• 한국태양에너지학회 논문집
• /
• 제23권2호
• /
• pp.81-90
• /
• 2003

UTAC(unglazed transpired air collector) system has unique advantage for space heating and tempering ventilation air over the conventional collector system such as flat plate and vacuum collector. UTAC can improve radiative and convective loss due to nonglazed component and enhanced plate surface configuration. and heating energy and its equivalent green house emission performance can be improved from the use of this like collector in building application. The Option D Calibration simulation approach of IPMVP(International Performance Measurement and Verification Protocol) in ESCO businesses has been recommended to use of the calibrated computer modules like these Energy-10. DOE2.1E and TRNSYS(transient system simulation). This study is to develop subroutine type-203 of TRNSYS15.2 program and appraise thermal performance of UTAC. With newely addeded subroutine type-203. 1) Thermal performance of unglazed transpired collector could be possible based on dimensionless variables such as efficiency and heat exchanger effectiveness. and 2) Assessement of energy consists of solar useful and insulation saving for UTAC could be possible.

• 조명전기설비학회논문지
• /
• 제28권7호
• /
• pp.41-47
• /
• 2014

The on-line partial discharge (PD) in stator windings of air-cooled gas turbine (GT) generator (119.2MVA, 13.8kV) is measured and analyzed in this paper. This generator was designed by global vacuum pressure impregnation (VPI). The generator failed two times at top bar (16T) of phase B in the stator slot. Six epoxy-mica capacitors were installed in three phases of GT generator. On-line PD test was performed on GT generator using turbine generator analyzer (TGA). TGA showed that the normalized quantity number (NQN) and the PD magnitude($Q_m$) were high in phase B. Internal discharges were generated in phases A, B and C. The trend analysis of NQN and $Q_m$ value are obtained in order to monitor the insulation condition in GT generator stator windings. Phases A and C were in good condition. But phase B had deteriorated significantly

• Applied Science and Convergence Technology
• /
• 제26권6호
• /
• pp.208-213
• /
• 2017

Flexible opto-electronic devices are developed on the insulating layer deposited stainless steel (STS) substrates. The silicon dioxide ($SiO_2$) material as the diffusion barrier of Fe and Cr atoms in addition to the electrical insulation between the electronic device and STS is processed using the plasma enhanced chemical vapor deposition method. Noble silver (Ag) films of approximately 100 nm thickness have been formed on $SiO_2$ deposited STS substrates by E-beam evaporation technique. The films then were annealed at $650^{\circ}C$ for 20 min using the rapid thermal annealing (RTA) technique. It was investigated the variation of the surface morphology due to the interaction between Ag films and $SiO_2$ layers after the RTA treatment. The results showed the movement of Si atoms in silver film from $SiO_2$. In addition, the structural investigation of Ag annealed at $650^{\circ}C$ indicated that the Ag film has the material property of p-type semiconductor and the bandgap of approximately 1 eV. Also, the films annealed at $650^{\circ}C$ showed reflection with sinusoidal oscillations due to optical interference of multiple reflections originated from films and substrate surfaces. Such changes can be attributed to both formation of $SiO_2$ on Ag film surface and agglomeration of silver film between particles due to annealing.

• 한국태양에너지학회 논문집
• /
• 제35권1호
• /
• pp.89-96
• /
• 2015

n-octadecnae based shape stabilized phase change material (SSPCM) was prepared by using vacuum impregnation method. And an exfoliated graphite nanoplate (xGnP) which has high thermal conductivity properties is used as a PCM container. And then we made heat storage concretes which contains SSPCM for reducing heating and cooling load in buildings. In the prepararion process, the SSPCM was mixed to a concrete as 10, 20 and 30wt% of cement weight. The thermal properties and chemical properties of heat storage concrete were analyzed from Scanning electron microscope (SEM), Fourier transformation infrared spectrophotometer (FT-IR), Deferential scanning calorimeter (DSC), Thermogravimetric analysis (TGA) and TCi thermal conductivity analyzer. And we conducted surface temperature analysis of SSPCM and xGnP by using heat plate and insulation mold.

• 한국초전도ㆍ저온공학회논문지
• /
• 제22권4호
• /
• pp.14-19
• /
• 2020

Here we present the comparative experimental study of the stability of the superconducting state in 4 mm YBCO tapes with copper lamination against local heat disturbances at 77 K. The samples are either directly cooled by immersing a bare YBCO tape into a liquid nitrogen pool or operate in nearly-adiabatic conditions when the tape is covered by a 0.6 mm layer of Kapton insulation. Main quench characteristics, i.e. minimum quench energies (MQEs) and normal zone propagation (NZP) velocities for both samples are measured and compared. Minimum NZP currents are determined by a low ohmic resistor technique eligible for obtaining V - I curves with a negative differential resistance. The region of transport currents satisfying the stationary stability criterion is found for the different cooling conditions. Finally, we use the critical temperature margin as a universal scaling parameter to compare the MQEs obtained in this work for YBCO tapes at 77 K with those taken from literature for low-temperature superconductors in vacuum at 4.2 K, as well as for MgB2 wires cooled with a cryocooler down to 20 K.

• Tribology and Lubricants
• /
• 제37권6호
• /
• pp.203-207
• /
• 2021

This study presents the development of dielectric constant sensors to measure lubricant properties. The lubricant oil sensor is used to measure oil properties and machine conditions. Various condition monitoring methods are applied to diagnose machine conditions. Machine condition monitoring using oil sensors has advantage over other machine condition monitoring methods. The fault conditions can be noticed at the early stages by the detection of wear particles using oil sensors. Therefore, it provides an early warning in the failure procedure. A variety of oil sensors are applied to check the machine condition. Among all oil sensors, only one sensor can measure the tendency of several properties such as acidity and water content. A dielectric constant sensor is also used to measure various oil properties; therefore, it is very useful. The dielectric constant is the ratio of the capacitance of a capacitor using that material as a dielectric to that of a similar capacitor using vacuum as its dielectric. The dielectric constant has an effect on water content, contaminants, base oil, additive, and so forth. In this study, the dielectric constant sensor is fabricated using MEMS process. In the fabrication process, the shape, gap of the electrode array, and thickness of the insulation material are considered to improve the sensitivity of the sensor.

• 한국수소및신에너지학회논문집
• /
• 제9권4호
• /
• pp.169-176
• /
• 1998

Ni/MH 2차전지의 음극용 금속간화합물전극의 부식특성에 미치는 합금원소와 결합제의 영향을 조사하였다. 전극의 재료는 $(LM)Ni_{4.49}Co_{0.1}Mn_{0.205}Al_{0.205}$와 $(LM)Ni_{3.6}Co_{0.7}Mn_{0.3}Al_{0.4}$의 $AB_5$ type합금을 모재로 하였다. 여기에 Si sealant 또는 PTFE를 결합제로 첨가한 것과 원재료 분말에 구리를 20% 무전해도금한 것을 냉간 압착하여 전극을 제조하였다. 부식특성을 조사하기위해 탈공기된 6M의 KOH 용액에서 동전위법과 순환전위법을 이용하여 부식전류와 전류밀도를 측정하였다. 모재에 Co가 많이 함유되면 전극의 내식성을 향상시키고 Ni이 많이 함유되면 충전과 방전을 반복하는 동안에 전극의 안정성을 저하시켰다. 부식전류밀도는 Si sealant를 결합제로 사용한 전극의 경우가 PTFE를 사용한 전극의 경우보다 낮았고 Cu가 도금된 전극은 내식성에서 가장 우수하게 나타났다.

• 한국진공학회지
• /
• 제22권3호
• /
• pp.131-137
• /
• 2013

본 연구에서는 유기소자의 절연박막을 습식 공정이 아닌 건식 공정인 플라즈마 중합법을 이용하여 Styrene 유기물을 사용하여 절연박막을 제작하였다. 안정적인 플라즈마 형성을 위해 버블러와 써큐레이터를 활용하여 정량적인 모노머 주입을 가능하게 하였다. 본 연구에서는 플라즈마 중합된 Styrene 박막을 30, 60 nm 터널링층으로 활용하였고, Styrene 절연층의 두께를 430 nm, Au 메모리층의 두께를 7 nm, 활성층의 두께를 40 nm, 소스와 드레인 전극의 두께를 50 nm로 유기 메모리 소자를 제작하여 특성을 평가하였다. 40/-40 V의 double sweep시 45 V의 히스테리시스 전압을 얻을 수 있었고, 이는 MMA를 터널링층으로 활용한 유기 메모리 소자의 히스테리시스 전압이 27 V인 것과 비교하였을 때 60% 상승한 효과로 히스테리시스 전압이 18 V 이상 높은 결과이다. 이와 같은 결과로부터 플라즈마 중합된 Styrene 유기 박막의 높은 전하 포집 특성을 활용하여 전체층을 유기 재료로 제작한 유연한 메모리 소자의 응용 가능성을 기대한다.

• 한국진공학회지
• /
• 제16권2호
• /
• pp.153-159
• /
• 2007

KSTAR 장치의 저온 component에 헬륨을 공급하기 위한 헬륨라인은 크게 두 가지로 이루어져 있다. 냉동기에서 KSTAR 저온용기 외부까지의 트랜스퍼 라인과, 저온용기 내부의 헬륨라인이다. KSTAR 장치는 3가지 종류의 헬륨을 사용하여 각 저온 component를 냉각하는데, 초전도 자석 시스템과 버스라인에는 초임계 헬륨, 전류인입장치에는 액체 헬륨, 열차폐체에는 가스 헬륨을 공급한다. 저온용기 내부의 헬륨라인은 냉동기에서 저온용기 근처까지 연결된 배관을 저온용기 내부의 각 장치에 최단거리로 열손실 없이 설치하여 각 장치가 정상 작동하도록 하는데 그 목적이 있다. 저온용기 내부의 헬륨라인은 최대 20bar로 가압되는 운전시간 동안에 헬륨누설 없이 설치되어야 한다. 그리고 상온으로 부터의 복사열을 차단하기 위하여 다층절연제로 배관을 감싸주어야 하고 고전압 부분은 프리프레그 테잎으로 절연되어야 한다. 전기절연체는 세라믹과 스테인레스 스틸 튜브를 브레이징 접합 방법으로 연결하여 만들어진 것으론 배관과 배관, 배관과 저온 component간의 절연을 위해 사용되고, 헬륨라인과 동일하게 4.5K 초임계 헬륨온도에서 누설이 없어야 한다. 따라서 모든 전기절연체는 액체질소에 침전시켜 열충격을 가하고, 내부에 30 bar를 가압하여 진공 누설시험을 한다. 그리고 초전도 자석과 배관의 절연체로 사용되므로 15kV 고전압 절연 검사를 한다. 전기절연체의 세라믹 부분은 구조적 보강을 위하여 추가적으로 표면에 절연 작업을 한다. 현재 대부분의 저온용기 내부의 헬륨 라인은 설치 완료되어 있으며, 최종 검사가 진행 중이다.

• 한국재료학회지
• /
• 제22권6호
• /
• pp.309-315
• /
• 2012

Metal foam has many excellent properties, such as light weight, incombustibility, good thermal insulation, sound absorption, energy absorption, and environmental friendliness. It has two types of macrostructure, a closed-cell foam with sealed pores and an open-cell foam with open pores. The open-cell foam has a complex macrostructure consisting of an interconnected network. It can be exploited as a degradable biomaterial and a heat exchanger material. In this paper, open cell Mg alloy foams have been produced by infiltrating molten Mg alloy into porous pre-forms, where granules facilitate porous material. The granules have suitable strength and excellent thermal stability. They are also inexpensive and easily move out from open-cell foamed Mg-Al alloy materials. When the melt casting process used an inert gas, the molten magnesium igniting is resolved easily. The effects of the preheating temperature of the filler particle mould, negative pressure, and granule size on the fluidity of the open cell Mg alloy foam were investigated. With the increased infiltration pressure, preheat temperature and granule sizes during casting process, the molten AZ31 alloy was high fluidity. The optimum casting temperature, preheating temperature of the filler particle mould, and negative pressure were $750^{\circ}C$, $400-500^{\circ}C$, and 5000-6000 Pa, respectively, At these conditions the AZ31 alloy had good fluidity and castability with the longest infiltration length, fewer defects, and a uniform pore structure.