• Journal of the Society of Naval Architects of Korea
• /
• v.56 no.1
• /
• pp.23-33
• /
• 2019

Unmanned Surface Vehicle (USV) is being developed to do maritime survey and maritime surveillance at Korea Research Institute of Ships & Ocean engineering (KRISO). The goal is that USV should be operated at the maximum speed of 45 knots and it should be operated at sea state 4. Therefore the planing hull of USV should be excellent in resistance performance and manoeuvring performance. It is needed to check its performance using Experimental Fluid Dynamics (EFD), Computational Fluid Dynamics (CFD) or analytic method before designing the hull. In this study, resistance performance was analyzed by EFD and CFD. EFD with heave and pitch was performed at high speed towing system in Seoul National University. CFD was performed using SNUFOAM based on openFOAM with dynamic mesh to calculate running attitudes. The results of CFD were compared with EFD results. The results of CFD were resistance, running attitudes and wave height. The flow distribution and pressure distribution were also analyzed. The results of numerical resistance was under estimated than EFD. Even though the results of CFD have a slight limitation, it can be successfully used to estimate the resistance performance of planing hull. In addition it can be used as a supplement for EFD results.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.12 no.1
• /
• pp.892-901
• /
• 2020

We used a numerical method to estimate the hydrodynamic maneuvering derivatives for the heave-pitch coupling motion of an underwater glider. It is very important to assess the hydrodynamic maneuvering characteristics of a specific hull form of an underwater glider in the initial design stages. Although model tests are the best way to obtain the derivatives, numerical methods such as the Reynolds-averaged Navier-Stokes (RANS) method are used to save time and cost. The RANS method is widely used to estimate the maneuvering performance of surface-piercing marine vehicles, such as tankers and container ships. However, it is rarely applied to evaluate the maneuvering performance of underwater vehicles such as gliders. This paper presents numerical studies for typical experiments such as static drift and Planar Motion Mechanism (PMM) to estimate the hydrodynamic maneuvering derivatives for a Ray-type Underwater Glider (RUG). A validation study was first performed on a manta-type Unmanned Undersea Vehicle (UUV), and the Computational Fluid Dynamics (CFD) results were compared with a model test that was conducted at the Circular Water Channel (CWC) in Korea Maritime and Ocean University. Two different RANS solvers were used (Star-CCM+ and OpenFOAM), and the results were compared. The RUG's derivatives with both static drift and dynamic PMM (pure heave and pure pitch) are presented.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.50 no.7
• /
• pp.515-521
• /
• 2022

In this paper, we propose Quad BTC that compresses DSM files to allow random access for TRF (Terrain Referenced Flight). The terrain data used for TRF has a large data capacity to be stored in the UAV (Unmanned Aerial Vehicle), so its size must be reduced through compression. Conventional BTC (Block Truncation Coding) based compression methods are suitable for TRF because it can decode randomly accessing specific coordinates. However, These conventional methods have a problem that the error increases because the deviation of the data increases as the size of the block increases. In this paper, we propose Quad BTC method that adaptively divides a block in to 4 sub blocks and compresses to solve this problem. The proposed method may reduce errors because the size of the sub block can be adjusted within the block. Through simulation using actual terrain data, it is verified that Quad BTC has less error at the same compression ratio than conventional BTC and AM BTC.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2023.05a
• /
• pp.86-86
• /
• 2023

최근에 들어 환경보전과 지속가능한 하천관리의 중요성이 대두되고 있으며, 통합물관리에 있어 수리량과 수질을 연계한 통합 모니터링의 필요성이 커지고 있다. 수리량과 수질 분야에 대한 모니터링 기술은 지속적인 연구가 이루어져 왔으나, 각 분야의 개별적 연구로 인해 수리량과 수질을 통합하여 모니터링 하는 기술 개발은 미흡한 수준이다. 또한 수질 측정은 수질오염공정시험기준에 있는 채수 기준에 따라 채수하여 측정하고 있으며, 채수 지점은 하천의 수심별로 달리하여 정해진다. 수리 측정은 현장계측을 통한 2차원적 계측으로 진행하고 있어 수질 측정 시 채수지점과 수리 측정지점은 일치하지 않는다. 동일 지점에서의 수질과 수리량을 동시에 고려하고 있지 못한 모니터링은 본류와 지류의 혼합거동이 많은 국내 하천 특성을 반영하지 못한다. 또한 현재의 수질·수리 모니터링은 ADCP나 다항목수질측정기 같은 고가의 장비를 운영하며, 홍수기와 같은 고위험 계측 조건에서 인력을 통해 측정하고 있기에 고비용의 장비운영비와 인명 피해를 야기시키고 있다. 따라서 무인 원격 기술을 적용한 하천 모니터링 기술과 수질과 수리량의 데이터 연계를 통한 3차원 모니터링 기술의 확보는 하천관리에 있어 매우 필수적이다. 본 연구에서는 수중 무인 원격이동체인 ROV와 무인 원격이동체(USV)를 활용한 3차원 수질·수리 모니터링 기술 개발에 관한 연구를 수행하였다. 국내 하천 특성을 고려한 혼합거동을 분석하기 위해 ROV에 수중 GPS 장비와 수질센서를 부착시켜 수중 내 2차원으로 측정되는 수리량과 동일한 좌표를 가지는 수질자료를 계측하여 하천의 연직 분포와 수평적 분포를 통해 화학적 수리적 거동을 분석하여 하천의 3차원 혼합거동 양상을 판단할 수 있었다. 이와 같은 무인 원격이동체를 통한 3차원 수질·수리 모니터링 기술은 하천의 3차원 분석에서 수질·수리량 보간 자료로 활용 가능하며, 효율적인 모니터링을 통하여 하천 전반 및 통합물관리에 있어 크게 기여할 것이라 사료된다.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2022.05a
• /
• pp.445-445
• /
• 2022

최근 새만금 방조제 건설이 완료됨에 따라 주변 연안지역의 지형에 많은 변화가 감지되었다. 본 연구대상지는 격포해수욕장으로서 새만금 사업 준공 후 연안침식에 따른 모래 유실 등으로 인해 양빈사업 등이 검토되고 있는 상황이다. 본 연구에서는 연안지형 변화 탐지를 위한 UAV (Unmanned Aerial Vehicle) 활용기술을 제시하는 것으로서 총 3회에 걸쳐 UAV 영상을 촬영하였다. 영상촬영은 DJI Inspire 2 UAV를 활용하였으며 VRS(Virtual Reference Service) 측량성과와 연계하여 Pix4D Mapper SW를 통해 정사영상과 수치표면모델(DSM; Digital Surface Model)을 제작하였다. 먼저 2018. 6. 29 ~ 2018. 12. 10 사이의 지형변화 탐지를 수행한 결과 침식과 퇴적의 최대값은 각각 2.56m와 2.24m로 나타났으며 평균적으로는 0.01m의 퇴적이 발생하였다. 그리고 2018. 6. 29 ~ 2019. 6. 14 동안의 침식과 퇴적의 최대값은 각각 2.31m와 2.28m로 나타났으며 평균값은 0.02m의 침식이 발생하였다. 또한 2018. 12. 10 ~ 2019. 6. 14 사이에는 침식과 퇴적의 최대값이 각각 2.28m와 2.55m로 나타났으며 평균값은 0.03m의 침식이 발생하였다. 지형변화를 보다 상세히 모니터링하고자 퇴적과 침식구간을 나누어 분석을 수행한 결과, 2018. 6. 29 ~ 2018. 12. 10 사이에는 0.5m 이내의 침식과 퇴적구간 면적이 각각 13,324.4m²와 14,667.3m²로 퇴적구간의 면적이 1,342.9m² 만큼 높게 나타났으며, 2018. 12. 10 ~ 2019. 6. 14 사이에는 0.5m 이내의 침식과 퇴적구간 면적이 각각 16,176.6m²와 11,723.0m²로 침식구간의 면적이 4,453m² 만큼 높게 나타났다. 또한 2018. 12. 10 ~ 2019. 6. 14 사이에는 0.5m 이내의 침식과 퇴적구간 면적이 각각 16,821.6m²와 11,126.4m²로 침식구간의 면적이 5,695.2m² 만큼 크게 분석되었다. 이와 같이 UAV 영상 기반의 연안지형 모니터링을 수행할 경우 시계열 지형변화를 효과적으로 모니터링할 수 있으며, 이러한 업무는 새만금 방조제 건설에 따른 지형변화의 영향평가 등 다양한 연안업무에 활용될 수 있을 것이다.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2022.11a
• /
• pp.187-187
• /
• 2022

최근 선박의 자율운항기술이 활발하게 연구되어 오면서, 경로추종 제어 및 충돌회피 등의 자율운항 기술 연구가 많이 진행되고 있으며 그에 따른 시뮬레이션과 실해역 시험 등도 활발하게 수행되고 있다. 이러한 자율운항기술 중 본 연구에서는 AUV(Autonomous Underwater Vehicle) 진회수 시 모함에 활용되며 쌍동선형을 갖는 쌍동형 무인수상선을 대상으로 경로추종 제어에 대한 실해역 시험을 수행한 내용을 소개한다. 대상선인 쌍동형 무인수상선은 배수량이 약 10ton, 최대속도 10knots를 기준으로 설계된 선형이며 Sail drive 타입의 쌍축 추진기를 탑재하고 있으며 Fig. 1에 나타내었다. 실해역 시험은 경기도 화성시에 위치한 제부마리나 전면 해역에서 여러 속도에 대해 Fig. 2의 경로(빨간색)를 활용하여 수행되었다. 해당 경로는 변침각이 45도까지 이루어져 있다. 경로추종 제어 알고리즘은 목표경유점을 향하기 위해 선수각을 제어하는 부분과 목표속도로 추진하기 위해 속도를 제어하는 부분으로 나뉘어져 있다. 선수각 제어 시 경로와 무인선과의 위치 오차를 줄이는 방향으로 선수각이 향할 수 있도록 알고리즘이 설계되었다. 속도 제어의 경우 RPM 별로 실제 속도를 계측하여 데이터화 한 후, 실제 속도가 명령 속도와 다를 경우 RPM을 가감하여 명령 속도로 추진하기 위해 제어할 수 있도록 하였다. Fig. 2에서 파란색 선은 설계한 알고리즘을 활용하여 경로추종 제어를 한 결과의 궤적을 보여준다.

• Journal of the Society of Disaster Information
• /
• v.14 no.4
• /
• pp.501-509
• /
• 2018

Purpose: UAV-based photo measurements are being researched using UAVs in the space information field as they are not only cost-effective compared to conventional aerial imaging but also easy to obtain high-resolution data on desired time and location. In this study, the UAV-based high-resolution images were used to perform the land cover classification. Method: RGB cameras were used to obtain high-resolution images, and in addition, multi-distribution cameras were used to photograph the same regions in order to accurately classify the feeding areas. Finally, Land cover classification was carried out for a total of seven classes using created ortho image by RGB and multispectral camera, DSM(Digital Surface Model), NDVI(Normalized Difference Vegetation Index), GLCM(Gray-Level Co-occurrence Matrix) using RF (Random Forest), a representative supervisory classification system. Results: To assess the accuracy of the classification, an accuracy assessment based on the error matrix was conducted, and the accuracy assessment results were verified that the proposed method could effectively classify classes in the region by comparing with the supervisory results using RGB images only. Conclusion: In case of adding orthoimage, multispectral image, NDVI and GLCM proposed in this study, accuracy was higher than that of conventional orthoimage. Future research will attempt to improve classification accuracy through the development of additional input data.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.37 no.6
• /
• pp.525-533
• /
• 2019

There are two feature collection methods in digital mapping using the UAV (Unmanned Aerial Vehicle) Photogrammetry: vectorization and stereo plotting. In vectorization, planar information is extracted from orthomosaics and elevation value obtained from a DSM (Digital Surface Model) or a DEM (Digital Elevation Model). However, the exact determination of the positional accuracy of 3D features such as ground facilities and buildings is very ambiguous, because the accuracy of vectorizing results has been mainly analyzed using only check points placed on the ground. Thus, this study aims to review the possibility of 3D spatial information acquisition and digital map production of vectorization by analyzing the corner point coordinates of different layers as well as check points. To this end, images were taken by a Phantom 4 (DJI) with 3.6 cm of GSD (Ground Sample Distance) at altitude of 90 m. The outcomes indicate that the horizontal RMSE (Root Mean Square Error) of vectorization method is 0.045 cm, which was calculated from residuals at check point compared with those of the field survey results. It is therefore possible to produce a digital topographic (plane) map of 1:1,000 scale using ortho images. On the other hand, the three-dimensional accuracy of vectorization was 0.068~0.162 m in horizontal and 0.090~1.840 m in vertical RMSE. It is thus difficult to obtain 3D spatial information and 1:1,000 digital map production by using vectorization due to a large error in elevation.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.40 no.2
• /
• pp.257-264
• /
• 2020

Vectorization is currently the main method in feature collection (extraction) during digital mapping using UAV-Photogrammetry. However, this method is time consuming and prone to gross elevation errors when extracted from a DSM (Digital Surface Model), because three-dimensional feature coordinates are vectorized separately: plane information from an orthophoto and height from a DSM. Consequently, the demand for stereo plotting method capable of acquiring three- dimensional spatial information simultaneously is increasing. However, this method requires an expensive equipment, a Digital Photogrammetry Workstation (DPW), and the technology itself is still incomplete. In this paper, we evaluated the accuracy of low-cost stereo plotting system, Menci's StereoCAD, by analyzing its three-dimensional spatial information acquisition. Images were taken with a FC 6310 camera mounted on a Phantom4 pro at a 90 m altitude with a Ground Sample Distance (GSD) of 3 cm. The accuracy analysis was performed by comparing differences in coordinates between the results from the ground survey and the stereo plotting at check points, and also at the corner points by layers. The results showed that the Root Mean Square Error (RMSE) at check points was 0.048 m for horizontal and 0.078 m for vertical coordinates, respectively, and for different layers, it ranged from 0.104 m to 0.127 m for horizontal and 0.086 m to 0.092 m for vertical coordinates, respectively. In conclusion, the results showed 1: 1,000 digital topographic map can be generated using a stereo plotting system with UAV images.

• Korean Journal of Remote Sensing
• /
• v.37 no.6_1
• /
• pp.1731-1738
• /
• 2021

The objective of this study was to extract individual trees and tree heights using UAV drone images. The study site was Gongju national university experiment forest, located in Yesan-gun, Chungcheongnam-do. The thinning intensity study sites consisted of 40% thinning, 20% thinning, 10% thinning and control. The image was filmed by using the "Mavic Pro 2" model of DJI company, and the altitude of the photo shoot was set at 80% of the overlay between 180m pictures. In order to prevent image distortion, a ground reference point was installed and the end lap and side lap were set to 80%. Tree heights were extracted using Digital Surface Model (DSM) and Digital Terrain Model (DTM), and individual trees were split and extracted using object-based analysis. As a result of individual tree extraction, thinning 40% stands showed the highest extraction rate of 109.1%, while thinning 20% showed 87.1%, thinning 10% showed 63.5%, and control sites showed 56.0% of accuracy. As a result of tree height extraction, thinning 40% showed 1.43m error compared with field survey data, while thinning 20% showed 1.73 m, thinning 10% showed 1.88 m, and control sites showed the largest error of 2.22 m.