• Proceedings of the KSME Conference
• /
• 2000.04a
• /
• pp.803-808
• /
• 2000

This thesis studied whether friction welding of SPSS, localized torsion bar material could be accomplished or not. And then optimum welding conditions were examined and leaded through tensile, impact, torsion and hardness test after postweld heat treatment of the actual field condition. Obtained results were as follows; Linear relationship was existed between heating time and total upset, and a quadratic equation model could be made between tensile strength and heating time. Optimum welding conditions with fine structure were as follows in case total upset(U)=8.5mm; the number of rotations(n)=2,000 rpm, heating pressure($p_1$)=80MPa, upset pressure($p_2$)=200MPa, heating time($t_1$)=4sec, upset time($t_2$)=3 sec.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.45 no.9
• /
• pp.724-733
• /
• 2017

Accidents caused by upset condition leads to fatal damage to both manned and unmanned aircraft. This paper deals with real-time detection of these aircraft upset situations to prevent further severe situations. Firstly, the difference between sensor measurement and predicted measurement from Extended Kalman filter is monitored to determine whether a target aircraft goes into an upset condition or not. In addition, repeating the time update stage of the Extended Kalman filter for a specific length of time can enable future upset situation prediction. The results of aforementioned both the approaches will build a bridge to upset prevention for future generation of manned/unmanned aircraft.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1998.03a
• /
• pp.71-75
• /
• 1998

This study deals with the friction weldability of A7075-T6 having high specific strength. The friction welding conditions used are rotation speed 2000rpm, friction pressure 40MPa, friction time 1.5sec, upset pressure 40~100MPa, upset time 5sec. First, upset length was measured by displacement transducer. The plastic flow in 7075-T6 weld generates convex lens shaped resion by friction and concave lens shaped resion by axial force. Under the condition of upset pressure 85MPa, the friction welds have tensile strength of 552MPa and shear strength of 262MPa.

• Proceedings of the KWS Conference
• /
• 2000.10a
• /
• pp.192-195
• /
• 2000

This paper describes a fundamental investigation of the friction welding condition for pure copper/pure titanium and the effect of friction time, upset pressure on the mechanical and metallurgical properties of friction welding. Under the constant upset pressure, the tensile strength make a little difference with an increase in friction time. At the constant friction time, the tensile strength increased with an increase in upset pressure. The tensile fracture of Cu to Ti joint occurred in Cu base material near interface.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.50 no.2
• /
• pp.93-101
• /
• 2022

It is essential to prevent LoC(Loss-of-Control) or upset situations caused by stall, icing or sensor malfunction in aircraft, because it may lead to the crash of the aircraft. With this regard, it is crucial to correctly identify the dynamic characteristics of aircraft in such upset conditions. In this paper, we present a SID(System IDentification) method utilizing the moving-window based least-square and the adaptive-order ZKF(Zonotopic Kalman Filter), which is more effective than the existing Kalman-filter based SID for the aircraft in upset condition at a high angle of attack with temporary sensor malfunction. The proposed method is then tested on real flight data and compared with the existing one.

• Journal of Welding and Joining
• /
• v.8 no.4
• /
• pp.20-26
• /
• 1990

In this study, to make research on its optimum condition in friction weld when the heating pressure is change during 1.6 to 3.0 $kgf/mm^2$, the experiment was performed with metal bearing under various condition; 1600 r.p.m spindile speed, 0.6 $kgf/mm^2$ preheating pressure, upset pressure 2.6 $kgf/mm^2$, 0.5 seconds preheating time, 1.7 seconds heating time, water and air was ejected 6 $kgf/mm^2$ into the bushing. On the basis of the experimental results, the following conclusion are drawn; 1) At the area of weld interface, the heardness is shown the maximum value and heat-affected zone about 0.5mm both sides. 2) Bending strength is shown the optimum heating pressure 2.4 kgf/mm. 3) With the approach of the flash, Sn is increased only 2 mm in A-alloy structure.

• Proceedings of the KIEE Conference
• /
• 1999.07d
• /
• pp.1934-1937
• /
• 1999

A copper-tungsten sintered alloy(Cu-W) has been friction-welded to a tough pitch copper (Cu) in order to investigate friction weldability. The tensile strength of the friction welded joint was increased up to 87% of the Cu base metal under the condition of friction time 1.0 see, friction pressure 40MPa and upset pressure 100MPa, upset time 5.0 sec. And it is related to upset pressure rather than friction time. Mixed layer was formed in the Cu adjacent weld interface and W particles which were included in mixed layer could induce fracture in the Cu adjacent to the weld interface. Thickness of mixed layer was reduced as upset pressure increase.

• Journal of Advanced Marine Engineering and Technology
• /
• v.18 no.4
• /
• pp.69-76
• /
• 1994

Thermal elasto-plastic analysis of axi-symmetric body by the finite element method is presented in this paper for analyzing the process of upset forming of circular section extruded bar. The example of calculation for upset forming of Nimonic extruded bar is also presented. It is shown that remeshing of quadrilateral finite element is necessary because the very highly distorted element by plastic deformation disturbs the calculation. Calculated values for nodal points in new mesh are obtained from nodal points of old mesh by linear interpolation method. The experimental results are compared with calculated values. The appearance of upsetupset forming obtained by experimental method is very similar to that obtained by calculations. So, it is proved that the thermal elasto-plastic analysis of axi-symmetric body by the finite element method is very useful for finding the optimum upsetting condition.

• Journal of Ocean Engineering and Technology
• /
• v.16 no.6
• /
• pp.49-54
• /
• 2002

The Finite Element Method is applied to the determination of the deformed bulge profile and strain distribution during upset forming of cylindrical billets. From the results of simulation, the bulging along the z-axis becomes more severe with increasing eight reduction, and with increasing friction at the die-material interface. The present method can be used for the simple prediction of the deformed shape and strain distribution in upset forging of cylindrical billets with dissimilar fictional conditions at the die-material interfaces.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.15 no.1
• /
• pp.102-107
• /
• 2006

This study investigates the properties as the difference friction welding area on SM25C steel rod. The tensile and bending strength and of welded joints, the hardness distribution of welds, the microstructure of welds and the tensile fracture surfaces were mainly investigated through this experiment. The fixed friction welding conditions were revolution 2000rpm, friction pressure 70Mpa, friction time 1.5sec, upset pressure 100Mpa, upset time 2.0sec, upset length 2.8mm and changeable friction welding parameter was friction welding area.