• Journal of Welding and Joining
• /
• 제27권4호
• /
• pp.67-72
• /
• 2009

In this paper, arc characteristics of V groove joints using pulsed GMA welding were found out. The bevel angles of $22.5^{\circ}$ and $30.0^{\circ}$ were chose to make the V groove configuration with the groove angles of $45^{\circ}$ and $60.0^{\circ}$, respectively. In the experiment, the arc current waveform measurement and the high speed photography were taken to investigate the arc characteristics for a single-beveled asymmetric workpiece. Consequently, the welding current was changed abnormally around the edge of groove. As the arc moved close to the groove face, the welding current was increased rapidly because the welding arc was affected by the inclined surface. Also the welding current waveforms were measured for the double-sided symmetric workpiece to verify the previous measurements for the single-beveled workpiece, and similar current waveforms were found.

• 한국강구조학회 논문집
• /
• 제26권5호
• /
• pp.407-418
• /
• 2014

본 연구에서는 HSA800 후판 강재에 적합한 용접재를 선정하고자 휨-인장실험을 수행하였다. 본 연구 수행 당시 HSA800 강재에 적용가능한 용접재로 GMAW 용접재(외국산)와 FCAW 용접재(국내산) 두 가지가 추천되어 이들을 사용하였다. 선행연구인 표준인장실험 결과를 바탕으로 맞댐용접상세와 루트간격을 주요 실험변수로하여 실물크기의 보 실험을 통해 용접부의 성능을 평가하였다. 강도 측면에서 모멘트 및 플랜지 축력 전달에 대한 조건은 두 용접재 모두 만족하였으나 연성능력 측면에서 GMAW 용접재보다는 FCAW 용접재가 일관되고 우수한 거동을 보임이 실험적으로 확인되었다. 특히 GMAW 용접재는 용접효율과 작업성의 문제로 현장에서의 상향용접이 어려운 것으로 파악되었다. 같은 완전용입용접이라도 Single bevel보다는 V-groove가 안정적인 구조거동을 보이는 것으로 나타났다. 표준인장실험결과와 휨-인장실험결과를 토대로 HSA800 후판재의 용접상세 및 용접재를 제시하였다.

• 한국자동차공학회논문집
• /
• 제22권2호
• /
• pp.141-147
• /
• 2014

This study aims to investigate the influence of bevel angles on the fatigue life of V-groove butt-welded joints with back-plates made by SM490A steel material, generally used for excavators, because changes in the geometry, material and surface properties of welded regions affect the fatigue life of welded structures. Butt type test specimens were prepared by the $CO_2$ welding of rolled steel plates (SM50A steel) with a thickness of 13.5 mm at a welding speed of 30 cm/min and these Butt type test specimens had two different groove angles, which are $40^{\circ}$ (A type) and $30^{\circ}$ (B type). In order to investigate differences in fatigue life between two types, 4-point bending fatigue tests were conducted with a stress ratio of R=0.1 under the cyclic loading environment at a frequency of 5 Hz at room temperature. The fatigue life of A type specimens was approximately 7% higher than that of B type specimens. The stress concentration factors calculated by finite element analysis were 2.16 for A type and 2.25 for B type, whose difference was caused by the influence of the back-plates of butt-welded structures. The current results could provide important guidelines to determine the V-groove angle of butt-welded joints with a satisfactory fatigue life, although under severe operating conditions.

• Journal of Welding and Joining
• /
• 제22권4호
• /
• pp.59-64
• /
• 2004

The purpose of this study is to investigate the influence of weld bead profiles on stress concentration factors of double V groove butt-welded joints. The influence of three parameters such as toe radii, flank angles and bead heights on the stress concentration factors is studied by finite element analysis. It is shown that the three parameters have similar effects on the stress concentration factors. Finally a formula to estimate the stress concentration factors considering the three parameters and others is proposed and estimated results are compared with the results obtained by finite element analysis.

• 소성∙가공
• /
• 제16권8호
• /
• pp.603-613
• /
• 2007

This paper is concerned with joining of thin metal sheets by single stroke clinching process. This method has been used in sheet metal work as it is a simple process and offers the possibility of joining similar-dissimilar thin sheet metals. Clinching generates a joint by overlapping metal sheets deforming plastically by punching and squeezing sequence. AA 5754 aluminum alloy of 0.5 mm thick sheets have been selected as a modal material and the process has been simulated under different process conditions and the results have been analyzed in terms of the quality of clinch joints which are influenced mainly by tool geometries. The rigid-plastic finite element method is applied to analyses in this paper. Analysis is focused mainly on investigation of deformation and material flow patterns influenced by major geometrical parameters such as die diameter, die depth, groove width, and groove corner radius, respectively. To evaluate the quality of clinch joints, four controlling or evaluation parameters have been chosen and they are bottom, neck thickness of bottom and top sheets, and undercut thickness, respectively. It has been concluded from the simulation results that the die geometries such as die depth and diameters are the most decisive process parameters influencing on the quality of clinch joints, and the bottom thickness is the most important evaluation parameter to determine if the quality of clinch joints satisfies the demand for industrial application.

• 한국강구조학회 논문집
• /
• 제25권4호
• /
• pp.431-440
• /
• 2013

본 연구에서는 HSA800 후판 강재에 적합한 용접재를 선정하고자 표준인장실험을 수행하였다. 본 연구 수행 당시 HSA800 강재에 적용가능한 용접재로 GMAW 용접재(외국산)와 FCAW 용접재(국내산) 두 가지가 추천되어 이들을 사용하였다. 맞댐용접상세와 루트간격을 주요 실험변수로하여 표준인장실험을 통해 용접부의 성능을 평가하였다. 강도에 대한 설계요구조건은 두 용접재 모두 만족하였으나 연성능력 측면에서 GMAW 용접재 보다는 FCAW 용접재가 일관되고 우수한 거동을 보임이 실험적으로 확인되었다. 특히 GMAW 용접재는 용접효율과 작업성의 문제로 현장에서의 상향용접이 어려운 것으로 파악되었다. 같은 완전용입용접이라도 Single bevel보다는 V-groove가 안정적인 구조거동을 보이는 것으로 나타났다. 또한 현행 용접기준의 표준루트 간격을 벗어날 경우 용착의 어려움으로 비정상 파단면이 형성되고 접합성능도 저하됨이 확인되었다. 부분용입용접 접합부의 실험결과에 의할 때 현행 AISC 기준의 부분용입용접부 강도규정은 매우 보수적임이 확인되었다.

• Journal of Welding and Joining
• /
• 제21권3호
• /
• pp.85-91
• /
• 2003

Narrow gap welding has many advantages over conventional V-grooved butt welding such as high productivity, small deformation and improved mechanical property of joints. With narrower groove gap, less arc heat input is expected will all the other advantages of narrow gap welding. The main defects of narrow gap welding include the lack of root fusion, convex bead surface and irregular surface, all of which have negative effects on the next welding pass. This paper suggests an up-and-down torch oscillation for ultra narrow gap welding with gap size of 5mm and investigates the proper welding conditions to fulfill the reliable and high welding quality. First, GMA welding model was suggested for ultra narrow gap welding system with Halmoy's model referenced for wire melting modeling. And the arc length in ultra narrow gap was defined. Secondly, based on the experimental results of up-and-down torch oscillation welding, phase shift of current and wire extension length were simulated for varying oscillation frequency to show that weld the bead shape in ultra narrow gap welding can be predicted. As the result, it was confirmed that reliable weld quality in ultra narrow gap welding can be achieved with up-and-down torch oscillation above 15Hz due to its ability to provide uniform heat input along the sidewall of gap.