• Transactions of the Korean Society of Automotive Engineers
• /
• v.13 no.1
• /
• pp.166-173
• /
• 2005

A vehicle stability control logic for 4WD hybrid electric vehicle is proposed using the regenerative braking of the rear motor and electronic brake force distribution module. Performance of the stability control logic is evaluated for J-turn and single lane change. It is found from the simulation results that the regenerative braking at rear motor is able to provide improved stability compared with the vehicle performance without my stability control. Additional improvement can be achieved by applying the regenerative braking plus electronic brake farce distribution control. It is expected that the regenerative braking offers additional improvement of the fuel economy as well as the vehicle stability control.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.67 no.12
• /
• pp.1723-1728
• /
• 2018

In order to investigate the voltage drop compensation effect of AT for domestic railway vehicle base, the parameters of AT voltage drop of railroad car base are Z3 (Impedance of feeder line), Xn ( Distance from railroad vehicle to AT to SS), and Dn (distance between both ATs of railway vehicle).In addition, when installed in a SSP for a railway vehicle base, there is no AT and feeder line in the railway vehicle base except for the SSP for the main line and the SSP for the railway vehicle base, so that if zero or ignored, the AC single-phase two- It can be confirmed that it becomes a form.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.2
• /
• pp.151-155
• /
• 2008

KHST(Korean High Speed Train) has been utilized the total measurement system which evaluates the efficiency and a breakdown of the vehicle and it's results effect to secure reliability of the vehicle. Generally KHST has been received pulse signals from the wheel. It calculates the travel distance after counter the signals to confirm location information of the vehicle. However, there is a limit to measure the location of the vehicle due to slip, slide and the wheel attrition. We have developed a new measurement system by using GPS to complement those errors. In general, GPS receivers are composed of an antenna, tuned to the frequencies transmitted by the satellites, receiver-processors, and a highly-stable clock The GPS mounted on the roof of TT4 in KHST receives a signal from the RS232 communication port. It is connected to the network system in TT3 after converting with TCPIP communication. It is able to track the position of vehicle and synchronize the signal from different measurement system simultaneously. Therefore it is able to chase the fault occurrence, track inspection and electrical interruption at real-time situation more accurately. There is not an error coursed by vehicle conditions such as slip and the slide.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2011.05a
• /
• pp.263-266
• /
• 2011

Drivers check always vehicle state for own safety and is necessary to understand about vehicle state. If driver know vehicle state, because driver request vehicle state at vehicle specialty company, driver pay a lot of money and waste a lot of time. Now, drivers have checked vehicle state by using variety features of smart phone due to progress of IT(Information Technology). but existing smartphone vehicle diagnostic system learned professional knowledge of vehicle and know vehicle state. drives not need vehicle diagnostic. to overcome these disadvantages, there use easily drivers by using smartphone and request system to know own all vehicle state. In this paper, there implement vehicle diagnostic system with smartphone based on android OS to use easily this system and know check information of vehicle supplies replacement cycles, vehicle internal problems, Eco driving by using OBD-II data to receive by OBD-II Protocol convert Bluetooth connector.

• Journal of computational fluids engineering
• /
• v.18 no.3
• /
• pp.8-13
• /
• 2013

Drag reduction of a running vehicle is very important issue for the energy savings and emission reduction of its power train. Especially for a solar powered electric vehicle, the drag reduction and weight lightening are two serious problems to be solved to extend its driving distance under the given energy condition. In this study, the ground effect of an airfoil shaped road vehicle was studied for an optimum body design of an ultra-light solar powered electric vehicle. Clark-Y airfoil type was adopted to the body shape of the model vehicle to reduce aerodynamic drag. From the study, it was found that the drag of the model vehicle was reduced as the height(h) between ground and the lower surface of the model vehicle was decreased. It is due to the reduction of the down-wash decreasing the induced drag of the vehicle. The lift was also decreased as the height decreased. It is due to the turbulent boundary layer developed beneath the vehicle body. The drag is classified into two types; the form and friction drag. The fraction of form drag to friction one is 76 to 24 on the model vehicle. As the height(h) of the model vehicle from the ground surface increases the form drag also increases but the friction drag is in reverse.

• Journal of Korea Society of Industrial Information Systems
• /
• v.27 no.6
• /
• pp.59-68
• /
• 2022

We propose the vehicle maintenance support system to alarm consumable replacement reminders to the vehicle owner. Since the delayed replacement of the consumables makes the condition of the vehicle worse, it is crucial to replace consumables in a recommended period. The vehicle maintenance support system alarms the replacement time, which is set by the vehicle owner, based on the mileage of the installed vehicle. It integrates speed information acquired from the Controller Area Network interface for communication between Electronic Control Unit and instrument panel, exposed at the On Board Diagnostics-II port, to calculate the vehicle mileage. By this, there is no additional wiring required for the system. We verify the system has only 0.28% error by comparing the mileage on the system with the instrument cluster on the vehicle. It automatically enters low-power mode consuming 15mW, which is a negligible amount for the typical conditions of the car, to prevent the vehicle battery from discharging when the ignition is off.

• Journal of Power System Engineering
• /
• v.7 no.3
• /
• pp.61-68
• /
• 2003

Steering characteristics is an important factor in the evaluation of vehicle quality. To estimate steering characteristics in the vehicle conceptual design stage, vehicle dynamics simulation methods are very efficient. However, it is often difficult to simulate vehicle dynamics for the specific driving scenarios in open-loop driving environment. An efficient driver-in-the-loop vehicle model will be efficient for this job. A good tire model is also very important for the accurate vehicle dynamics simulation. In this research, a driver model is used to simulate vehicle steering dynamics for a 8-dof vehicle model with STI(Systems Technology, Inc.) tire model. For the demonstration of this model, a SUV(sports utility vehicle) and a sedan were simulated.

• Journal of Auto-vehicle Safety Association
• /
• v.11 no.2
• /
• pp.6-10
• /
• 2019

This paper describes effectiveness of accident reduction on vehicles equipped with AEB using accident data occurring in Korea. During the statistical period, we used the number of vehicles which are covered by auto insurance and the number of accidents. To maximize the reduction effect of accidents caused by the driver's carelessness, the analysis was limited to Physical Damage Coverage that covers the cost of repairing or replacing the damaged vehicle caused by the driver's fault. Due to Personal Information Protection Law, it was not capable of comparing the same vehicle using Vehicle Identification Number in this study. Instead of that, we used it as a similar vehicle, so there are limits to the comparison and analysis results. As a result of this study, we have found that the effect of reducing accidents was different depending on the vehicle class, but it was generally concluded that the number of accidents decreased when the vehicle was equipped with an AEB system. Domestic research on the AEB effect of reducing accidents is not active yet. Therefore, it is absolutely essential to analyze the effects according to various conditions such as driver's age, occupation and gender as well as expanding the study models in the future.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.15 no.11
• /
• pp.2347-2352
• /
• 2011

driver for safety always check the status of their vehicle, and it is essential to understand. But if you want to know the status of the driver of the vehicle in specialist referral time and money because it costs the operator shall be paid.IT technoligy with the development of the various features of your phone to check the status of the vehicle was able to do. However, the car' existing phone system, car diagnostic expertise must be learned because it will reveal the status of the vehicle do not have the expertise to not highlight the need for diagnostic. To reflect these points in smartphone users to easily use their own vehicles at a time to determine the status of a system that is required. In this paper, OBD-II protocol conversion WiFi OBD-II connector, retrieving information from the driver of the vehicle replacement cycle of consumables required vehicle inspection, vehicle problems in real-time diagnostic information to the user ease of use shows the iPhone implementation in the automotive supply was implemented based on the smartphone.

• Asia-pacific Journal of Multimedia Services Convergent with Art, Humanities, and Sociology
• /
• v.8 no.2
• /
• pp.33-40
• /
• 2018

There are lots of literature about connected car system from industry and academia. The connected car is a smart car integrated with IT technology that is connected to people, vehicles and traffic management systems. It is important to V2I (vehicle to infrastructure) communication which is the connection between the vehicle and the infrastructure. CIM (cooperative intersection management) is a device to manage the communication between vehicle and infrastructure. In this paper, we analyze two intelligent vehicle control methods using CIM at non-signalized intersections. In the first method, a vehicle to pass through intersection needs to reserve a resource of intersection. In the second method, trajectory patterns on pre-planned vehicles are classified to pass through intersection. We analyze case studies of two methods to be implemented by DP(dynamic programming) and ACO(ant colony optimization) algorithms. The methods can be reasonably improved by placing importance on vehicles or controlling speeds of vehicles.