• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.42 no.1
• /
• pp.35-44
• /
• 2022

The V_S30 map is used as a key variable for site amplification in the ShakeMap, which predicts ground motion at any site. However, no V_S30 map considering Korean geology and geomorphology has been developed yet. To develop a proxy-based V_S30 map, we used 1,101 V_S profiles obtained from a geophysical survey and collected proxy layers of geological and topographical information for the Korean Peninsula. Then, V_S30 prediction models were developed using linear regression analysis for each geological age considering the distribution of V_S30. As a result, models depending on geomorphology were suggested per each geologic group, including Quaternary, Fill, Ocean, Mesozoic group and Precambrian. Resolution of map is doubled from that of V_S30 map by U.S. Geological Survey (USGS). Standard deviation of residual in natural log of proxy-based V_S30 map is 0.233, whereas standard deviation of slope-based USGS V_S30 map is 0.387. Therefore, the proxy-based V_S30 map developed in this study is expected to have less uncertainty and to contribute to predicting more accurately the ground motion amplitude.

• The Transactions of the Korea Information Processing Society
• /
• v.1 no.3
• /
• pp.391-397
• /
• 1994

In this paper, we have developed a PLD Designer which is a design tool for digital circuits design using PLD device. PLD designer consists of a state graphic editor to extract boolean equations from state table within 20 states of FSM and a pin map editor to assign pin map for PLD device(PAL16R4, PAL22V10, GAL16V8, etc), which is suitable for extracted boolean equations. Also pin map editor generates a necessary JEDEC file to implement PLD device by using fuse map and checksum algorithm. To verify extracted boolean equation, we have developed simulation test vector generation algorithm. The results of JEDEC files generated by PLD designer is same with the results of JEDEC files generated by PALASM.

• The Pure and Applied Mathematics
• /
• v.4 no.2
• /
• pp.115-119
• /
• 1997

We show that if $f_{i}$:$X_{i}$ longrightarrow Y is strongly continuous(resp. weakly continuous, set connected, compact, feebly continuous, almost-continuous, strongly $\theta$-continuous, $\theta$-continuous, g-continuous, V-map), then F : $X_1 \bigoplus X_2$longrightarrow Y is strongly continuous(resp.weakly continuous, set connected, compact, feebly continuous, almost-continuous, strongly $\theta$-continuous, $\theta$-continuous, g-continuous, V-map).

• Korean Journal of Radiology
• /
• v.22 no.8
• /
• pp.1352-1368
• /
• 2021

Objective: For an accurate dynamic contrast-enhanced (DCE) MRI analysis, exact baseline T1 mapping is critical. The purpose of this study was to compare the pharmacokinetic parameters of DCE MRI using synthetic MRI with those using fixed baseline T1 values. Materials and Methods: This retrospective study included 102 patients who underwent both DCE and synthetic brain MRI. Two methods were set for the baseline T1: one using the fixed value and the other using the T1 map from synthetic MRI. The volume transfer constant (K^trans), volume of the vascular plasma space (v_p), and the volume of the extravascular extracellular space (v_e) were compared between the two methods. The interclass correlation coefficients and the Bland-Altman method were used to assess the reliability. Results: In normal-appearing frontal white matter (WM), the mean values of K^trans, v_e, and v_p were significantly higher in the fixed value method than in the T1 map method. In the normal-appearing occipital WM, the mean values of v_e and v_p were significantly higher in the fixed value method. In the putamen and head of the caudate nucleus, the mean values of K^trans, v_e, and v_p were significantly lower in the fixed value method. In addition, the T1 map method showed comparable interobserver agreements with the fixed baseline T1 value method. Conclusion: The T1 map method using synthetic MRI may be useful for reflecting individual differences and reliable measurements in clinical applications of DCE MRI.

• Bulletin of the Korean Mathematical Society
• /
• v.56 no.5
• /
• pp.1327-1340
• /
• 2019

We establish a monotonicity formula of V-harmonic maps by using the stress-energy tensor. Use the monotonicity formula, we can derive a Liouville type theorem for V-harmonic maps. As applications, we also obtain monotonicity and constancy of Weyl harmonic maps from conformal manifolds to Riemannian manifolds and ${\pm}holomorphic$ maps between almost Hermitian manifolds. Finally, a constant boundary-value problem of V-harmonic maps is considered.

• IEIE Transactions on Smart Processing and Computing
• /
• v.2 no.2
• /
• pp.45-56
• /
• 2013

The precise identification of vehicle positions, known as the vehicle localization problem, is an important requirement for building intelligent vehicle ad-hoc networks (VANETs). To solve this problem, two categories of solutions are proposed: stand-alone and data fusion approaches. Compared to stand-alone approaches, which use single information including the global positioning system (GPS) and sensor-based navigation systems with differential corrections, data fusion approaches analyze the position information of several vehicles from GPS and sensor-based navigation systems, etc. Therefore, data fusion approaches show high accuracy. With the position information on a set of vehicles in the preprocessing stage, data fusion approaches is used to estimate the precise vehicular location in the local map building stage. This paper proposes an efficient local map building scheme, which increases the accuracy of the estimated vehicle positions via V2V communications. Even under the low ratio of vehicles with communication modules on the road, the proposed local map building scheme showed high accuracy when estimating the vehicle positions. From the experimental results based on the parameters of the practical vehicular environments, the accuracy of the proposed localization system approached the single lane-level.

• Proceedings of the KIEE Conference
• /
• 2001.11b
• /
• pp.377-379
• /
• 2001

Contamination flashover is responsible for insulator electrical failures. Particularly, in Korea, with its perennially dry spring, the first spring rain often cause serious line outages by forming a conductive liquid film on the insulator surface. Rainwater and fog are not normally conductive but unfortunately atmospheric dust deposited on the insulator surface contains soluble salts which may lead to bad condition of insulation by combining watery and salts. Transmission design engineers have used a contamination map drawn on the traditional paper map. But it is not convenient because it does not include the information of Geographic Information accurately. This paper explains the newly developed salt contamination map program using Geographic Information System, which provide accurate geographic information. The program is designed to use four parts of datum, salt contamination levels, 345kV & 154 kV transmission lines, power plants & substations and background map. The digital background map is composed of raster files, the others are done by vector map.

• Communications of the Korean Mathematical Society
• /
• v.36 no.1
• /
• pp.173-187
• /
• 2021

In this paper, we deal with the notion of a v-semi-slant submersion from an almost Hermitian manifold onto a Riemannian manifold. We investigate the integrability of distributions, the geometry of foliations, and a decomposition theorem. Given such a map with totally umbilical fibers, we have a condition for the fibers of the map to be minimal. We also obtain an inequality of a proper v-semi-slant submersion in terms of squared mean curvature, scalar curvature, and a v-semi-slant angle. Moreover, we give some examples of such maps and some open problems.

• Journal of Institute of Control, Robotics and Systems
• /
• v.21 no.12
• /
• pp.1142-1151
• /
• 2015

In this paper, High performance torque control based on the flux mapping of 48V Wound Rotor Synchronous Motor has been studied to improve torque control. Flux map considering MTPA (Maximum Torque Per Ampere), MFPT (Minimum Flux Per Torque), Maximum efficiency point at the same torque command and flux command for each field current was produced. Current map using flux mapping of Each field current was applied to the MTPA, MFPT. Generating a current vector locus was to determine the characteristics of the operation region. Through the Matlab/Simulink simulation, difference between speed-torque map and flux map was represented. The suggested flux map was tested actual experiments on a dynamometer.

• 제어로봇시스템학회:학술대회논문집
• /
• 1992.10a
• /
• pp.31-36
• /
• 1992

This paper describes the development of a 'General-purpose ETRI MAP interface module' (GEM) for a Mini-MAP network. GEM operates as a Mini-MAP node in our FA system. To communicate between GEM and programmable devices such as PLC, CNC, and robot, RS232C is used, which is a traditional method. A Mini-MAP host system controls and monitors programmable devices via GEM. The Mini-MAP function of GEM is implemented and tested on the basis of the MAP V3.0.