• Journal of Mechanical Science and Technology
• /
• v.17 no.5
• /
• pp.654-667
• /
• 2003

This paper presents a consequence of the systematic approach to identify the aerodynamic parameters of an unmanned aerial vehicle (UAV) equipped with the automatic flight control system. A 3-2-1-1 excitation is applied for the longitudinal mode while a multi-step input is applied for lateral/directional excitation. Optimal time step for excitation is sought to provide the broad input bandwidth. A fully automated programmed flight test method provides high-quality flight data for system identification using the flight control computer with longitudinal and lateral/directional autopilots, which enable the separation of each motion during the flight test. The accuracy of the longitudinal system identification is improved by an additional use of the closed-loop flight test data. A constrained optimization scheme is applied to estimate the aerodynamic coefficients that best describe the time response of the vehicle. An appropriate weighting function is introduced to balance the flight modes. As a result, concurrent system models are obtained for a wide envelope of both longitudinal and lateral/directional flight maneuvers while maintaining the physical meanings of each parameter.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.27 no.6
• /
• pp.455-463
• /
• 2022

This study proposes a receiving pad identification coil for wireless charging of electric vehicles. The proposed coil identifies the shape of the receiving pad through magnetic coupling with the receiving pad. Therefore, the shape of the coil is designed to show the different magnetic properties of each receiving pad. The accuracy of this design is verified through finite element method simulation. Furthermore, the operation method of the secondary pad identification circuit is described, and the appropriate magnitude and length of the pulse voltage applied to this circuit for receiving pad identification are derived through simulation. The performance of the proposed identification coil set is verified by the experimental results.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.10 no.6
• /
• pp.2483-2503
• /
• 2016

Traffic congestion is a severe problem in many modern cities around the world. Real-time and accurate traffic congestion identification can provide the advanced traffic management systems with a reliable basis to take measurements. The most used data sources for traffic congestion are loop detector, GPS data, and video surveillance. Video based traffic monitoring systems have gained much attention due to their enormous advantages, such as low cost, flexibility to redesign the system and providing a rich information source for human understanding. In general, most existing video based systems for monitoring road traffic rely on stationary cameras and multiple vehicle tracking method. However, most commonly used multiple vehicle tracking methods are lack of effective track initiation schemes. Based on the motion of the vehicle usually obeys constant velocity model, a novel vehicle recognition method is proposed. The state of recognized vehicle is sent to the GM-PHD filter as birth target. In this way, we relieve the insensitive of GM-PHD filter for new entering vehicle. Combining with the advanced vehicle detection and data association techniques, this multiple vehicle tracking method is used to identify traffic congestion. It can be implemented in real-time with high accuracy and robustness. The advantages of our proposed method are validated on four real traffic data.

• Journal of Korean Society of Transportation
• /
• v.23 no.8 s.86
• /
• pp.147-152
• /
• 2005

This study firstly developed a tool for evaluating performance requirements of automatic vehicle identification (AVI) techniques. A microscopic traffic simulator, Paramics, was employed to investigate the effects of AVI performances on the accuracy of estimating section travel times. Mote Carlo simulation approach was incorporated into Paramics to conduct systematic evaluations of identifying required AVI performances. The proposed method in this study can serve as a logical and necessary precursor to field implementation of a variety of AVI techniques toward achieving more reliable traffic information.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.6
• /
• pp.142-155
• /
• 2000

A MIMO model reference control scheme incorporating the variable structure theory for a vehicle four wheel steering system(4WS) is proposed and evaluated for a class of continuous-time nonlinear dynamics with known or unknown uncertainties. The scheme employs an neural network to identify the plant systems, where the neural network estimates the nonlinear dynamics of the plant. By the Lyapunov direct method, the algorithm is proven to be globally stable, with tracking errors converging to the neighborhood of zero. The merits of this scheme is that the global system stability is guaranteed and it is not necessary to know the exact structure of the system. With the resulting identification model which contains the neural networks, it does not need higher degrees of freedom vehicle model than 3 degree of freedom model. Th proposed scheme is applied to the active four wheel system and shows the validity is used to investigate vehicle handing performances. In simulation of the J-turn maneuver, the reduction of yaw rate overshoot of a typical mid-size car improved by 30% compared to a two wheel steering system(2WS) case, resulting that the proposed scheme gives faster yaw rate response and smaller side angle than the 2WS case.

• Smart Structures and Systems
• /
• v.30 no.1
• /
• pp.107-119
• /
• 2022

Modal parameters are widely used in bridge damage detection, finite element model (FEM) updating and design optimization. However, the conventional modal identification approaches require large number of sensors, enormous data processing workload, but normally result in mode shapes with low accuracy. This paper proposes a modal identification method of time-varying vehicle-bridge system using a single sensor. Firstly, the essential physical relationship between the instantaneous frequency of the vehicle-bridge system and the bridge mode shapes are derived. Subsequently, based on the synchroextracting transform, the instantaneous frequency of the system is tracked through the dynamic response collected by a single sensor, and further the modal parameters are estimated by using the derived physical relationship. Then numerical and experimental examples are conducted to examine the feasibility and effectiveness of the proposed method. Finally, the modal parameters identified by the proposed method are applied in bridge FEM updating. The results manifest that the proposed method identifies the modal parameters with high accuracy via a single sensor, and can provide reliable data for the FEM updating.

• Journal of Auto-vehicle Safety Association
• /
• v.12 no.2
• /
• pp.27-32
• /
• 2020

This paper presents steering system requirements to ensure the stabilized lateral control of autonomous driving vehicles. The two main objectives of a lateral controller in autonomous vehicles are maintenance of vehicle stability and tracking of the desired path. Even if the desired steering angle is immediately determined by the upper level controller, the overall controller performance is greatly influenced by the specification of steering system actuators. Since one of the major inescapable traits that affects controller performance is the time delay of the steering actuator, our work is mainly focused on finding adequate parameters of high level control algorithm to compensate these response characteristics and guarantee vehicle stability. Actual vehicle steering angle response was obtained with Electric Power Steering (EPS) actuator test subject to various longitudinal velocity. Steering input and output response analysis was performed via MATLAB system identification toolbox. The use of system identification is advantageous since the transfer function of the system is conveniently obtained compared with methods that require actual mathematical modeling of the system. Simulation results of full vehicle model suggest that the obtained tuning parameter yields reduced oscillation and lateral error compared with other cases, thus enhancing path tracking performance.

• Journal of Institute of Control, Robotics and Systems
• /
• v.2 no.2
• /
• pp.121-126
• /
• 1996

The hydrodynamic coefficients estimation (HCE) is important to design the autopilot and to predict the maneuverability of an underwater vehicle. In this paper, a system identification is proposed for an HCE of an underwater vehicle. First, we attempt to design the HCE algorithm which is insensitive to initial conditions and has good convergence, and which enables the estimation of the coefficents by using measured displacements only. Second, the sensor and measurement system which gauges the data from the full scale trials is constructed and the data smoothing algorithm is also designed to filter the noise due to irregular fluid flow without changing the data characteristics itself. Lastly the hydrodynamic coefficients are estimated by applying the measured data of full scale trials to the developed algorithm, and the estimated coefficients are verified by full scale trials.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.2
• /
• pp.158-165
• /
• 2006

In this paper, a new uni-axial bushing model for vehicle dynamics analysis is proposed. Bushing components of a vehicle suspension system are tested to capture the nonlinear and hysteric behavior of the typical rubber bushing elements using the MTS machine. The results of the tests are used to develop the Bouc-Wen bushing model. The Bouc-Wen model is employed to represent the hysteretic characteristics of the bushing. ADAMS program is used for the identification process and VisualDOC program is also used to find the optimal coefficients of the model. Genetic algorithm is employed to carry out the optimal design. A numerical example is suggested to verify the performance of the proposed model.

• Structural Engineering and Mechanics
• /
• v.21 no.3
• /
• pp.369-374
• /
• 2005

A big progress has been made for moving force identification from bridge dynamic responses in recent years. Current knowledge and the potentials on moving force identification methods are reviewed in this paper under main headings below: background of moving force identification, experimental verification in laboratory and its application in field.