• The Journal of Korean Academy of Prosthodontics
• /
• v.31 no.3
• /
• pp.423-446
• /
• 1993

Titanium and its alloys are finding increasing use in medical devices and dental implants. The strong selling point of titanium is its resistance to the highly corrosive body fluids in which an implant must survive. This corrosion resistance is due to a tenacious passive oxide or film which exists on the metal's surface and renders it passive. Potentiodynamic polarization measurement is one of the most commonly used electro-chemical methods that have been applied to measure corrosion rates. And the potentiodynamic polarization test supplies detailed information such as open circuit, rupture, and passivation potential. Furthermore, it indicates the passive range and sensitivity to pitting corrosion. This study was designed to compare the corrosion resistance of the commonly used dental implant materials such as CP Ti, Ti-6A1-4V, Co-Cr-Mo alloy, and 316L stainless steel. And the effects of galvanic couples between titanium and the dental alloys were assessed for their useful-ness-as. materials for superstructure. The working electrode is the specimen , the reference electrode is a saturated calomel electrode (SCE), and the counter electrode is made of carbon. In $N_2-saturated$ 0.9% NaCl solutions, the potential scanning was performed starting from -800mV (SCE) and the scan rate was 1 mV/sec. At least three different polarization measurements were carried out for each material on separate specimen. The galvanic corrosion measurements were conducted in the zero-shunt ammeter with an implant supraconstruction surface ratio of 1:1. The contact current density was recorded over a 24-hour period. The results were as follows : 1. In potential-time curve, all specimens became increasingly more noble after immersion in the test solution and reached between -70mV and 50mV (SCE) respectively after 12 hours. 2. The Ti and Ti alloy in the saline solution were most resistant to corrosion. They showed the typical passive behavior which was exhibited over the entire experimental range. Therefore no breakdown potentials were observed. 3. Comparing the rupture potentials, Ti and Ti alloy had the high(:st value (because their break-down potentials were not observed in this study potential range ) followed by Co-Cr-Mo alloy and stainless steel (316L). So , the corrosion resistance of titanium was cecellent, Co-Cr-Mo alloy slightly inferior and stainless steel (316L) much less. 4. The contact current density sinks faster than any other galvanic couple in the case of Ti/gold alloy. 5. Ag-Pd alloy coupled with Ti yielded high current density in the early stage. Furthermore, Ti became anodic. 6. Ti/Ni-Cr alloy showed a relatively high galvanic current and a tendency to increase.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.13 no.3
• /
• pp.219-225
• /
• 2020

With the aging population, the prevalence of musculoskeletal disorders in the elderly continues to increase. In addition, musculoskeletal disorders are the third most common social and economic loss among occupational illnesses in Workers' compensation insurance benefits as of 2015 standard and are also common among workers. In this study, a vest that can assist in the prevention and treatment of musculoskeletal disorders of the waist was produced, and it is intended to confirm the presence or absence of the effect through experiments. Diseases of the waist are closely related to core muscles. Therefore, the produced vest was made in a form that supports the core muscles. Before and after wearing the vest for effectiveness verification, the While performing 10-times of the Mackenzie exercises, a waist extension exercise, collected the EMG data of the internal oblique, Rectus abdominis, and Erector spinae, which correspond to the core muscles. The collected data were analyzed through the electromyography analysis program RM-3 to obtain RMS values for 10-times measurements of each muscle and to compare the average values. After comparing the data, to verify the significance, the technical statistical value of the measurement result was calculated and the average difference was verified through PASW ver18.0, And the paired t-test is performed on the experimental results to perform statistical processing. and Statistical processing was performed by setting the significance level to α=.05.

• Journal of the Korean Society of Safety
• /
• v.31 no.3
• /
• pp.8-15
• /
• 2016

The purpose of this study is to design a model with the structural stability so as not to lose the operational function due to structural plastic or fail of a sliding blast door by blast pressure to this aim, a numerical simulation was performed using full-size experiments and M&S (Modeling & Simulation) of the sliding blast door. The sliding blast door ($W3,000{\times}H2,500mm$) under the blast load is in the form of a sliding type 2-way metal grill, which was applied by a design blast pressure (reflected pressure $P_r$) of 17 bar. According to the experimental results of a real sliding blast door under blast load, the blast pressure reached the sliding blast door approximately 4.3 ms after the explosion and lasted about 4.0 ms thereafter. The maximum blast pressure($P_r$) was 347.7 psi (2,397.3 kPa), it is similar to the UFC 3-340-02 of Parameter(91 %). In addition, operation inspection that was conducted for the sliding blast door after real test showed a problem of losing the door opening function, which was because of the fail of the Reversal Bolt that was installed to prevent the shock due to rebound of the blast door from the blast pressure. According to the reproduction of the experiment through M&S by applying the blast pressure measurement value of the full-size experiments, the sliding blast door showed a similar result to the full-size experiment in that the reversal bolt part failed to lose the function. In addition, as the pressure is concentrated on the failed reversal bolt, the Principal Tensile Failure Stress was exceeded in only 1.25 ms after the explosion, and the reversal bolt completely failed after 5.4 ms. Based on the result of the failed reversal bolt through the full-size experiment and M&S, the shape and size of the bolts were changed to re-design the M&S and re-analyze the sliding blast door. According to the M&S re-analysis result when the reversal bolt was designed in a square of 25 mm ($625mm^2$), the maximum pressure that the reversal bolt receives showed 81% of the principal tensile failure stress of the material, in plastic stage before fail.

• Journal of Navigation and Port Research
• /
• v.39 no.4
• /
• pp.299-305
• /
• 2015

Modbus is a serial communications protocol, it has since become a practically standard communication protocol, and it is now a commonly available means of connecting industrial electronic devices. Therefore, it can be connected with all devices using Modbus protocol to the measurement and remote control on the ships, buildings, trains, airplanes and etc.. In this paper, we add the Modbus communication protocol to the existing lighting controller sensitivity to enable verification and remote control by external environmental factors, and also introduces a fuzzy inference system was configured by external environmental factors to control LED lighting. External environmental factors of temperature, humidity, illuminance value represented by the LED through a fuzzy control algorithm, the values accepted by the controller through the sensor. Modbus is using the RS485 Serial communication with other devices connected to the temperature, humidity, illumination and LED output status check is possible. In addition, the remote user is changed to enable it is possible to change the RGB values in the desired color change. Produced was confirmed that the LED controller output is based on the temperature, humidity and illumination.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.14 no.1
• /
• pp.51-64
• /
• 2002

To investigate long-period wave responses in Sokcho Harbor and Cheongcho lagoon, field measurements were made for long-and short-period waves and current velocities using a Directional Waverider, a ultrasonic-type wave gauge, four pressure-type wave gauges, and a current meter. From the data analysis, it was found that the Helmholtz resonant periods of Sokcho Harbor and Cheongcho lagoon are about 13.6 and 54.5 minutes, respectively, and the dominant period of wave induced current in the passage between Sokcho Harbor and Cheongcho lagoon is about 55.2 minutes which depends on Helmholtz resonant condition of the Cheongcho lagoon. It was also found that the energy level of the far-infra-gravity waves during storm conditions is very high compared with that during calm sea conditions. To investigate relationships between far-infra-gravity waves and short-period waves at offshore station, regression analyses were carried out especially for 1) heights, 2) periods, 3) direction and height, 4) height and period between short-and far-infra-gravity waves, respectively. The results showed that the long-period wave height is highly correlated with the short-period wave height. However, no special trend was found for the other relations. In the future far-infra-gravity wave heights on return period around Sokcho Harbor region can be suggested by using extreme value analyses of long term measured data.

• Archives of design research
• /
• v.12 no.4
• /
• pp.171-179
• /
• 1999

Originally the COS system was developed based on fashion colors. But in interiors many other color groups are used frequently, so the COS system is somewhat insufficient for interior design work. The purpose of this study is to verify the pratical use of the COS system in finishing colors of housing interiors and to propose the additional colors based on interior finishings. The COS system and the NCS color system were used for color measurement. The results was as follows. In the hues, Y.YR.GY.PB.B.BG color groups were used for interior material more frequently. And regardless of hues, low saturation and high value colors were used. Most of the colors were inscribed as the COS system and the NCS color system simultaneouly, but muted and grayed color tones like pale.light.grayish.soft cannot be founded in the COS system. Therefore more subdued and soothing tones of Y.YR.GY.PB.B.BG color groups should be added to the COS system.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.6
• /
• pp.4125-4130
• /
• 2015

This paper presents the communication performance for the radiation pattern reconfigurable antenna in the wearable device measuring bio signal (temperature, blood pressure, pulse etc.) of human body. The operational frequency is 2.4 - 2.5 GHz, which covers Bluetooth communication bandwidth. The maximum gain of the antennas is 1.96 dBi. The proposed antenna is efficiently transmitting and receiving signal by generating two opposite beam directions using two RF switches (PIN diode). Also, we investigated how radiation pattern changes according to three angles ($30^{\circ}$, $90^{\circ}$, $150^{\circ}$) of Top Loading. In this paper, we measured and compared the SNR (Signal-to-Noise Ratio) and BER (Bit Error Rate) performances of the proposed antennas in the condition between an ideal environment of anechoic chamber and smart house existing practical electromagnetic interferences (Universal Software Radio Peripheral, USRP). Throughout the comparing the results of the measurement of two cases, we found that the SNR is degraded over 5dB in average and BER is increased over ten times in maximum, therefore, it is confirmed that the error rate of receiving signal is increased. The measured results of SNR and BER value in this paper able to expect the performance degrading by the interference from the electromagnetic devices.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.7
• /
• pp.2541-2548
• /
• 2010

This paper describes the calculation for characteristic impedance of transmission line with periodic structures such as defected ground structure (DGS) and photonic bandgap (PBG). The previous method which uses the ${\lambda}$/4 transmission line model is reviewed and its disadvantage that the calculated characteristic impedance is strongly dependent on the frequency is discussed. The characteristic impedance of transmission lines with periodic structures are calculated using the ${\lambda}$/4 transmission line model and analytic method. The calculated characteristic impedance by the latter method is an almost constant value while that from the first method depends on the frequency strongly. In addition, the characteristic impedance of the transmission line with PBG is calculated and proposed, while it has been rarely studied ever. S-parameters are obtained from the measurement using the fabricated sample as well as simulation, and used for calculating the characteristic impedances and comparison. The characteristic impedances calculated from the measured S-parameters agree well with the simulated results. It is well described that the analytic method to calculate the characteristic impedance of transmission lines on uniform dielectric structures can be applied successfully to the transmission lines with periodic structures such as DGS and PBG.

• Korean Journal of Remote Sensing
• /
• v.30 no.5
• /
• pp.627-639
• /
• 2014

Accurate correction of surface effect from back scattered solar radiance is one of key issue to retrieve aerosol information from satellite measurements. In this study, two different methods are applied to retrieve surface reflectance by using single visible channel measurement from meteorological imager onboard COMS. The first one is minimum reflectance method, which composes the minimum value among previously measured reflectances at each pixel over a certain search window length. This method assumes that the darkest pixel corresponds to the aerosol-free condition, and deduces surface reflectance by correcting atmospheric scattering from the measured visible reflectance. The second method, named as the "atmospheric correction method" in this study, estimates the result by correcting aerosol and atmospheric scattering with ground-based observation of aerosol optical properties. The purpose of this study is to investigate the retrieval accuracy of the widelyused minimum reflectance method. Also, the retrieval error caused by the loading of background aerosol is mainly estimated. The comparison between surface reflectances retrieved from the two methods shows good agreement with the correlation coefficient of 0.87. However, the results from the minimum reflectance method are slightly overestimated than the values from the atmospheric correction method when surface reflectance is lower than 0.2. The average difference between the two results is 0.012 without the background aerosol correction. By considering the background aerosol effect, however, the difference is reduced to 0.010.

• Korean Security Journal
• /
• no.61
• /
• pp.235-254
• /
• 2019

This study identifies a factor structure regarding the criterion of terror awareness by using confirmatory factor analysis. The study provides information whether the criterion fits in the analysis of terror awareness in Korea or not. Data of 176 public officials working at the National Assembly collected in 「Study on the Improvement of Security in the National Assembly Building」(Choi O-Ho and others, 2016) was used in the analysis. Study results showed the fit statistics of 3 questions regarding concern in terror, 5 questions regarding cognition of terror occurrence, 3 questions regarding countermeasure of terror, and 3 questions regarding equipments against terror satisfied the standard. Also, standard regression coefficient exceeded the standard and was shown to be fit. Concern in terror, as a latent variable, was below the standard value of average variance extracted. However, focused validity was secured by obtaining other values fit. This study proceeded distinct validation test to supplement data. The test results showed that the criterion level was fit. Thus, further survey should include questions that are appropriate to measure the awareness of terror based not only on theories and previous studies but also on questions of terror awareness tested in this study. Such development in surveys will support the means of data measurement.