration and optical characteristics. We studied the area decreasing the transmittance through the electrode structure for wide viewing angle and proposed new electrode design to change LC director configuration in the area. We show the comparison of the calculated optical transmittance between the conventional PVA mode and the proposed PVA mode. From the results, we confirm that the optical transmittance of the proposed structure of the PVA cell becomes higher.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.39-40
• /
• 2009

The patterned vertical alignment (PVA) display showed good electro-optic properties such as wide viewing angle, fast response time, high Contrast Ratio. However, the device has patterned electrode on both top and bottom electrodes which requires high accuracy of assembling of top and bottom substrates in order to exhibit a high performance. So, they have disadvantage about low yield. In order to resolve these problem, in this paper, we studied about top substrate pattern free vertical alignment device associated with surface polymer stabilization using the UV curable monomer. This method shows simple progress, low cost and good electro-optic properties such as high transmittance and fast response time.

• Current Optics and Photonics
• /
• v.1 no.2
• /
• pp.157-162
• /
• 2017

In large liquid crystal displays, the image quality in an oblique viewing direction is a crucial issue. From this perspective, 8-domain polymer-stabilized vertical alignment (PS-VA) mode has been developed to suppress the color shift in oblique viewing directions, compared to that in 4-domain PS-VA mode. To realize the 8-domain PS-VA, the four domains in a pixel are each divided into two regions, such that applying different electric potentials result in different tilt angles in these two regions, while keeping four azimuthal directions in each domain. However, applying different voltages in a pixel causes drawbacks, such as requiring additional processes to construct a capacitor and a transistor, which will further reduce the aperture ratio. Here we propose a different approach to form the 8-domain, by controlling surface polar anchoring energy and the width of patterned electrodes in two regions of a pixel. As a result, the gamma-distortion index (GDI), measured at an azimuthal angle of $0^{\circ}$, is reduced by about 23% and 8%, compared to that of a conventional 4-domain at polar angles of $30^{\circ}$ and $60^{\circ}$ respectively.

• Journal of the Optical Society of Korea
• /
• v.20 no.6
• /
• pp.794-798
• /
• 2016

A polymer-stabilized vertical alignment (PS-VA) mode with fishbone-shaped pixel electrode structure is mainly used in large-sized liquid crystal displays (LCDs) owing to its advantages such as wide viewing angle, good transmittance and fast response time. One drawback of this mode is a main bone electrode, which crosses in the center of a pixel. It causes the transmittance to decrease badly because LCs cannot be reoriented in this region, and thus, it is particularly unfavorable in an ultra-high-definition LCD. Here, we propose an innovative structure with the main bone electrode relocated to the edge area in a pixel, and investigate how this reverse directed fishbone-shaped pixel electrode structure affects electro-optic characteristics. The proposed structure shows enhanced electro-optic performance, such as the higher transmittance and the faster response time than the conventional VA mode with fishbone-shaped pixel electrode structure.

• Journal of Korea Foundry Society
• /
• v.21 no.5
• /
• pp.290-295
• /
• 2001

We fabricated test samples containing various shape elements and surface roughness checking points for the jewelry cast master patterns by employing the 3D computer aided design (CAD), selective laser sintering (SLS) rapid prototype (RP) with the DuraForm powders. We varied the alignment angle from $0^{\circ}$ to $10^{\circ}$ at a given layer thickness of 0.08 and 0.1mm, respectively, in RP operation. Dimensions of the shape elements as well as values of surface roughness are characterized by an optical microscope and a contact-scanning profilometer. Surface roughness values of the top and vertical face increased as the alignment angle increased, while the other roughness values and shape elements variation were not depending on the alignment angle. The resolution of the shape realization was enhanced as the layer thickness became smaller. The minimum diameter of the hole, common in jewelry design, was 1.2 mm, and the shrinkage became 12% at the 1.6 mm-diameter hole, Our results implied that we face down the proposed design elements with $0^{\circ}$ alignment angle, and consider the shrinkage effect of each shape element in DuraForm RP jewelry modeling.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.17 no.3
• /
• pp.134-140
• /
• 2018

This paper describes the design and fabrication of an automatic alignment and loading system for workpieces. To move a workpiece to a chucking position of a machine tool using a gantry robot, an automatic aligning device is required to load the workpiece before machining and automatically align them. The automatic alignment system was conceptually designed, and the structural analysis was performed for the main parts such as the top plate, center support, front and back support, and support shaft. Based on the structural analysis results, the size of these structures was determined. The automatic alignment system was manufactured, and the vertical movement characteristics of the workpiece up-and-down movement device and the rotation characteristics of the workpiece rotation device were experimentally examined. The result has confirmed that they operate normally.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.36 no.11
• /
• pp.1079-1086
• /
• 2008

During transfer alignment navigation information transferred MINS(master inertial navigation system) to SINS(slave inertial navigation system) has a changed time delay. The changed time delay degrades the performance of transfer alignment. This paper proposes an adaptive filter that estimates covariance of a time delay in real-time using residual of measurements. The performance of the adaptive filter is compared with that of the EKF(extended Kalman filter) in case of transfer alignment for vertical launcher in the ship. The results show that proposed method is more effective than EKF in estimating attitude errors.