• Proceedings of the KIEE Conference
• /
• 2001.07c
• /
• pp.1732-1734
• /
• 2001

The purpose of this experiment was to develope Triggered Vacuum Switch(TVS) and to improve understanding of the high current vacuum arc phenomena in the TVS. The TVS has an array of rods of alternate polarity in which a fixed gap spacing is maintained between the rods. The cross section of each rod has trapezoidal shape. Breakdown of the TVS produced high current vacuum arc plasma. A spectroscopic measurement was performed over 20 kA peak current in the center of electrodes, in the vicinity of cathode, and outside electrodes. The electrode material tested was Fe. Measured Fe spectrum range was from 200 nm to 900 nm. Measurement result showed that over 90 percent of the charge states were FeII and the others were FeI and FeIII. The electron temperature was determined from the relative line intensity ratio methode of FeII system by assuming the local thermal equilibrium(LTE). The electron temperature at the center of electrodes was measured as 1.5 eV at 26 kA peak current. The electron temperature varied with its peak current. Intensity of spectrums is the highest in the vicinity of the cathode. Further we will also present study result of the diode phenomena in the TVS.

• Journal of Advanced Marine Engineering and Technology
• /
• v.28 no.3
• /
• pp.500-508
• /
• 2004

The heat transfer coefficients during gas cooling process of carbon dioxide in a horizontal tube were investigated. The experiments are conducted without oil in the refrigerant loop. The main components of the refrigerant loop are a receiver, a variable-speed pump, a mass flow meter, a pre-heater, and a gas cooler(test section). The water loop consists of a variable-speed pump, an isothermal tank, and a flow meter. The gas cooler is a counterflow heat exchanger by cooled water flowing in the annulus. The $CO_2$ flows in the horizontal stainless steel tube. which is 9.53mm in O.D. and 7.75mm in I.D. The gas cooler is 6 [m] in length. which is divided into 12 subsections, respectively. The experimental conditions considered in the study are following range of variables : refrigerant temperature is between 20 and $100^{\circ}C$. mass fluxes ranged from 200 to 400kg/($m^2$.s), average pressure varied from 7.5 to 10.0MPa. The main results were summarized as follows : The friction factors of $CO_2$ in the gas cooler show a relatively good agreement with those predicted by Blasius' correlation. The local heat transfer coefficient in the gas cooler has compared with most of correlations, which are the famous ones for forced convection heat transfer of turbulent flow. The results show that the local heat transfer coefficient of gas cooler agrees well with the correlation by Bringer-Smith except that at the region near pseudo critical temperature. while that at the near pseudo critical temperature is higher than the correlation.

• Journal of Advanced Marine Engineering and Technology
• /
• v.38 no.9
• /
• pp.1032-1038
• /
• 2014

In this study, an experimental study was performed to understand the boiling heat transfer characteristics of FC-72 in parallel micro-channels. The parallel micro-channels contained channels having a $0.2mm{\times}0.45mm$ [$H{\times}W$] cross section and length of 60 mm. And heat flux was varied from 16.4 to $25.6kW/m^2$ and mass fluxes from 300 to $500kg/m^2s$. The measured heat transfer coefficient was sharply decreased at lower vapor quality and then it was kept approximately constant as the vapor quality is increased. From the experimental results, the boiling heat transfer mechanism of FC-72 was confirmed and the measured heat transfer coefficient was compared and analyzed with the existing correlations to predict the heat transfer coefficient.

• Korean Journal of Head & Neck Oncology
• /
• v.12 no.2
• /
• pp.177-180
• /
• 1996

Warthin's tumor is a benign and slow growing tumor found exclusively in the parotid gland or the periparotid lymph nodes. It mostly affects males between the age of forty to seventy years and is closely related with smoking history. Between January 1981 and June 1996, 42 patients underwent surgical excision of Warthin's tumor of the parotid gland; which made up 10.6% of all parotid gland surgeries(398 cases) during the same period. Their ages ranged from 36 to 75 years with a mean age of 56 years. There were 33 male and 9 female patients with a 4.3 : 1 male to female ratio. The majority of the tumors were situated in the parotid tail whereas one was in the deep lobe. Bilateral simultaneous involvements of the parotid gland were found in 4 patients(9.5%) ; therefore total of 46 parotid glands were involved. Four(8.7%) of the 46 parotid glands had multifocal tumors ranginging from two to three lumps. Tumor sizes varied from 1.5 to 6.0cm with mean diameter of 3.lcm. Of the 42 patients, 26(61.9%) were diagnosed preoperatively or peroperatively by means of CT scans, ultrasound, 99m-Tc. scan, fine needle aspiration cytology or intraoperative frozen section biopsy. Of the 46 tumors, 30 underwent a superficial(n=29) or total(n=1) parotidectomy and for 16 cases with tumors suspected preoperatively or peroperatively of being single Warthin's tumor, only enucleation was performed. No cases of recurrence were identified during the follow up period regardless of type of operation performed, however the postoperative complication rate was much higher in the parotidectomy group(33.3%) than in the enucleation only group(12.5%). We feel that an enucleation procedure may be appropriate for the patients with single Warthin's tumor.

• Journal of the Korean Institute of Gas
• /
• v.15 no.4
• /
• pp.15-20
• /
• 2011

This study presents the behavior characteristics of buried three-layered pipeline subjected to pile driving loads corresponding to its cover depth. The analysis considered the driving energy caused by 7 tonf of ram weight and 1.2m of stroke with 20m distance from buried pipeline for all the analysis cases. A cover depth of pipe is varied 0.6m to 3.8m for this research. Vibration Velocity and stress are investigated at the center section in longitudinal direction. With same distance from pile, attenuation ratio of vibration velocity for increment of cover depth has shown an increasing trend. Also, Stress attenuation ratio of inner pipe is increased with cover depth.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.25 no.7
• /
• pp.1082-1088
• /
• 2001

Nowadays study on recycling disused plastics for automobiles was lively progressed. Rubber and talcum powder was added to retrieve degradation of physical properties caused by recycling disused polypropylene. The effect of the temperature, the fatigue load and the loading speed on DEN(double edged notch) specimen which was made by the pp-rubber composites during fracture was studied by. DEN specimen was made on PP-rubber composites through the injection molding. With increasing temperature the fracture strength was linearly decreased and the fracture energy was increased by $0^{\circ}C$ and after that decreased. In the same temperature the fracture strength during increasing the notch radius was hardly increased. The fracture behaviour at low and high loading speed was different entirely. At high loading speed plastic region was small and fracture behaviour was seen to brittle fracture tendency. With increasing fatigue load fracture energy was first rapidly decreased and subsequently steady when radius of notch tip was 2mm, but Maximum load during fracture scarcely varied. The deformation mechanism of polypropylene-rubber composites during fracture was studied by SEM fractography. A strong plastic deformation of the matrix ahead of the notch/crack occurred. The deformation seem to be enhanced by a thermal blunting of the notch/crack.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.30 no.6 s.249
• /
• pp.505-513
• /
• 2006

The pressure drop characteristics in a rotating two-pass duct with rib turbulators are investigated in the present study. Three ducts of different aspect ratios (W/H=0.5, 1.0 and 2.0) are employed with a fixed hydraulic diameter ($D_h$) of 26.7 mm. $90^{\circ}$-rib turbulators with $1.5mm{\times}1.5mm$ cross-section are attached on the leading and trailing surfaces. The pitch-to-rib height ratio (p/e) is 1.0. The distance between the tip of the divider and the outer wall of the duct is 1.0 W. The thickness of divider wall is 6.0 mm o. 0.225 $D_h$. The Reynolds number (Re) based on the hydraulic diameter is kept constant at 10,000 and the .elation number (Ro) is varied from 0.0 to 0.2. As duct aspect ratio increases, high friction factor ratios show in overall regions. The reason is that the rib height-to-duct height ratio (e/H) increases, but the divider wall thickness-to-duct width ($t_d/W$) decreases. The rotation of duct produces pressure drop discrepancy between the leading and trailing surfaces. However, the pressure drop discrepancy of the high duct aspect ratio (AR=2.0) is smaller than that of the low duct aspect ratio (AR=0.5) due to the decrement of duct hight (H).

• 보존과학연구
• /
• s.30
• /
• pp.203-215
• /
• 2009

In the conservation treatment of wood remains, polymers, treatment methods, and treatment period can be varied, depending on the percentage of moisture content and species of trees. Thus, in order to apply the appropriate conservation treatment, a lot of information from the wood remains are required. Despite the information from the wood remains, testing a part of the wood remains is necessary to get information about the polymers. When the wooden coffin made of camphor trees was excavated, it was cracked in the section of radiation, and there were hairlines cracks. Therefore, without any conservation treatment, it is impossible to restore it. This experiment is for the conservation treatment of the wooden coffin excavated from Songhyun-dong tombs No 7, Changnyeong. For this experiment, I used camphor trees from Jejudo. The purpose of this experiment is to asses the possibility of preliminary testing materials before the conservation treatment on the wooden coffin. After the camphor trees from Jejudo are artificially aged by Fenton's reagent, they are As a result of oxidation by Fenton, the degree of oxidation is high in proportion to the amount of peroxide and iron sulfate. Among several samples, the sample 'na' made the most similar result to the wooden coffin from Songhyun-dong. If I use this condition to make the sample in polymer tests, it is very helpful to find the most suitable polymer for the conservation treatment of wooden coffin. After the same species of trees are oxidized by Fenton and they become the similar condition, we are able to find suitable methods of conservation treatment. The suitable methods reduce the demage of the remains and make us to get more information. Thus, we are able to carry out conservation treatment more exactly.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.3
• /
• pp.1272-1278
• /
• 2014

In this experimental study for the current growing offshore wind, a wind tunnel test was conducted to examine the performance of the vertical-type cross-flow wind turbine power generation system. Due to the limited size of the test section of the wind tunnel, the inlet guide vane of the original wind power generation was scaled down to about 1/5 and the turbine impeller diameter was also reduced to 1/2 of the prototype impeller. The number of the impeller blade is another important parameter to the output power of the wind power generation system and the number was varied 8 and 16. From the analysis of the experimental result, the output brake power of the model wind turbine was measured as 278watts with the 16-blade at 12 m/s of the rated wind speed and the rated brake power of the prototype wind turbine is calculated to 3.9kW at the rated operating condition.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.3
• /
• pp.405-412
• /
• 2013

This paper reports the steady-state stresses within the heat affected zone (HAZ) of a welded straight pipe subject to creep. The creep constants and exponent are varied systematically to see the effect of various mismatches in creep properties on the steady-state creep stresses, via detailed two-dimensional finite element (FE) creep analyses. The weldments consist of the base metal and weld metal with the HAZ, which are characterized using the idealized power creep laws with the same creep exponent. The internal pressure and axial loading are considered to see the effect of the loading mode. To quantify the creep stresses, a creep mismatch factor is introduced as a function of the creep constants and exponent. It is concluded that the ratio of the section-averaged stresses for a mismatched case to those for an evenmatched case are linearly dependent on the mismatch factor. The results are compared with the FE results, including the Type IV region, as well as the R5 procedure.