• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.15 no.1
• /
• pp.58-70
• /
• 1990

This paper describes a VLSI implementation of real-time two dimensional DCT processor for the subprimary rate video codec system. The proposed architecture exploits the parallelism and concurrency of the distributes architecture for vector inner product operation of DCT and meets the CCITT performance requirements of video codec for full CSIF 30 frames/sec. It is also shown that this architecture satisfies all the CCITT IDCT accuracy specification by simulating the suggested architecture in bit level. The efficient VLSI disign methodology to design suggested architecture is considered and the module generator oriented design environments are constructed based on SUN 3/150C workstation. Using the constructed design environments. the suggensted architecture have been designed by double metal 2micron CMOS technology. The chip area fo designed 8x8 2-D DA-DCT (Distributed Arithmetic DCT) processor is about 3.9mmx4.8mm.

• Journal of Sensor Science and Technology
• /
• v.26 no.1
• /
• pp.66-72
• /
• 2017

The three dimensional ultrasonic anemometer was constructed to reduce the disadvantages of the two-dimensional anemometer and to be free from the use environment. Three pairs of transmitting and receiving ultrasonic sensors were designed to face each other at an angle of $45^{\circ}$ to the upper and lower surfaces at intervals of $120^{\circ}$. 200 kHz ultrasonic sensor Oscillation, transmission and reception, level detection, power supply circuit were designed and U, V, W wind speed vector components were obtained by measuring the time of first received ultrasonic pulse by transmitting pulse ultrasound. It is implemented as firmware in ARM Coretex-M3 processor so that horizontal and vertical wind direction and wind speed can be converted into digital signal by vector calculation. In this study, The three-dimensional ultrasonic anemometer can complement the disadvantages of the two-dimensional anemometer (mechanical and ultrasonic), and it is expected to gradually replace the two-dimensional anemometer due to its high utilization rate by collecting additional information such as vertical wind.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.54 no.3
• /
• pp.154-161
• /
• 2005

This paper proposes a speed-sensorless induction motor control system using a rotor speed compensation. To explain the proposed system, this paper describes an induction motor model in the synchronous reference frame for the vector control. The rotor flux is estimated by the rotor flux observer using the reduced-dimensional state estimator technique. The estimated rotor speed is directly obtained from the electrical frequency, the slip frequency, and the rotor speed compensation with the estimated q-axis rotor flux. The error of the rotor time constant is indirectly reflected in the rotor speed compensation using the compensation of the flux error angle. To precisely estimate the rotor flux, the actual value of the stator resistance, whose actual variation is reflected, is derived. An implementation of pulse-width modulation (PWM) pulses using an effective space vector modulation (SVM) is briefly mentioned. For fast calculation and improved performance of the proposed algorithm, all control functions are implemented in software using a digital signal processor (DSP) with its environmental circuits. Also, it is shown through experimental results that the proposed system gives good performance for the speed-sensorless induction motor control.

• ETRI Journal
• /
• v.20 no.2
• /
• pp.133-148
• /
• 1998

The objective of this paper is to present an adaptive algorithm for computing the weight vector which provides a beam pattern having its maximum gain along the direction of the mobile target signal source in the presence of interfering signals within a cell. The conjugate gradient method (CGM) is modified in such a way that the suboptimal weight vector is produced with the computational load of O(16N), which has been found to be small enough for the real-time processing of signals in most land mobile communications with the digital signal processor (DSP) off the shelf, where N denotes the number of antenna elements of the array. The adaptive procedure proposed in this paper is applied to code division multiple access (CDMA) mobile communication system to show its excellent performance in terms of signal to interference plus noise ratio (SINR), bit error rate (BER), and capacity, which are enhanced by about 7 dB, ${\frac{1}{100}}$ times, and 7 times, respectively, when the number of antenna elements is 6 and the processing gain is 20 dB.

• Proceedings of the KIEE Conference
• /
• 1995.11a
• /
• pp.268-270
• /
• 1995

In crane drives, DC motor has been most widely used due to simple control characteristic and favorable transient behavior. Nowadays, however, the squirrel cage induction motor is known as an attractive candidate due to elimination of all sliding electrical contacts, resulting in an exceedingly simple and rugged construction. Especially, in hoist application, the smooth torque control and four quadrant operation are essential. In this paper, an operation of dual inverters with common DC bus fed by vector controlled induction motor is described. Single DSP is employed as a main processor to control dual inverters and communicates each input/output signal with PLC. As well as giving a detailed expression, full simulation and experimental results are presented.

• Proceedings of the KIPE Conference
• /
• 2002.07a
• /
• pp.308-312
• /
• 2002

In this paper, EPLD(Erasable Programmable Logic Device) based induction motor drives with a SRP-PWM(Separatley Randomized Pulse Position PWM) is proposed. In the proposed RPWM (Random PWM), each of three phase pulses is located randomly in each switching interval. Based on the space vector modulation technique, the duty ratio of the pulses is calculated. To verify the validity of the proposed RPWM, the experimental study was tried. Along with the randomization of PWM pulses, the space vector modulation is also executed in the TMS320C31 DSP(Digital Signal Processor). The experimental results show that the voltage and switching noise harmonics are spread to a wide band area. Also, the performance of the proposed SRP-PWM and the conventional SVM-PWM are nearly the same from the viewpoing of the v/f constant control.

• Journal of Power Electronics
• /
• v.16 no.6
• /
• pp.2109-2118
• /
• 2016

Based on the space vector pulse width modulation (SVPWM) theory, this paper realizes an easier SVPWM strategy, which is equivalently implemented by CBSPWM with zero-sequence voltage injection. The traditional SVPWM strategy has no effect on controlling the neutral-point voltage balance. In order to solve the neutral-point voltage unbalance problem for neutral-point-clamped (NPC) three-level inverters, this paper proposes a neutral-point voltage balance controller. The proposed controller realizes controlling the neutral-point voltage balance by dynamically calculating the offset superimposed to the three-phase modulation waves of an equivalent SVPWM strategy. Compared with the traditional SVPWM strategy, the proposed neutral-point voltage balance controller has a strong ability to balance the neutral-point voltage, has good steady-state performance, improves the output waveforms quality and is easy for digital implementation. An experiment has been carried out on a NPC three-level inverter prototype based on a digital signal processor-complex programmable logic device (DSP-CPLD). The obtained experimental results verify the effectiveness of the proposed neutral-point voltage balance controller.

• Journal of the Korea Computer Graphics Society
• /
• v.16 no.4
• /
• pp.11-16
• /
• 2010

We present an efficient algorithm for rendering sweep surfaces using programmable graphics hardware. A sweep surface can be represented by a cross-section curve undergoing a spline motion. This representation has a simple matrix-vector multiplication structure that can easily be adapted to programmable graphics hardware. The data for the motion and cross-section curves are stored in texture memory. The vertex processor considers a pair of surface parameters as a vertex and evaluates its coordinates and normal vector with a single matrix multiplication. Using the GPU in this way is between 10 and 40 times as fast as CPU-based rendering.

• Journal of Sensor Science and Technology
• /
• v.22 no.4
• /
• pp.292-296
• /
• 2013

The ultrasonic wind sensor that pass through the air, beating the delivery of ultrasonic wind speed increases or decreases by the physical characteristics of the wind speed and the direction of the sensor, the transmission and reception of ultrasonic time difference measured by a two-axis vector wind and wind speed measured by calculating a device that converts the digital signal is Anemometer and wind direction meteorological facilities management, management of the ship sail used for various purposes, including, but used the existing 3-cup (mechanical) anemometer wind rotor caused by mechanical wear parts replacement due to the short-term, the reliability of the product is low, parts replacement, and according to the characteristics caused the car, there is a problem in high maintenance costs. In addition, because the bearings use of the marine environment and the cryogenic environment was constrained. In this study, the excellent long-term reliability, using ultrasonic-type environment that is not constrained to produce wind anemometer located $90^{\circ}$ conformal road using four piezoelectric sensors were fabricated structures, the piezoelectric oscillator circuit produces a rash and receiving transmit and receive speeds the car through the two-axis vector calculation to measure wind velocity processor firmware programming, and its characteristics were tested.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.31 no.4
• /
• pp.393-401
• /
• 1995

In this paper, vector analysis on the novel quick torque control of Induction Motors(I.M) based on voltage-controlled type is conducted. It was very difficult to get a step response of torque when the primary voltage was selected as control input of induction motors in conventional quick torque control methods. To solve this problem, the new control method was developed using a new concept of pulse addition which can realize the stepwise torque response of a specified settling time of $\Delta$. The new method was successfully confirmed through DSP(Digital Signal Processor) system-based experiments. However, it was a little difficult to understand the control mechanism intutionally. The purpose of this paper is to provide more understanding about the quick torque control mechanism using the vector analysis.