• Journal of the korean Society of Automotive Engineers
• /
• v.18 no.5
• /
• pp.96-120
• /
• 1996

현재 자동차용 복합재료를 생산하는데 유리한 제조방법으로는 압축성형 (Compression Molding), 액상성형(Liquid Molding), 인발성형(Pultrusion), 필라멘트 와인딩성형(Filament Winding)등이 있다. 압축성형은 현재 자동차 외장부품 성형에 널리 알려져 있는 SMC(Sheet Molding Compound)성형, 최근에 많은 연구가 되고 있는 LMPC(Low Pressure Molding Compound)성형, GMT(Glass Mat Reinforced Thermoplastics)성형 등이 있다. 액상성형은 RTM(Resin Transfer Molding)과 VARI (Vacuum Assisted Injection Molding), SRIM(Structure Reaction Injection Molding) 등이 있으며, 자동차 산업뿐만 아니라 일반 산업에서도 최근 많은 각광을 받고 있다. 그러므로 본 소고에서는 자동차용 복합재료의 제조에 널리 사용되는 성형공정에 대하여 간단히 살펴보고, 자동차 부품에 있어서의 복합재료 응용 현장과 최근 환경문제가 대두되면서 관심의 초점이 되고 있는 자동차용 복합재료 재활용 기술에 대하여 고찰하고자 한다.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.53 no.8
• /
• pp.415-419
• /
• 2004

A pulse power supply using IGBTs and MPC (magnetic pulse compression) circuit was developed for a metal vapor laser. The life time of the pulse power supply is expected to be much longer than that of a vacuum tube or thyratron type pulse power supply. A series-connected IGBT array generated a long pulse of its pulse width 2 ${\mu}\textrm{s}$ md then it was compressed to less than 100 ns by a three stage MPC circuit. This pulse power supply was applied to a laser plasma tube of 10 mm inner diameter and 0.5 m discharge length. and successfully operated.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.2
• /
• pp.279-285
• /
• 2013

The feasibility of substituting a composite mold for an aluminum mold in the fabrication of a small ship propeller was investigated. A small three-blade aluminum propeller was used as a plug for manufacturing the composite mold. A GRPG composite mold and propeller were made from an unsaturated polyester resin, Epovia gelcoat, and woven and mat glass fibers using the compression and vacuum method at room temperature. The hardness and surface roughness and the strength and deformation of the compression and suction molds were experimentally determined. The results were compared with the ISO 484/2 standard and some aluminum alloy materials. The results showed that the deformation of the mold satisfied the tolerance of the thickness of the blade. Some characteristics of the GRPG composite mold were better than those of the aluminum alloy mold (surface smoothness, weight, performance, and cost), and some characteristics were similar (detachment ability and life-cycle). Therefore, the composite mold is considered suitable for the fabrication of a small composite ship propeller.

• Journal of Korean Neurosurgical Society
• /
• v.45 no.4
• /
• pp.209-212
• /
• 2009

Objective : Avascular necrosis (AVN) of the vertebral body is known as a relatively uncommon phenomenon in a vertebral compression fracture (VCF). The outstanding radiologic findings of AVN are intravertebral vacuum phenomenon with or without fluid collection. Several reports revealed that PVP or balloon kyphoplasty might be the effective treatment modalities for AVN. We also experienced excellent results when using PVP for the treatment of AVN of the vertebral body, and intend to describe the treatment's efficacy in this report. Methods : Thirty-two patients diagnosed with AVN of the vertebral body were treated with PVP. We measured the pre- and post-operative anterior body height and kyphotic angulation. The visual analogue scale (VAS) was used to determine the relief of back pain. Results : The anterior body height (pre-operative : 1.49 cm, post-operative : 2.22 cm) and kyphotic angulation (pre-operative : 14.47 degrees, post-operative : 6.57 degrees) were significantly restored (p<0.001). VAS was improved from 8.9 to 3.7. Pseudoarthrosis was corrected in all cases, which was confirmed by dynamic radiographs. Fluid collection was found in sixteen cases and was aspirated with serous nature. No organism and tumor cell were noted. Conclusion : PVP proved to be an effective procedure for the treatment of AVN of the vertebral body, which corrected dynamic instability and significantly restored the anterior body height and kyphotic angulation.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.223-223
• /
• 2012

Surface engineering plays a significant role in fabricating highly functionalized materials applicable to industrial and biomedical fields. Surface wrinkles and folds formed by ion beam or plasma treatment are buckling-induced patterns and controlled formation of those patterns has recently gained considerable attention as a way of creating well-defined surface topographies for a wide range of applications. Surface wrinkles and folds can be observed when a stiff thin layer attached to a compliant substrate undergoes compression and plasma treatment is one of the techniques that can form stiff thin layers on compliant polymeric substrates, such as poly (dimethylsiloxane) (PDMS). Here, we report two effective methods using plasma modification techniques for controlling the formation of surface wrinkles and folds on flat or patterned PDMS substrates. First, we show a method of creating wrinkled diamond-like carbon (DLC) film on grooved PDMS substrates. Grooved PDMS substrates fabricated by a molding method using a grooved master prepared by photolithography and a dry etching process were treated with argon plasma and subsequently coated with DLC film, which resulted in the formation of wrinkled DLC film aligning perpendicular to the steps of the pre-patterned ridges. The wavelength and the amplitude of the wrinkled DLC film exhibited variation in the submicron- to micron-scale range according to the duration of argon plasma pre-treatment. Second, we present a method for controlled formation of folds on flat PDMS substrates treated with oxygen plasma under large compressive strains. Flat PDMS substrates were strained uniaxially and then treated with oxygen plasma, resulting in the formation of surface wrinkles at smaller strain levels, which evolved into surface folds at larger strain levels. Our results demonstrate that we can control the formation and evolution of surface folds simply by controlling the pre-strain applied to the substrates and/or the duration of oxygen plasma treatment.

• Journal of Powder Materials
• /
• v.5 no.2
• /
• pp.98-110
• /
• 1998

$Ti_{52}Al_{48}$ and $(Ti_{52}Al_{48})_{100-x}B_x(x=0.5, 2, 5)$ alloys have been Produced by mechanical milling in an attritor mill using prealloyed powders. Microstructure of binary $Ti_{52}Al_{48}$ powders consists of grains of hexagonal phase whose structure is very close to $Ti_2Al$. $(Ti_{52}Al_{48})_{95}B_5$ powders contains TiB2 in addition to matrix grains of hexagonal phase. The grain sizes in the as-milled powders of both alloys are nanocrystalline. The mechanically alloyed powders were consolidated by vacuum hot pressing (VHP) at 100$0^{\circ}C$ for 2 hours, resulting in a material which is fully dense. Microstructure of consolidated binary alloy consists of $\gamma$-TiAl phase with dispersions of $Ti_2AlN$ and $A1_2O_3$ phases located along the grain boundaries. Binary alloy shows a significant coarsening in grain and dispersoid sizes. On the other hand, microstructure of B containing alloy consists of $\gamma$-TiAl grains with fine dispersions of $TiB_2$ within the grains and shows the minimal coarsening during annealing. The vacuum hot pressed billets were subjected to various heat treatments, and the mechanical properties were measured by compression testing at room temperature. Mechanically alloyed materials show much better combinations of strength and fracture strain compared with the ingot-cast TiAl, indicating the effectiveness of mechanical alloying in improving the mechanical properties.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.335-335
• /
• 2010

한국표준과학연구원 진공센터에서는 국제규격에 바탕을 둔 저진공펌프 종합특성평가시스템을 구축하여 $1100mbar\;{\sim}\;10^{-3}mbar$ 압력 영역에서의 저진공펌프(roots, dry 등)류의 종합특성평가를 시행하고 있다. 저진공펌프 종합특성평가시스템은 국제적 절차에 따른 신뢰성을 바탕으로 구축하고 있으나, 한국표준과학연구원 진공센터 뿐만 아니라, 국내에서도 고진공 종합특성평가 시스템을 구축 하고 있지 않다. 이에 반도체/디스플레이 등 첨단 공정에서 진공 환경을 조성하는 핵심장비인 고진공펌프의 종합특성평가시스템을 개발하고자 터보펌프(TMP) 1000L/s 급의 database를 구축 하였다. 터보펌프(TMP)는 throughput method와 orifice method 두 가지 방법을 병행하여 pumping speed 측정한다. orifice method는 일종의 미세유량 측정 장치이며, 실험값과 계산값 유량의 오차 범위가 작고 신뢰성을 확보하면 throughput method 만으로 측정할 수 있다. Througput method는 $10^{-6}mbar$ 압력 이상의 영역을 측정하며, ultimate pressure 및 $150^{\circ}C$의 bake-out 을 진행하여 base pressure을 측정 할 수 있으며, $10^{-6}mbar$ 압력 이상의 pumping speed를 측정 할 수 있다. 이에 따른 정압형 유량시스템을 개발 중에 있으며, inlet pressure와 outlet pressure를 이용한 compression ratio를 측정 한다. Orifice method는 ultimate pressure와 base pressure을 측정하며, leak valve를 이용한 컨덕턴스(C)로 pressure ratio을 이용하여 유량값을 계산하며, $10^{-6}mbar$ 압력 이하의 pumping speed를 측정할 수 있다. 또한 throughput method와 orifice method의 pumping speed 뿐만 아니라 소비전력 및 소음, 진동, 온도 등 특성평가 관련 사항들의 전반적인 사항을 평가하여 터보펌프(TMP) 1000L/s 급의 database를 구축한다. 향후 예비 실험을 통한 고진공펌프의 종합특성평가시스템을 완비해 나가며, 고진공펌프 종합 특성평가시스템을 통하여 국제적으로 공인받을 수 있는 평가기준을 확립하고 그 기준에 의한 진공/기계적 성능의 전방위적인 종합특성진단과 공정대응성 평가 등 국제적 기술 신뢰성을 확보하고자 한다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.356-356
• /
• 2010

Tribological behaviors of the hard film on soft substrate system were explored using the hard thin film of diamond-like carbon (DLC) coated the soft polymer of polydimethysiloxane (PDMS). A DLC film with the Young's modulus of 100 GPa was coated on PDMS substrate with Young's modulus of 10 MPa using plasma enhanced chemical vapor deposition (PECVD) technique. The deposition time was varied from 10 sec to 10 min, resulting in nanoscale roughness of wrinkle patterns with the thickness of 20 nm to 510 nm, respectively, at a bias voltage of $400\;V_b$, working pressure 10 mTorr. Nanoscale wrinkle patterns with 20-100 nm in width and 10-30 nm height were formed on DLC coating due to the residual stress in compression and difference in Young's modulus. Nanoscale roughness effect on tribological behaviors was observed by performing a tribo-experiment using the ball-on-disk type tribometer with a steel ball of 6 mm in diameter at the sliding speed of 220 rpm, normal load of 1N and 25% humidity at ambient temperature of $25^{\circ}C$. Friction force were measured with respect to thickness change of coated DLC thin film on PDMS. It was found that with increases the thickness of DLC coating on PDMS, the coefficient of friction decreased by comparison to that of the uncoated PDMS. The wear tracks before and after tribo-test were analyzed using SEM and AFM.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.46-46
• /
• 2010

고진공펌프 중의 하나인 터보분자펌프(turbo-molecular pump: TMP)는 반도체/디스플레이 등 첨단 공정에서 진공 환경을 조성하는 핵심장비로서 현재 한국표준과학연구원 진공기술센터에서 개발 중인 고진공펌프 종합특성평가시스템을 구축 중이며, 1000 L/s 및 2500L/s 배기속도 용량을 가지는 터보분자펌프(TMP)의 database를 구축하고 있다. 이에 터보분자펌프(TMP)의 배기속도 측정 시 사용되는 가스의 분자류 영역에 따른 배기속도의 변화를 연구하고자 한다. 터보분자펌프(TMP)의 배기속도는 분자류 영역에 따라 상이한 배기속도를 가진다. 특히 가벼운 분자들은 터보분자펌프(TMP)로 배기시키기 어려우며, 분자량이 작은 가스들은 분자량이 큰가스 분자들에 비해 압축비(compression ratio)도 작아진다. 압축비가 큰 경우에는 실재 운전조건에 무관하게 배기속도가 최대값을 가지지만, 압축비가 작을 경우에는 운전 시 터보분자펌프(TMP)의 압축비에 따라 배기속도가 달라 질 수 있으며, 압축비는 펌프의 inlet에서의 압력과 exhaust에서의 압력의 비이다. 즉, 가벼운 기체 분자(H2, He 등)들은 무거운 기체 분자(N2, Ar 등)들에 비해 배기속력이 작아진다. 현재 개발 중인 한국표준과학연구원 진공기술센터의 고진공 종합특성평가시스템을 이용하여 분자류 영역에 따른 가벼운 기체 분자와 무거운 기체 분자의 배기속도를 측정하여 분자류 영역에 따라 상이한 배기속도의 변화를 연구하고자 한다. 본 논문에서는 터보분자펌프(TMP)의 분자류 영역에 따른 가벼운 기체 He과 무거운 기체 N2를 사용하여 압축비의 변화와 배기속도 측정에 관해 상관관계를 제시하며, 분자류 영역에 따른 터보분자펌프(TMP)의 배기속도 운전성능을 제시하고자 한다.

• Journal of Chest Surgery
• /
• v.51 no.6
• /
• pp.390-394
• /
• 2018

Background: The nonsurgical treatment of chest wall deformity by a vacuum bell or external brace is gradual, with correction taking place over months. Monitoring the progress of nonsurgical treatment of chest wall deformity has relied on the ancient methods of measuring the depth of the excavatum and the protrusion of the carinatum. Patients, who are often adolescent, may become discouraged and abandon treatment. Methods: Optical scanning was utilized before and after the intervention to assess the effectiveness of treatment. The device measured the change in chest shape at each visit. In this pilot study, patients were included if they were willing to undergo scanning before and after treatment. Both surgical and nonsurgical treatment results were assessed. Results: Scanning was successful in 7 patients. Optical scanning allowed a visually clear, precise assessment of treatment, whether by operation, vacuum bell (for pectus excavatum), or external compression brace (for pectus carinatum). Millimeter-scale differences were identified and presented graphically to patients and families. Conclusion: Optical scanning with the digital subtraction of images obtained months apart allows a comparison of chest shape before and after treatment. For nonsurgical, gradual methods, this allows the patient to more easily appreciate progress. We speculate that this will increase adherence to these methods in adolescent patients.