• 대한기계학회논문집
• /
• 제15권2호
• /
• pp.557-566
• /
• 1991

The metal V-belt behavior of a continuously variable transmission was investigated analytically and experimentally. Numerical results showed that nondimensional belt radial displacement increased in the radial inward direction for the driven pulley, while that of the driver pulley increased for the first 90 degrees of the active are and decreased with the increasing torque load. Experimental results for the belt radial displacement were in good agreement with the theoretical results. However, the absolute magnitude of the belt radial displacement was so small that the change in the belt displacement could not be measured in the experimental range except for the inlet region of the driven pulley, where the radial inward displacement was observed due to the effect of bending moment. The speed ratio-axial force relationship derived from the belt behavior analysis also showed god agreement with the experiment.

• 대한기계학회논문집
• /
• 제13권5호
• /
• pp.847-854
• /
• 1989

본 연구에서는 V-벨트 CVT의 핵심인 변속비-부하토오크-축력에 대한 이론적 연구에 이어 실험적 연구를 통하여 전 연구에서 구한 이론식과 비교 검토하고 V-벨트 CVT의 기초 설계자료를 얻고자한다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2004년도 추계학술대회 논문집
• /
• pp.822-825
• /
• 2004

Continuously variable transmission (CVT) mechanisms considered here is a V-belt drive with two variable-diameter pulleys and effective diameters. One pulley was set by a mechanical link while the other was spring-loaded to provide automatic correspondence. The center distance between the two variable-diameter pulleys was fixed. Experimental studies were executed to analyze efficiencies as change of its speed ratio.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 추계학술대회논문집A
• /
• pp.740-745
• /
• 2001

There are two kinds of method to calculate the equivalent friction coefficients at V groove. One is to consider the firction in radial direction. The other is to neglect the friection in radial direction. The values calculated from the two methods is different of which ratio is in the range from two times to five times. So it is necessary to study which is correct in the view of force equilibrium and machine design.

• 융합신호처리학회논문지
• /
• 제23권1호
• /
• pp.1-7
• /
• 2022

타이밍벨트는 동력전달 요소로서 V벨트와 기어의 장점을 살린 톱니붙이 전동 벨트로서 미끄러지지 않고 소음도 적어 기구에서 회전축이나 직선 운동에서 동력을 전달할 때 동력 전달 장치로 사용되고 있다. 기어처럼 등간격의 홈을 가진 벨트 풀리와 홈에 정확히 맞물리도록 동일한 간격의 홈을 가진 타이밍 벨트를 통해 회전을 정확하게 전달할 수가 있다. 특히 출력축에 타이밍벨트가 사용된 메커니즘에서 타이밍벨트의 강성을 포함한 동적 특성이 시스템 전달 특성을 결정하게 되므로 그 중요성이 커진다. 본 논문에서는 제한된 범위의 움직임을 갖는 타이밍 벨트에 적용하여 강성을 증가시킬 수 있는 강성 강화 벨트를 제안하였다. 강성 강화 벨트의 동특성을 연구하기 위하여 강성 강화 벨트에 대한 운동방정식을 수립하고, 강성 강화 벨트에 대한 시뮬레이션 모델을 만들어 분석을 수행하였다. 운동 방정식과 시뮬레이션 모델의 분석 결과를 확인하기 위하여 강성 강화 벨트를 사용한 1축 회전 실험 장치를 제작하고 실험을 수행하였다. 운동 방정식, 시뮬레이션 모델, 실험을 통하여 제안한 강성 강화 벨트를 적용하면 타이밍벨트의 강성과 동특성을 개선할 수 있음을 확인하였다.

• Elastomers and Composites
• /
• 제44권3호
• /
• pp.299-307
• /
• 2009

본 연구는 자동차 엔진의 구동을 각종 부대 장치로 전달하는데 사용되는 V-rib 벨트 재료의 내열성 및 내마모성을 향상시키기 위한 연구이다. 이를 위하여 고무 매트릭스는 EPDM과 CR, 그리고 충전제로 ZnO, 면 및 아라미드 섬유의 함량을 달리한 시편과 v-벨트를 만들어 내열성과 내마모성 그리고 기계적 성질을 조사하였다. CR 배합계에서 ZnO의 함량이 증가함에 따라 내마모성이 증가하였다. 또한 면섬유의 함량이 증가함에 따라 벨트상태에서 견딜 수 있는 구동시간은 증가하지만 내마모성은 감소하는 결과를 보였다. EPDM 배합계에서 면섬유의 충전한계는 30 phr정도였다. 또한 아라미드와 면섬유를 혼합 사용한 결과 구동시간과 내마모성을 동시에 증가시킬 수 있었으며, 그 단섬유의 최적 조성은 아라미드섬유/면섬유 비율이 1/5인 것으로 조사되었다. 동일한 면섬유 함량에서 EPDM 배합계 가 CR 배합계보다 우수한 물성을 보였다.

• Journal of Biosystems Engineering
• /
• 제24권2호
• /
• pp.99-106
• /
• 1999

This study was conducted to provide a direction for improving the performance of triangular-type belt clutch. The power transmission characteristics and the wear of belt were investigated for two types of pulley set theoretically and experimentally. The results of research were summarized as follows: 1) Based on the theoretical analysis for the life time of belt, the wear of belt could be reduced by increasing the sizes of driving V-pulley and tension pulley, and by decreasing the tension on V-belt. 2) The pulley set # 2 could transmit more power than the pulley set # 1 could at the same slop rate. While the slip rate was 2.36% on the pulley set # 2 at the maximum power transmission, the slip rate on the pulley set # 1 was increased up to 12.2% at the same condition. 3) From the 16 hours' fatigue test, the wear of belt used n the pulley set # 1 was observed severer than that in the pulley set#2. Also, it was found that the tensile strength of belt used in the pulley set # 2 was greater than that of belt used in the pulley set # 1.

• 대한기계학회논문집
• /
• 제14권2호
• /
• pp.349-357
• /
• 1990

Power transmission characteristics and speed ratio-torque load-axial force relationship for a metal V-belt CVT were investigated theoretically and experimentally. In the metal V-belt CVT drive, it was found that the power was transmitted by thrust force and that band tension should be greater than compression force between the metal blocks. The experimental results for the speed ratio-torque load-axial force relationship showed good agreement with those predicted using equations developed from theoretical considerations.

• 한국자동차공학회논문집
• /
• 제10권6호
• /
• pp.209-218
• /
• 2002

A V belt pulley is widely used in automotive industry. More than tow pulleys in one automobile are used, such items as crankshaft, water pump, air-con compressor and power steering pump. Although the shape and usage of pulleys are very simple, the design evaluation of a pulley design is difficult because the load conditions and the installation environment are complicated. So, we formulated the design evaluation for the V belt pulley by using CAE system, which enables to develop a design automation system. By using this system, an engineer can evaluate a pulley design easily without any painstaking effort, such as consideration of the complicated loads and CAE activities. Also the system helps to accumulate the design experience of a company, which guides the optimum design based on experience.

• 오토저널
• /
• 제12권6호
• /
• pp.30-39
• /
• 1990

The behavior of a V-belt CVT was investigated both analytically and experimentally. It was found that as the torque load increased, the belt radial displacement increased in inward radial direction for the driven pulley while the radial displacement decreased slightly and increased for the driver pulley. The relative belt displacement for the driver was negligible compared with that of the driven. The experimental results were in good accordance with the theoretical results except for the inlet and exit region of the pulley. The speed ratio-torque load-axial force relationship derived from the belt behavior analysis also showed good agreement with the experiment. It is suggested that the results of this paper can be used as basic design informations of a V-belt CVT.