• The Journal of Korea Robotics Society
• /
• v.11 no.4
• /
• pp.285-292
• /
• 2016

For articulated swimming robots, there have been no researches about controlling the motion or trajectory following. A control method for articulated swimming robot is suggested by extending a previous algorithm, ESPG (Extended Swimming Pattern Generator). The control method focuses on the situation that continuous pre-determined swimming pattern is applied for long range travelling. In previous studies, there has not been a way to control the propulsive force when a swimming pattern created by ESPG was in progress. Hence, no control could be made unless the swimming pattern was completed even though an error occurred while the swimming pattern was in progress. In order to solve this problem, this study analyzes swimming patterns and suggests a method to control the propulsive force even while the swimming pattern was in progress. The angular velocity of each link is influenced and this eventually modifies the propulsive force. However, The angular velocity is changed, a number of problems can occur. In order to resolve this issue, phase compensation method and synchronization method were suggested. A simple controller was designed to confirm whether the suggested methods are able to control and a simulation has affirmed it. Moreover, it was applied to CALEB 10 (a biomimetic underwater articulated robot) and the result was verified.

• Journal of Institute of Control, Robotics and Systems
• /
• v.16 no.3
• /
• pp.256-263
• /
• 2010

The paper proposes a sensorless speed control strategy for a PMSM (Permanent Magnet Synchronous Motor) based on a new SMO (Sliding Mode Observer), which substitutes a signum function with a sigmoid function. To apply robust sensorless control of PMSM against parameter fluctuations and disturbance, the high speed SMO is proposed, which estimates the rotor position and angular velocity from the back EMF. The low-pass filter and additional position compensation of the rotor are used to reduce the chattering problem commonly found in sliding mode observer with signum function, which becomes possible by applying the sigmoid function with the control of a switching function. Also the proposed sliding mode observer with the sigmoid function has better efficiency than the conventional sliding mode observer since it adjusts the observer gain by variable boundary layer and estimates the stator resistance. The stability of the proposed sliding mode observer is verified by the Lyapunov second method in determining the observer gain. The validity of the proposed high speed PMSM sensorless velocity control has been demonstrated by real experiments.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.13 no.4
• /
• pp.708-715
• /
• 2010

In Strapdown Inertial Navigation System, alignment accuracy is the most important factor to determine the performance of navigation. However by an existing self-alignment method, it takes a long time to acquire the alignment accuracy that we want. So, to attain the desired alignment accuracy in as little as $\bigcirc$ minutes, we have developed the precise multi-position alignment method. In this paper, it is proposed a inertial measurement matching transfer alignment method among alignment methods to minimize the alignment error in a short time. It is based on a mixed velocity-DCM matching method be suitable to the operating environment of vertical launching system. The compensation methods to reduce misalign error, especially azimuth angle error incurred by measurement time-delay error and body flexure error are analyzed and evaluated with simulation. This simulation results are finally confirmed by experimentations using FMS(Flight Motion Simulator) in Lab and the integration test to follow the fire control mission.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.11
• /
• pp.5194-5201
• /
• 2011

In this paper, an adaptive nonlinear friction compensation scheme for second-order nonlinear mechanical system with a partially known nonlinear dynamic friction is proposed to achieve asymptotic position and velocity tracking in the absence of disturbances and modeling errors. It is also shown that even with disturbances and modeling errors, in contrast to existing other adaptive control schemes, by proper adjustment of design parameters, reduced error bounds on position and velocity tracking can be achieved.

• Journal of Navigation and Port Research
• /
• v.40 no.5
• /
• pp.241-247
• /
• 2016

The tracking filter plays a key role in the accurate estimation and prediction of maneuvering a vessel's position and velocity when attempting to enhance safety by avoiding collision. Therefore, in order to achieve accurate estimation and prediction, many oceangoing vessels are equipped with the Automatic Radar Plotting Aid (ARPA) system. However, the accuracy of prediction depends on the tracking filter's ability to reduce noise and maintain a stable transient response. The purpose of this paper is to derive the optimal values of the gain parameters used in tracking a High Dynamic Warship. The algorithm employs a ${\alpha}-{\beta}-{\gamma}$ filter to provide accurate estimates and updates of the state variables, that is, positions, velocity and acceleration of the high dynamic warship based on previously observed values. In this study, the filtering coefficients ${\alpha}$, ${\beta}$ and ${\gamma}$ are determined from set values of the damping parameter, ${\xi}$. Optimization of the damping parameter, ${\xi}$, is achieved experimentally by plotting the residual error against different values of the damping parameter to determine the least value of the damping parameter that results in the optimum smoothing coefficients leading to a reduction in the noise corruption effect. Further investigation of the performance of the filter indicates that optimal smoothing coefficients depend on the initial and average velocity of the target.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.38 no.2
• /
• pp.191-198
• /
• 2001

As a method to compensate the deterioration of the picture quality which was caused by beam profile characteristic in the CRT and the projection screen of HD projection TV, a linear scan velocity modulation(SVM) method has been employed, whose modulation velocity is linearly proportional to the variation in the video signal amplitude. However, the effect of picture quality improvement is not uniform with video signal amplitude in the linear SVM. In this paper, for the optimum SVM effect, we analyze the beam profile characteristic on the HD projection screen and we analyze the SVM effect as function of the differentiated pulse width, the differentiated pulse amplitude and the input signal amplitude. Finally we confirm that the nonlinear SVM method is necessary to get uniform image compensation in the HD projection TV, and we implement the nonlinear SVM circuit. The performance of the realized SVM circuit with nonlinear amplitude transfer characteristic is confirmed as uniform improvements in picture quality.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.8 no.6
• /
• pp.1381-1387
• /
• 2007

Up to now, various continuous-processing systems are used in many industrial applications such as textile machines, paper-making machines, printing machines, and so on. In these applications, the tension forced on the products in the control volume can be changed according to the velocity difference between the feeding roll and the delivery roll. Specially, the tension variation generated by the velocity difference, or the inertial effect can decreases the quality of the products in the textile process. In this paper, the tension control problem in a circular knitting machine system is treated to cope with these problems. Firstly, the tension relationship in the winding mechanism of general continuous-processing systems is modeled. Next, to effectively drive the feeding and delivery rolls in the circular knitting machine system, a new tension control method is presented by considering the inertia compensation and the velocity difference between the feeding roll and the delivery roll. Through the experimental works, it is shown that the proposed tension control method can be used to improve the performance of tension control in the control volume of the given circular knitting machine system.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.40 no.12
• /
• pp.1067-1076
• /
• 2016

This paper describes the development of a hybrid-powered wheelchair (HPW) for the elderly. The proposed HPW has novel mechanical and control features compared with conventional powered wheelchairs. An ergonomic back-braking mechanism was designed in order to stop the wheels easily. In terms of control features, the HPW remarkably reduces the muscle power required by combining various assistive functions, such as wheel torque assistance, friction/inertia compensation, gravity compensation, and the one-hand driving algorithm. For wheel torque assistance, strain gauges were attached to the hand-rim in order to measure the wheel torque applied by a human. Gyroscopes and an accelerometer were attached to the wheel and chair respectively for friction and inertia compensation. An inclinometer was attached for gravity compensation and the one-hand driving algorithm was included for patients who can only use one hand. The one-hand driving algorithm controls the angular velocity of the uncontrolled wheel by using a gyroscope and pressure sensors attached to the bottom of the seat. Finally, the performance of the proposed motion assisted algorithm was verified through various experiments.

• Journal of Institute of Control, Robotics and Systems
• /
• v.10 no.12
• /
• pp.1256-1263
• /
• 2004

Output feedback passivation problem is studied when the given system is not minimum-phase or does not have relative degree one. Using a parallel connection with an additional dynamics, the authors provide a dynamic output feedback control law which renders the composite system passive. Sufficient conditions are presented under which the composite system is output feedback passive. As an application of the dynamic passivation scheme, a point-to-point control law for a flexible joint robot is presented when only the position measurements are available. This provides an alternative way of replacing the role of the velocity measurements for the proportional-derivative (PD) feedback law. The performance of the proposed control law is illustrated in the simulation studies of a manipulator with three revolute elastic joints.

• Journal of Institute of Control, Robotics and Systems
• /
• v.5 no.4
• /
• pp.462-470
• /
• 1999

In this paper, we proposed a cross-couple controller for compensating nonlinear friction of the X-Y table of CNC machines. Due to the nonlinearity of the frictions, large contour errors, referred to as quadrant glitches, occur when each axis of the X-Y table makes a zero velocity crossing. To reduce the quadrant glitches the friction compensators and nonlinear friction observers for estimating Coulomb frictions are employed in the proposed method. A hyperbolic tangent function is used in reducing the magnitude of quadrant glitches and the CEM (Contour Error Model) is utilized for the estimation of the velocities. The performance of the proposed compensators is evaluated for several trajectories by computer simulations.