• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2002년도 학술대회지
• /
• pp.525-528
• /
• 2002

The objective of this study is to investigate characteristics of flow by the Rod shape and the choice of the turbulent intensity enhancement section. The Rod was setup vertically to the way of a nozzle exit flow and nozzle diameter is 17mm. Rod height is 5mm and its shapes are square, triangle, and circle. Characteristics of fluid such as velocity vector distribution, kinetic energy, turbulent intensity, and etc. were visualized, observed, and considered at 3 kinds of Re No. such as 2000, 3000, and 4000. The characteristics of flow field were investigated in each case of the distance rate from the nozzle exit to impinging plate(H/B=8, 10). The temperature of water is $20^{\circ}E$ and the measurement region divided by 3 sections(I, II, III). The nozzle diameter is 17mm. As the experimental result by PIV measurement, scale of the vector profile showed a tendency to an unbalance parabola distribution as increasing of the Re No. When the impinging plates such as square, triangle, and circle shape are installed respectively in front of the flow accelerated, rod shape of the highest velocity vector is circle shape and rod shape of the highest turbulent Intensity is square shape.

• 설비공학논문집
• /
• 제13권3호
• /
• pp.160-166
• /
• 2001

A numerical analysis has been performed for natural convection in an air conditioner duct system. The governing equations were solved a finite volume method using a SIMPLE algorithm. In the calculation mode of duct, the room temperature was preserved at $25.0^{\circ}C$ and duct wall temperature had a temperature of 15, 20.0, 22.5, 23.75, 26.25, 27.5 30 and $35^{\circ}C$. The results of velocity vectors and contours have been represented for various parameters. Based on the numerical data, the relationships between temperature difference and flow rate into room was represented. In the case of $T_\gamma>T_\omega$, the equation for temperature difference and flow rate was $Q=0.0285\triangleT^0.4005$, and in the case of $T_\gamma>T_\omega$, the equation was $Q=0.0099\triangleT^0.4752$. The duct system has an important relation to room temperature and duct wall temperature.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2002년도 학술대회지
• /
• pp.439-442
• /
• 2002

In this study, a turbulence simulation is carried out in a suction type wind tunnel using grids, where turbulent flows with various turbulence intensity are successfully produced by the change of grid size, arrangement of grids and settling position, respectively. Response tests of rectangular cylinder models with aspect ratio of 2 and 4 are carried out in smooth flow and generated turbulent flows. Additionally, two types of fairing are considered such as right triangle and regular triangle. The effects of wind velocity fluctuations and fairing are discussed on vortex-induced oscillation.

• 조명전기설비학회논문지
• /
• 제25권5호
• /
• pp.104-109
• /
• 2011

In this paper, after an acceleration typed ion wind generator which could format strong electric field in air was manufactured and installed, the effects of the electrode configuration and distance of acceleration type ion wind generator with triangle structure on the ion wind generation characteristics were investigated. As a result, the ion wind generator with curvature multipoint electrode could generate higher ion wind velocity and ion wind generation yield than others with multipoint electrode, curvature line electrode, line electrode structure. The ion wind generator with curvature multipoint electrode showed a peak ion wind velocity of 1.33[m/s] at 19.0[kV] and a ion wind generation yield of 0.12[m/Ws] at 15.0[kV].

• 한국자동차공학회논문집
• /
• 제24권1호
• /
• pp.74-81
• /
• 2016

The aim of this study was to find the initial design value of turbine blade for electrical type turbocompound system generating 10 kW. Turbocompound is one of the waste heat recovery system applying to internal combustion engine to recover exhaust gas energy that was about 30 % of total input energy. To design the turbine blade, 1-D mean line flow model was used. Exhaust gas temperature, pressure, flow rate and turbine rotating speed was fixed as primary boundary conditions. The velocity triangles was defined and used to determine the rotor inlet radius and width, the rotor outlet radius at shroud and radius at hub, the rotor flow angles and the number of blades.

• 대한기계학회논문집B
• /
• 제20권6호
• /
• pp.1931-1940
• /
• 1996

The effect of periodic passing wake on the film-coolant flow issuing normally from a flat plate was investigated experimentally. The passing wake was generated by rotating thin circular bars. Depending on the rotational direction the test plate could be simulated as a pressure surface or a suction surface of a gas turbine blade. The phase-averaged velocity components were measured using an X-type hot-wire probe. The Reynolds number based on the free-stream velocity and injection hole diameter was 23, 500 and the velocity ratio which is the ratio of film coolant velocity to free-stream velocity was 0.5. The velocity-triangle induced by the wake was similar to that induced by the one generated at the blade trailing edge. The vertical velocity component induced by the passing wake, which approaches to the suction surface and moves away from the pressure surface, played a dominant role in the variation of the flow field. The variation in the phase-averaged velocity on the pressure surface was greater than on the suction surface, but the turbulence kinetic energy variation on the suction surface appeared larger than on the pressure surface.

• Journal of Advanced Marine Engineering and Technology
• /
• 제28권1호
• /
• pp.152-161
• /
• 2004

The thermal load is a very important problem to be solved in many industrial systems including the electronic equipment. Impinging Jets have been known to provide a large heat transfer rates on surface for many years. The turbulence enhancement of fluid flow is requested for the efficiency elevation of heat transfer. A study on flow fields by rods attached to the wall surface as a promoter of turbulence enhancement has been carried out. The exact analysis on chracteristics of impinging jet field is requested to obtain the optimum design of the impinging jet system. By visualizing the flow field and processing the high digital image by computer PIV can afford exact data on the velocity vector kinetic energy and turbulence intensity in the complex turbulence field. In this study. three kinds of rod shape such as square. triangle. and semicircle are selected as the turbulence promoter. Nozzle diameters are 10mm. 17mm. and 23mm. And the analysis of the flow characteristics due to the above rods is carried out at Re No. 2.000, 3.000. and 4,000 by PIV measurement. It is clarified that the rod setup is very useful to obtain the turbulence enhancement and the turbulence intensity according to the shapes of rod appears large in order of the shapes of rod such as square 〉 triangle 〉semicircle.

• 한국수자원학회논문집
• /
• 제48권4호
• /
• pp.291-298
• /
• 2015

본 연구의 목적은 하천에서 흐름방향 유속의 횡분포식에 기반하여 1차원 종분산계수를 이론적으로 유도하고 이들의 타당성을 검증하는 것이다. 이를 위해 본 논문의 전편 "I. 흐름방향 유속의 횡포식"에서는 Shiono-Knight Model (일명 SKM)을 도입하여 삼각형 단면수로에서 횡분포식을 해석적으로 유도하였다. 본 논문의 후편 "II. 종분산계수"에서는 전편에서 유도된 유속의 횡분포식을 Fischer (1968)의 삼중 적분식에 대입하여 1차원 종분산계수 이론식을 새롭게 개발하였다. 본래 SKM은 Navier-Stokes 방정식을 근간으로 개발되어 주로 직선수로이면서 사다리꼴 단면이나 복단면 수로에 적용되어 왔지만, 본 연구에서는 사행으로인한 최심선의 변동을 고려할 수 있는 삼각형을 단면형상으로 가정하였다. 유도된 해석해를 검증하기 위해 자연하천에서 실측된 유속자료와 비교 분석하였다. 또한 유도된 횡분포식을 이용하여 단면평균유속을 산정하고, 이를 Manning의 유속식의 결과와 비교 검증하였다. 본 연구에서 개발한 이론식은 비록 유속의 횡분포를 경우에 따라서 섬세하게 재현하지는 못하더라도 조도계수를 포함한 몇 가지 기본적인 수리 및 지형자료만 측량한다면 유속의 관측없이 비교적 정확한 유속분포를 산출해 낼 수 있는 장점이 있었다.

• 지구물리와물리탐사
• /
• 제11권3호
• /
• pp.230-241
• /
• 2008

주변 잡음 자료를 이용한 부지 특성 규명 방법으로 삼각형 배열, 육각형 배열, 반원형 배열에 따른 표면파 분산곡선의 도출 특성을 파악하였고, 터키 이즈밋시의 인근 부지에 대한 부지특성을 살펴보기 위하여 주변 잡음 자료로부터 표면파 분산곡선과 H/V비를 도출하였다. 또한 MASW를 수행하여 고주파 분산곡선인 기본 모드와 1차 모드 분산곡선을 도출하였고 역산을 수행하여 S파 속도 구조를 구하였다. 표면파를 이용한 5파 속도 구조 규명에서는 역산시 비유일해의 문제가 발생하므로, MASW자료의 초동을 이용한 굴절법 토모그래피를 동시에 수행하여 얻어진 속도구조 비교를 통해서 유일해를 결정하였다.

• 한국전산유체공학회지
• /
• 제16권2호
• /
• pp.66-74
• /
• 2011

The SCR catalyst in coal-fired power plant is eroded by the collision of fly ash on the catalyst surface. However the erosion of SCR catalyst by the collision of fly ash has not been fully studied, especially in terms of fluid dynamics. Hence, in the present study, we focus on the gas and solid flows inside the SCR catalyst duct and their consequent effect on the erosion characteristics. For this purpose, computational fluid dynamics is applied to investigate the two-phase flows and to evaluate the erosion rate for different flow and particle injection conditions. Also, the erosion rate and pressure drop of commonly used square shape are compared with equilateral triangle and hexagon shapes. The pressure drop of SCR catalyst is increased when SCR catalyst surface area per unit volume increases. The erosion rate of SCR catalyst is enhanced when the particle velocity, mass flow rate of particle, particle diameter and cell density of SCR catalyst are increased. From the results, the pressure drop and erosion rate at the catalyst surface can be minimized by reducing cell density of SCR catalyst to decrease particle velocity and number of particle impacts.