• Journal of Hydrogen and New Energy
• /
• v.1 no.1
• /
• pp.15-23
• /
• 1989

The selective separation of hydrogen from gas mixture containing hydrogen was experimentally studied using $LaNi_5$. The capacity and the rate of hydrogen separation, the purity of recovered hydrogen and the optimum condition of the regeneration of deactivated $LaNi_5$ were investigated. The separation rate and the recovery ratio of hydrogen were slowly decreased with the increase of the number of hydrogen absorption cycle. It was found that this result comes from the deactivation of $LaNi_5$ partly because of the blocking of hydrocarbon compounds in the $LaNi_5$ lattice and partly because of the poisoning of $LaNi_5$ surface by carbon monoxide contained in the gas mixture. The optimum condition for the regeneration of deactivated $LaNi_5$ was obtained by heating in a vacuum to about 637 K. The recovery ratio of hydrogen at the optimum condition was observed to be about 80%. The rates of hydrogen separation were measured in the ${\alpha}$-phase and two phase regions. The rate equations could be expressed as follows ; ${\alpha}$ - phase : $$-\frac{dP{_{H_2}}}{dt}=9.836{\times}10^{-3}(P{_{H_2}}_{-P_{eq}})$$ two phase region : $$-\frac{dP_{H{_2}}}{dt}=1.6909{\times}10^2\exp(-17560/RT)(P{_{H_2}}_{-P_{eq}})$$.

• Journal of Welding and Joining
• /
• v.31 no.3
• /
• pp.76-83
• /
• 2013

This study investigated the effect of bonding temperature and holding time on microstructures and mechanical properties of diffusion bonded joint of Haynes230. The diffusion bonds were performed at the temperature of 950, 1050, and $1150^{\circ}C$ for holding times of 30, 60, 120 and 240 minutes at a pressure of 4MPa under high vacuum condition. The amount of non-bonded area and void observed in the bonded interface decreased with increasing bonding temperature and holding time. Cr-rich precipitates at the linear interface region restrained grain migration at $950^{\circ}C$ and $1050^{\circ}C$. However, the grain migration was observed in spite of short holding time due to the dissolution of precipitates to base metal in the interface region at $1150^{\circ}C$. Three types of the fracture surface were observed after tensile test. The region where the coalesce and migration of grain occurred much showed high fracture load because of base metal fracture whereas the region where those did less due to the precipitates demonstrated low fracture load because of interface fracture. The expected fracture load could be derived with the value of fracture area of base metal ($A_{BF}$) and interface ($A_{IF}$), $Load=201A_{BF}+153A_{IF}$. Based on this equation, strength of base metal and interface fracture were calculated as 201MPa and 153MPa, respectively.

• Preventive Nutrition and Food Science
• /
• v.3 no.4
• /
• pp.374-378
• /
• 1998

The objectives of this study are to determine the optimum process conditions of Korean beeswax and discuss the parameter of adsorption . Purification conditions, such as time, temperature and the type of adsorbents were investigated using the relationship between the properties of refined products and process conditions and theiptimum bleaching condition of Korean beeswax were determined for the first time. The various bleaching conditions were examined by observing the result of Lovibond color, photometric color, methods provided by the American Oil Chemists '(A.O.C.S).The iptimum bleaching temperature was 8$0^{\circ}C$ and the bleaching agents (5% of the weight of beeswax) which consisted of activated clay and activated carbon and a vacuum system were also necessary.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.657-659
• /
• 2004

Trivalent cerium ($Ce^{3+}$) activated yttrium aluminum garnet ($Y_3Al_5O_{12}$, YAG) phosphor thin films were deposited on quartz glass substrates by rf magnetron sputtering. The effects of sputtering parameters and annealing condition on the luminescent properties were investigated. The sputtering parameters were $O_2$/Ar gas ratio, rf power, and deposition time. The films were annealed at 1200 $^{\circ}C$ for 5 hours in $N_2+$vacuum atmosphere. Polycrystalline YAG:Ce thin film phosphor could be obtained with a gas ratio of $O_2$/(Ar+$O_2$)=0.5 after post-annealing. PL spectra excited at 450 nm showed a yellow single band at 550 nm.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.1046-1048
• /
• 2004

Performances of organic thin film transistors (OTFTs) can be detrimentally affected by the state of the gate dielectric. Because of the bad stability of polymers, OTFTs with polymer gate dielectrics often provide abnormal characteristics. In this study, we report the condensation effect of the polymer gate dielectric layer. For the observations of the effect of the condensation, the spin-coated polymer layers with various deposition conditions were fabricated and left under low vacuum condition for several days. It is observed that the thickness of polymer layer and the electrical characteristic of OTFTs vary with the condensation time.

• 전자공학회논문지 IE
• /
• v.44 no.3
• /
• pp.1-5
• /
• 2007

A new field emission tip array was realized by Ti silicidation of Ti coated Si tip, which has long term durability, chemical stability, and high emission current density. The fabricated Ti silicided FE tip array under high vacuum condition of about $10^{-8}Torr$ shows that the turn-on voltage is about 40V and the emission current is about $69{\mu}A$ when the bias of 150V is applied between anode and cathode of $100{\mu}m$ distance.

• Proceedings of the Optical Society of Korea Conference
• /
• 1990.02a
• /
• pp.162-166
• /
• 1990

Photoinduced anisotropy (PIA) in amorphous As2S3 (a-As2S3 ) thin film, deposited by vacuum evaporation, is investigated. PIA is induced by linearly polarized Ar+ laser beam (λ=514.5nm) and probed by weak Ar+ laser (λ=514.5nm) and He-Ne laser (λ=632.8nm) beam through the crossed analyzer. Keeping pump beam intensity constantly, rotation of pump beam polarization direction induces reorientation phenomina of anisotropic axis. Introducing directional factor into simplified 3-level system, which is used to analyze photodarkening phenomina, an analytical expression of PIA is derived. Temporal behavior of PIAand its reorientation phenomina are investigated andcompared with theory. In the experiment pump beam intensity is 100mW/$\textrm{cm}^2$ and thickness of a-As2S3 thin film is 3${\mu}{\textrm}{m}$. In those condition, time constant of photoinduced anisotropy obtained by method of least square curve fitting is 4.0$\times$10-2sec-1. The time constant of PIA we obtained is larger than that of photodarkening, 2.8$\times$10-2sec-1.

• KSBB Journal
• /
• v.14 no.5
• /
• pp.561-565
• /
• 1999

Optimum conditions for vacuum-drying ad cultivation of yeast cells for the production of active dry yeast were examined. At lower temperature, more drying time was required to dry the yeast pellet to reach the desirable water content(8%). Optimum temperature of vaccum oven and time for drying was 63$^{\circ}C$ and 90 min, respectively. Optimum medium composition for flask culture using cane molasses as the substrate were 0.25% sugar, 0.013% $K_2$HPO$_4$, 0.1% $K_2$HPO$_4$. and 0.125% (NH$_4$)$_2$SO$_4$. Culture temperature $25^{\circ}C$ gave the highest survival rate of dired yeast. After finishing fed-batch culture and the culture was left in the fermentor without adding any sugar or nutrient, survival of the dried yeast harvested from the fermentor increased to 86.0% after 36 hr. It was also observed that the yeast cells with higher budding rates showed lower survival rate.

• Journal of Welding and Joining
• /
• v.21 no.4
• /
• pp.69-74
• /
• 2003

The mechanical properties of STD11 Joints by using TLP (Transient Liquid Phase Diffusion) bonding method employing MBF-30 and MBF-80 insert metals were investigated with concerning to the microstructural change. TLP bonding of STD 11 was carried out at 1323∼1423K for 0.6ks∼3.6ks in vacuum. The microstructure and the element distribution of the interlayer between tool steels and insert metals showed specific feature with bonding conditions. It was found that the width of the interlayer increased at initial bonding stage. However, the width of interlayer showed nearly constant value during the isothermal solidification. After isothermal solidification was completed, the joint showed homogeneous element distribution and similar microstructure with base metal because of the grain boundary migration to the bonded interlayer. The bonding strength measured by a tensile test has been varied with the bonding conditions. The maximum joint strength, 760MPa, was obtained with the condition of 1423K for 1.2ks using MBF30 insert metal in this experiment.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.27 no.5
• /
• pp.312-316
• /
• 2014

Photoemission is a process in which photons are converted into free electrons. Photocathodes are the typical materials for the process. They emit electrons when a light is irradiated upon. The traditional method of manufacturing photocathodes is complicated, requires specialized equipment, and is limited very small sized samples. $Cs_3Sb$ photocathode was formed on a substrate in $N_2$ atmospheric conditions. The photocathode formation was a gas phase reaction with the substrate. Vacuum devices were made to test electron emission characteristics of the formed photocathode. Visible light of wavelength 475 nm was used for the primary light source. The results showed high current density and long term stability of the photoelectron emission.