콘크리트 믹서트럭의 덮개는 레미콘 플랜트에서 공사 현장까지의 운반 도중 굳지 않은 콘크리트의 유동성이 저하하지 않도록 사용하는데, 설문 결과 일반시민들에게 더러운 이미지를 주고 있다. 이러한 이미지로 인해 건설 산업 전체의 이미지에도 영향을 미칠 것으로 예상하여 덮개의 효용성 여부를 밝히기 위해 레미콘을 현장에 대기시켜 둔 채 유동성을 비롯한 공기량, 콘크리트 온도변화 등의 현장 실험을 실시하였다. 또한 이와 비교를 위해 동일한 조건으로 실내 실험을 병행하여 결과를 도출하였다. 실험 결과, 믹서트럭의 덮개는 슬럼프 저하에 미치는 영향이 적은 것으로 나타났다. 공기량 변화는 덮개 유무에 관계없이 60분까지는 적정한 수준으로 품질에 큰 영향을 미치지 않는 것으로 나타났다. 또한 콘크리트 압축강도는 덮개 유무에 관계없이 90분까지의 시료의 경우에 목표설계기준강도에 모두 적합한 것으로 나타났다.
Since a liquid-phase LPG injection system allows accurate control of fuel injection and increase in volumetric efficiency, it has advantages in achieving higher engine power and lower emissions compared to the mixer type LPG supplying system. However, this system also leads to an unexpected event called icing phenomenon which occurs when moisture in the air near the injector freezes and becomes frost around the nozzle hole due to extraction of heat from surrounding caused by instant fuel vaporization. As a result, it becomes difficult to control air/fuel ratio in engine operation, inducing exacerbation of engine performance and HC emission. One effort to mitigate icing phenomenon is to attach anti-icing injection tip in the end of nozzle. Therefore, in this study, the effect of engine operation parameters as well as surrounding conditions on icing phenomenon was investigated in a bench test rig with commercially-used anti-icing injection tips. The test results show that considerable ice was deposited on the surface near the nozzle hole of the anti-icing tip in low rpm and low load operating conditions in ambient air condition. This is because acceleration of detachment of deposited ice from the tip surface was induced in high load, high rpm conditions, resulting in decrease in frost accumulation. The results of the bench testing also demonstrate that little or no ice was formed at surrounding temperature below a freezing point since the absolute amount of moisture contained in the intake air is too small in such a low temperature.
본 연구에서는 GEC-Marconi 사의 H40 GaAs pHEMT 소자에 대해서 새롭게 수정한 Curtice 모델을 사용하여 대신호 통합모델을 구축하였다. 통합모델에는 DC 특성과 biss에 따른 소신호 및 잡음 특성이 모두 포함되어 있으며, 특히 수정되 Curtice 모델을 사용함으로써 gate-source 간의 전압이 증가함에 따라 나타나는 pHEMT 의 transconductance(이하 $g_{m}$) 특성을 매우 간단하면서도 물리적으로 설명할 수 있게 하였다. 또한 통합모델 내부에는 RF-choke를 사용함으로써 $g_{m}$, $R_{ds}$ 성분의 DC 상태와 AC 상태에서의 차이를 설명하게 하였다. 통합모델을 HP사의 simulation tool 인 MDS(Microwave Design System)의 SDD(Symbolically Defined Device)를 이용하여 구현한 후, 실제의 data와 비교한 결과 DC, small signal, 그리고 noise 에 대한 특성에 H40 pHEMT 와 대부분 일치함을 보았으며, 선형과 다양한 harmonic balance simulation 의 수렴성 및 정확성을 확인함으로써 본 모델을 이용한 경우 저잡음 증폭기, 발진기, 그리고 혼합기 등의 여러 부품설계를 할 수 있음을 보였다.
Journal of electromagnetic engineering and science
/
제14권2호
/
pp.61-67
/
2014
This paper presents a zero-IF CMOS RF receiver, which supports three channel bandwidths of 5/10/40MHz for LTE-Advanced systems. The receiver operates at IMT-band of 2,500 to 2,690MHz. The simulated noise figure of the overall receiver is 1.6 dB at 7MHz (7.5 dB at 7.5 kHz). The receiver is composed of two parts: an RF front-end and a baseband circuit. In the RF front-end, a RF input signal is amplified by a low noise amplifier and $G_m$ with configurable gain steps (41/35/29/23 dB) with optimized noise and linearity performances for a wide dynamic range. The proposed baseband circuit provides a -1 dB cutoff frequency of up to 40MHz using a proposed wideband OP-amp, which has a phase margin of $77^{\circ}$ and an unit-gain bandwidth of 2.04 GHz. The proposed zero-IF CMOS RF receiver has been implemented in $0.13-{\mu}m$ CMOS technology and consumes 116 (for high gain mode)/106 (for low gain mode) mA from a 1.2 V supply voltage. The measurement of a fabricated chip for a 10-MHz 3G LTE input signal with 16-QAM shows more than 8.3 dB of minimum signal-to-noise ratio, while receiving the input channel power from -88 to -12 dBm.
Purpose: The purpose of this study is to measure and compare a degree of setting expansion of dental stone by time depending on the mixing methods and mixing ratios of dental stone, to compare the surface state of each specimen with the use of an optical camera with microscope, and thereby to provide a fundamental material for making dental prostheses. Methods: The test on setting expansion of dental stone is based on ISO 6873. With two different mixing ratios and three kinds of stone mixing methods, test groups were created, and a total of six types of specimens (N=30) were made. Based on the specimens, the setting expansion rate of each one was measured in each time slot of 24 hours, and the surface of the set stone was measured. Results: According to the analysis on setting expansion rate of stone, the setting expansion of the specimen that was created in the way of vacuum mixing at normal mixing ratio was 0.1944% at 120 minutes; the setting expansion of the specimen that was created in the way of vacuum mixing at the mixing ratio which was 40% higher than normal mixing ratio was 0.195% at 120 minutes; the setting expansion of the specimen that was created in the way of mixing with hands at normal mixing ratio and then removing bubbles in vacuum mixer was 0.196% at 120 minutes. Conclusion: The setting expansion rate of each dental stone specimen was significantly different with the lapse of time up to 24 hours(p<.001).
본 논문에서는 LTE-Advanced 시스템에 적용할 수 있는 $0.13-{\mu}m$ CMOS RF Front-end 송신기를 제안한다. 제안하는 RF Front-end 송신기는 3GPP의 E-UTRA Band 7 주파수인 2500 ~ 2570 MHz 대역을 지원하며 +10 dBm의 출력 P1dB 특성을 가지고, 실제 동작에서는 +0 dBm 출력 전력을 제공한다. 회로의 성능은 레이아웃 후 Post Layout Simulation을 통해 검증하였으며, +0 dBm 출력 시 1.2 V의 공급 전압원으로부터 상향주파수변환기는 14 mA, 그리고 구동증폭기는 28 mA를 소모한다.
본 논문에서는 IMT-Advanced 시스템에 적용할 수 있는 0.13-${\mu}m$ CMOS 이중대역 송신단 RF Front-End를 제안한 다. 제안하는 이중대역 송신단 RF Front-End는 3 세대(802.11), 3.5 세대(Mobile WiMAX), 그리고 4 세대(IMT-Advanced) 시스템 주파수 대역을 모두 지원하기 위해서 2300~2700 MHz와 3300~3800 MHz의 이중 주파수 대역을 지원한다. 본 논문에서 제안하는 이중대역 송신단 RF Front-End는 1.2 V의 공급 전원에서 45mA의 전류를 소모한다. 회로의 성능은 레이아웃 후 검증(Post Layout Simulation)을 통해 검증하였으며, 2 GHz 대역에서 +0 dBm의 출력 파워, 3 GHz 대역에서 +1.3 dBm의 출력 파워를 나타낸다.
메이크업 제품에 있어서 특히 아이섀도나 블러셔와 같은 포인트 메이크업 제품의 제조시 화사함이나 광택을 부여하기 위하여 사용되는 펄 안료에 대하여 분쇄시간에 따른 입도분포 변화와 결합제로 사용되는 바인더의 영향에 따른 입도분포의 변화에 대하여 검토하였다. 고속 회전형 믹서기를 사용하였으며 레이져 회절${\cdot}$산란법을 이용하여 입도분포를 측정하였다. 평균경 5 um의 펄 안료인 경우 120 s간 분쇄하였을시 4.5 um로 입자경의 변화 폭이 작지만, $45{\;}{\mu}m$인 경우 27 um로 현저히 작아지며 그에 따라 본래의 광택감도 떨어지는 것을 확인할 수 있었다. 바인더의 경우, raw material의 입자사이즈에 따라 분쇄시간과의 상관성을 확인하였으며, 바인더 함량에 따라 입자간의 응집에 의하여 발생하는 분립체의 입도분포의 변화에 대해서도 고찰하였다.
Introduction: Surgical treatment of subclavian artery (SA) injury is challenging because approaching the lesion directly and clamping the proximal artery is difficult. This can be overcome by using an endovascular technique. Case 1: A 37-year-old male was drawn into the concrete mixer truck. He had a right SA injury with multiple traumatic injuries: an open fracture of the right leg with posterior tibial artery (PTA) injury, a right hemothorax, and fractures of the clavicle, scapula, ribs, cervical spine and nasal bone. The injury severity score (ISS) was 27. Computed tomography (CT) showed a 30-mm-length thrombotic occlusion in the right SA, which was 15 mm distal to the vertebral artery (VA). A self-expandable stent($8mm{\times}40mm$ in size) was deployed through the right femoral artery while preserving VA flow, and the radial pulse was palpable after deployment. Other operations were performed sequentially. He had a viable right arm during a 13-month follow-up period. Case 2: A 25-year-old male was admitted to our hospital due to a motorcycle accident. The ISS was 34 because of a hemothorax and open fractures of the mandible and the left hand. Intraoperative angiography was done through a right femoral artery puncture. Contrast extravasation of the SA was detected just outside the left rib cage. After balloon catheter had been inflated just proximal to the bleeding site, direct surgical exploration was performed through infraclavicular skin incision. The transected SA was identified, and an interposition graft was performed using a saphenous vein graft. Other operations were performed sequentially. He had a viable left arm during a 15-month follow-up period. Conclusion: The challenge of repairing an SA injury can be overcome by using an endovascular approach.
폴리프로필렌(PP)과 에틸렌-프로필렌-디엔 고무(EPDM)의 양쪽 성분에 특정 상호 작용기도입에 의한 상용성 향상효과를 연구하였다. PP는 무수말레인산으로 그래프트시켰고(PP-g-MAH), 다른 한 성분으로는 황산화 EPDM 이오노머(ZnSEPDM)를 사용하였다. 브라벤더 혼합기를 이용하여 $200^{\circ}C$에서 블렌딩을 행하였다. 상용성은 FTIR분광기로 분석하였고 또한, 동적기계적 물성으로 분석하였다. FTIR결과 PP-g-MAH 의 카보닐기는 단파장 쪽으로 이동하고, ZnSEPDM의 슬폰기는 장파장쪽으로 이동하는 것을 알 수 있었다. ZnSEPDM의 유리전이온도는 그 조성이 70wt.%까지는 증가하다가 70wt.%이상에서 감소하였다. FTIR 스펙트라와 유리전이온도 결과로부터 특정상호작용, 즉 쌍극자-이온 상호작용에 의해 PP-EPDM 사이의 상용성이 증가하는 것을 알 수 있었다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.