• 한국분무공학회지
• /
• 제27권2호
• /
• pp.94-100
• /
• 2022

Even in non-road UTV (Utility Terrain Vehicle), spark ignition engines are often used to reduce emissions. In this study, gasoline and LPG (Liquified Petroleum Gas) fuels were applied to UTV engines, and the exhaust gas and combustion stability were compared through engine tests. A 0.8-liter two-cylinder SI engine was used in the experiment. Experiments were conducted while changing the IVO (Intake Valve Open) and EVC (Exhaust Valve Close) at 1500 rpm 14 N·m, 40 N·m, and 3000 rpm 17 N·m, 44 N·m conditions. As a result of the experiment, when the valve overlap increased according to the change of IVO and EVC, combustion stability decreased and THC emission increased, but NOx decreased. Comparing the LPG engine with the gasoline engine, the amount of CO₂ and PN (Particulate Number) generation decreased in the LPG engine, and the combustion stability was good.

• 한국가스학회지
• /
• 제20권6호
• /
• pp.9-15
• /
• 2016

가스연료인 LPG와 CNG는 청정 대체연료로서 차량용 연료로 많이 사용되고 있다. 특히 CNG의 경우 저탄소 연료로서 온실가스 배출량 저감에 기여할 수 있다, LPG의 경우 가솔린 차량과 거의 동등한 성능을 가지면서도 연료가격이 저렴하여 택시에 많이 사용되고 있다. 본 연구에서는 동일차량에서 LPG와 CNG를 사용하여 배출가스와 최근 문제가 되고 있는 입자상물질의 배출개수(PN; particle number)에 대하여 비교하였다. 차대동력계를 이용하여 FTP-75와 WLTC 모드에 대하여 시험을 진행하였다. PN은 두 대의 CPC(Condensation Particle Counter)를 이용하여 5 nm 이상과 23 nm 이상의 입자에 대하여 배출 개수를 측정하였다. 배출가스에 있어서는 CO2의 경우 LPG 차량이, 메탄의 경우 CNG 차량이 많이 배출되었다. PN의 경우 두 연료에서 배출되는 PN은 비슷한 수준이었으며, WLTC 에서 고속운전하는 동안 23 nm 이하 크기의 입자 배출 개수가 많았다.

• 한국대기환경학회지
• /
• 제30권5호
• /
• pp.449-460
• /
• 2014

Since the emergence of domestically produced automobiles in 1964, the number of automobiles in circulation in South Korea has increased constantly. With this rapidly increasing number of automobiles, automobile-induced environmental pollution has become an issue of great concern, especially with regard to air pollution. Of the carbon composites contained in automobile exhaust gas, PAHs are known to be carcinogenic and highly deleterious to humans and thus need to be urgently mitigated. To address this issue of PAHs, this study was conducted to estimate qualitative of particulate PAHs contained in carbon composites in automobile exhaust gas, by capturing all particulate matter discharged from the latter. To allow for differentiated analyses, the automobiles investigated were divided into 4 groups: gasoline vehicle, motocycle, diesel vehicle, and LPG vehicle. Samples were analyzed using two methods. First, in-depth analysis was performed on organic carbon (OC) and elemental carbon (EC) composites with analysis parameters, using the Thermal Optical Transmittance Method (NIOSH 5040). Second, for the examination of particulate PAHs, GC/MSD was used to analyze the 16 PAH species specified by the Environmental Protection Agency (EPA). The analyses yielded the findings that diesel vehicles had the highest mass concentration ($2,007{\mu}g/m^3$), followed by motocycle ($1,066{\mu}g/m^3$), LPG vehicle ($392{\mu}g/m^3$), and gasoline vehicles ($270{\mu}g/m^3$). The highest carbon concentrations in total particulate matter by vehicle weight were produced from LPG vehicle (79.8%), followed by gasoline vehicle (77.4%), motocycle (69.8%), and diesel vehicle (59.1%).

• 한국산학기술학회논문지
• /
• 제19권6호
• /
• pp.689-695
• /
• 2018

본 연구는 배기가스 기준을 만족하기 위해 차량에 장착된 배기가스 후처리 장치(DPF)의 재생제어 방안에 대한 것이다. DPF는 배기가스에 포함된 입자상 물질(PM)을 포집하기 위한 필터로 DPF에 포집된 PM은 일정 조건에 이르렀을 때 고온의 배기가스로 연소시킨다. 이러한 과정을 재생(Regeneration)이라 하는데 DPF의 정상적인 성능을 위한 필수 과정이다. 재생이 잘 되지 않을 경우, 차량의 성능저하와 심한 경우 차량의 화재로도 이어질 수 있다. DPF의 재생은 제어로직에 의해 수행되는데 재생제어 로직이 차량의 운용특성을 제대로 반영하지 못한 경우 DPF 재생이 이루어지지 않을 수 있다. 그렇기 때문에 전술차량의 운용특성을 파악하여 DPF가 정상적으로 재생될 수 있도록 하는 것이 매우 중요하다. 본 연구에서는 전술차량의 운용 특성과 DPF의 특성을 분석하여 이에 맞는 DPF의 재생 제어 로직을 추가하고자 한다. 더불어 추가된 재생 제어 로직에 따른 운용 시 발생될 수 있는 추가적인 문제점까지 동시에 개선하고자 한다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2007년도 추계학술대회논문집
• /
• pp.913-917
• /
• 2007

The turbocharger for a vehicle is consisting of a centrifugal compressor and turbine. These compressor and turbine are vibrating and emitting noises through the T/C body, exhaust system (Catalyst, Bellows, Pipe, etc) and Intake system (Hoses, Intercooler pipes, Intercooler) as rotating. A turbocharger cold test bench is constructed to reduce these noises, especially for the purpose of realizing transient operating environment and oil temperature control to simulate the vehicle operating characteristics with intake system and exhaust system. This research laid the groundwork to develop a lower noise level T/C through understanding the mechanism of the noise source of T/C.

• 한국분무공학회지
• /
• 제12권1호
• /
• pp.65-70
• /
• 2007

This paper is to investigate the characteristics of exhaust emissions and nano-particle emission from diesel passenger vehicle according to using biodiesel fuel as an alternative fuel. In this work, the particulate matters (PM) of exhaust emissions in diesel engine were investigated by number of particles and mass measurement. The mass of the total PM was measured using the standard gravimetric measurement method, the total number concentrations were measured on a ECE15+EUDC driving cycle using Condensation Particle Counter (CPC). Total PM emission was reduced $2{\sim}38%$ and number concentration was reduced $1{\sim}27%$ according to increasing blended ratio of biodiesel with diesel fuel. Total PM emission was reduced more than particle number emission because volatile particles were measured in total PM but were not measured in particle number emissions.

• 소성∙가공
• /
• 제25권3호
• /
• pp.176-181
• /
• 2016

The exhaust tail pipe is the only visible part of the exhaust system on a vehicle. The conventional way to make the tail pipe is welding after stamping. There are various problems that occur during the stamping of stainless steel sheets such as scratching and local fracture. Problems during welding can also occur due to poor weldability. Tube hydroforming can be a solution, which eliminates these problems. The current study deals with the development of tube hydroforming for a vehicle tail pipe using finite element analysis for a free-feeding method. The current study focuses on the development of a proper load path for the tail pipe hydroforming and how bending influences the subsequent processing steps. The FE analysis results were compared with experimental results. This study shows the importance of bending and the necessity of considering bending when performing a tube hydroforming analysis.

• 한국가시화정보학회지
• /
• 제8권1호
• /
• pp.25-30
• /
• 2010

The flow characteristics under recirculation cool vent mode is numerically studied using commercial fluid dynamic code(CFX). For the reliable analysis, real vehicle and human FE model is employed in grid generation process. The geometrical location and shape of panel vent, and exhaust vent is set as that of real vehicle model. The flowrate of the working fluid is determined as 330CMH which is equivalent to 70 percent of maximum capacity of HVAC system. The high velocity regions are formed around 4 each panel vent. Because of the non-symmetrically located exhaust, non-uniform flow and partial backflow near the door trim is observed. Streaklines start from each panel vent show the flow pattern of the airflow in the passenger's compartment very well.

• 터널과지하공간
• /
• 제6권1호
• /
• pp.64-68
• /
• 1996

Analyzed in this paper is fluid flow in the region near the exhaust and blower ports of the ventilation ducts inside a vehicle tunnel. Theoretical analysis shows that prediction of the energy loss in this region is important for designing the ventilation system. A finite-difference numerical model for the two-dimensional turbulent flow field was used to obtain the flow solution as well as the energy loss. It was shown that the blower-nozzle angle ($\beta$) had an important role in establishing both the pressure gradient and the energy loss, while the effect of the distance between two ports on them was not so significant.

• 한국대기환경학회:학술대회논문집
• /
• 한국대기환경학회 2008년도 추계학술대회 논문집
• /
• pp.75-77
• /
• 2008